 |
Active Autowerke Blow Off Valve Kit - E82 135i, E9x 335i w/ N54
(more info)
Protect you turbo from excess pressure build up.
The Active Autowerke single BOV - Blow Off Valve Kit - sports a huge venturi, designed to handle excess pressure build-up against the turbo compressor impeller blades, which can damage the compressor wheel and shaft. With our valve in place, the stock turbos are protected as the boost is raised – you can safely increase HP and get that cool “whoosh” sound as your BMW spits out excess inlet pressure.
All hardware & fittings have that quality factory look you demand, and are built to perform flawlessly under the most aggressive boost conditions.
Key Features:
High-efficiency single displacement BOV – takes place of two smaller plastic valves
Large opening can handle maximum boost, provide high flow
Proven and tested to handle 600+ HP
All aluminum venturi design with factory-style throttle clamp
CNC machined flange
Durable black powder-coated wrinkle finish
Illustrated instruction manual & installation guide for easy “Plug ‘n Play”
This item fits the following BMWs with N54 engine:
2008-2010 E82 BMW 135i
2006-2010 E90 BMW 335i 335xi 335i xDrive
2007-2010 E92 BMW 335i 335is 335xi 335i xDrive
2010+ E92 BMW 335is
2007-2010 E93 BMW 335i
|
| Part #: AABOVKIT-N54 |
| Price: $595.00 (USD) |
|
|
|
|
 |
CRC Mass Air Flow Sensor Cleaner, 11 Oz Can
(more info)
CRC HFM cleaner is specifically developed to clean mass air flow sensors. Increases horsepower & improves air/fuel ratio and MPG. Plastic safe-dries in seconds! Perfect for cars that have had "over-oiled" performance filters installed. Over-oiling can cause the HFM to gum up, this is the perfect solution. This item cannot ship air freight or internationally. UPS Ground shipping to the lower 48 US states only. |
| Part #: 05110 |
| Price: $11.95 (USD) |
|
|
|
|
 |
Genuine BMW Performance Air Intake Kit - E82 128i, E88 128i - 2008+
(more info)
Upgrading to a E82 128i BMW Performance air intake system will unleash gains of up to 3 horsepower and 3 ft-lbs. of torque for your 1 Series, while also helping the engine to operate more efficiently with a 30% reduction in back pressure and increased overall performance. Kit includes new air box, covers and filter.
This item fits the following BMWs:
2008+ E82 BMW 128i
|
| Part #: 13720444749
(13-72-0-444-749)
|
| Price: $899.95 (USD) |
|
|
|
|
 |
ITG Foam Filter for Eurosport/Conforti Intake Kits
(more info)
Replacement ITG Foam Filter for Conforti Intake Kits. Available in 3" and 3.5" opening (see below for applications) or check your filter box for correct appliaction. Filter
comes pre-oiled but oil recharge kit is recommended for future maintenance.
Click here for approved cleaning methods for ITG foam filters.
Applications:
3.5" (blue box): all Euro HFM kits (E36 M3, MZ3), E46 330, late E46 325, E39 530, E39 540, Z3 3.0
3.0" (green box): all other models not listed above (E36 M3/MZ3 with stock HFM, E36 325/328, E46 323/328, E39 525/528, Z3 2.3/2.8) |
| Part #: JC60/73 / JC60/86 |
| Price: $84.95 (USD) |
|
|
|
|
|
 |
No-Toil Foam Filter Oil (for ITG Filters)
(more info)
Don't use harsh solvents like gasoline to clean your ITG on your Eurosport/Conforti intake kit (or similar foam filter element). This product is all you need to maintain your ITG foam filter, and is recommend for use with all Conforti Cold-Air Intake Kits.
When cleaning an ITG foam filter, ITG recommends using warm water and a mild detergent (simple dish soap is fine). Strong detergents and solvents can harm the foam, and cause the filter to break down. Once dirt, dust and debris are rinsed out of the filter, it should be re-oiled to ensure proper function of the filter. ITG recommends No-Toil filter oil, as it is safe to the foam filter media, and is completely waterproof. Drive with more peace of mind through heavy rain and puddles.
Please note, as this product is an aerosol, it MUST BE SHIPPED BY UPS GROUND. Sorry, this can not be shipped outside of the US/Canda.
|
| Part #: NTO-AEROSOL |
| Price: $10.95 (USD) |
|
|
|
|
 |
Stett Performance Charge Pipe with Dual Diverter Valves - E9x 335i/xi, E82 135i with N54 engine
(more info)
The factory plastic charge pipe and diverter valves are prone to leaking under stock boost levels, increasing boost only makes this problem worse. The stock diverter valves are not designed internally to handle added boost pressure. They can fail under load which will actually cause boost bleed off when you don't want it causing boost spikes and loss of horsepower. The STETT Performance 135i/335i charge pipe is made from 100% 304 stainless steel and designed to handle higher than stock boost levels without leaking thanks to it's very strong design, ultra high quality materials and our patent pending throttle body connector that forms an ultra tight seal and prevents the charge pipe from blowing off as is so common with other products on the market. The factory plastic piece begins to leak on even stock level boost. Simply using a standard silicone hose connector to connect an aftermarket pipe leaves a high chance the pipe will blow off the engine. We, however, developed a patent pending 4 ply, double layer hose connector to the throttle body which is far superior to anything else on the market including the factory flimsy o-ring and lock clip. Each kit comes with everything you need for installation including the dual billet aluminum diverter valves from Forge, one of the most respected names in the industry. Each pipe comes standard with dual stainless meth bungs.
Made in the U.S.A.
304 stainless steel replaces factory plastic
Ultra high quality and strong materials
Eliminate leaks caused by weak factory connections
Get back horsepower lost from weak factory diverter valves
Our patent pending hose connector eliminates pipe from blowing off engine under load
Dual stainless Meth bungs
Extreme Duty silicone hoses
High strength stainless hardware
This item fits the following BMWs:
2008-2010 E82 BMW 135i
2011-2012 E82 BMW 1M Coupe
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-2010 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-2010 E93 BMW 335i - Convertible
2011-2012 E92 BMW 335is - Coupe
2011-2012 E93 BMW 335is - Convertible
|
| Part #: SPEE82E92DDV |
| Price: $595.00 (USD) |
|
|
|
|
Intake Kits and Individual Intake Components
