Free Shipping on orders $99 and up! Some exclusions apply. Contiguous US only.

E9 30CS Fan and Fan Clutch Tools

Servicing your BMW often involves removing the mechanical cooling fan. This can be a pain without proper tools and you risk damage to your pulley without doing the job the right way. Our water pump pliers, wrenches, and fan clutch tools are gathered on this page for the correct service of your BMW.
You're currently viewing parts for your 3.0CS. Reset your chassis
For accurate results, specify your model below.
Tool - 32mm / 36mm Fan Clutch and Oil Filter Cap Open-End Wrench Why buy two tools when you can get one that will do many jobs like this open end wrench? It is great for removing and installing the fan clutch and plastic oil filter cap. Also works great for removing and installing the VAN0S solenoid on M50 engine family. Use the same tools the Turner Motorsport techs use!
Turner Motorsport
Part #: TMI9910334
Price: $44.39 (USD) 
$64.95 (Sale - Save 32%)
$64.95
Limited Qty Sale
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Schwaben Wire Crimper/Stripper Pliers

All the features you could ask for from electrical pliers.

Features:

  • Crimp & Strip 10 to 22 gauge
  • Wire & Bolt cutter
Schwaben
Part #: 010840SCH01A
Price: $12.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Schwaben Coolant Refill/Air Purge Tool

When it comes to BMW's we all know the weak point is commonly in the cooling system, many models proving hard to bleed the air pockets out after the refresh. The coolant refill tool solves this problem, ensuring that you get an air pocket free fill. The entire task is as simple as draining the system like normal, reinstalling the drain plugs and hooking the tool up to your refill location. The reason this tool works so well is due to the venturi valve, it converts air pressure from the compressor to vacuum inside the cooling system, then with a twist of a valve sucks coolant right into the system using the vacuum pressure.  


This tool requires access to a standard air compressor with a minimum rating of 90 PSI (6.2 bar).  A convenient, though not required part to complete the job is a container large enough to hold the entire coolant mixture capacity for your vehicle.  This will dramatically reduce the risk of any unwanted air being drawn into the system.  This tool is designed to refill the cooling system after it has been drained.

 

Schwaben
Part #: 003466SCH01
Price: $76.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Schwaben Open Barrel Crimping/Stripping Pliers

This Schwaben Crimping/Stripping 8 in 1 pliers feature:

  • 10" long handles
  • Rubber grip on handle
  • End wire cutter
  • Non Insulated crimper for 0.5, 2.5 and 4-6 
  • Open barrel non insulated for 1.5, 2.5 and 4-6
  • Insulated terminal 2.5-6MM, 1.5-2.5MM , 0.5-1.5MM
  • Wire stripper for AWG , 20,22,18.16,14,12,10
  • Bolt cutter size M2.6, M4, M5, M3.5, M3
Schwaben
Part #: 019639SCH01A
Price: $24.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Schwaben 32mm / 36mm Fan Clutch and Oil Filter Cap Open-End Wrench

Why buy two tools when you can get one that will do many jobs like this open end wrench? It is great for removing and installing the fan clutch and plastic oil filter cap. Also works great for removing and installing the VAN0S solenoid on M50 engine family. Use the same tools the Turner Motorsport tech's use!

Features:

  • Made of Chrome Vanadium Steel for strength
  • 32/36mm open end sides

 

Schwaben
Part #: DO-3236
Price: $19.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Schwaben Water Pump Pulley Holder for Removal of Fan Clutch Replacing the fan clutch on most BMW models requires holding the water pump pulley while removing the fan clutch lock nut. With less than 1 1/2" clearance on some models this project can easily turn into a mechanical nightmare. Using our special slim line fan clutch wrench in conjunction with the appropriate pulley spanner, the removal and installation required only a few moments.
Schwaben
Part #: 001170SCH01A
Price: $24.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Schwaben Long-Reach 32mm Open End Fan Clutch Wrench This tool was specifically designed for the tight clearances needed to remove most BMW fan clutches. Its slim design lets it fit into tight areas, and the extra-long length is ideal for fan shroud clearance. 
Schwaben
Part #: 007701SCH01A
Price: $23.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Tool - 6mm Flexible Nut Driver for Hose Clamps The best tool for tightening hose clamps and a favorite among our techs. When a clamp is in a tight spot it can be frustrating to get a screwdriver or socket on. This tool has a flexible shaft to bend and reach inconvenient clamps. The other common issue for clamps is that using a screwdriver can actually push the clamp away to an even worse position. The nut driver is definitely the superior hose clamp tool. This tool will quickly become one of your favorites!

This nutdriver is made in Germany and has a 6mm socket - the most common size for German hose clamps and the correct size for the OE-grade clamps we sell.
Stahlwille
Part #: 12506-6
Price: $33.95 (USD) 
Ships in 2 Days
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
  • 22 years of BMW Tuning.
  • Award winning service.
  • 10,000's of parts in stock.
  • Quality BMW Parts only.
  • Hassle-free returns.

  • Find us on Facebook