Free Shipping on orders $99 and up! Some exclusions apply. Contiguous US only.

BMW F02 Caliper Rebuild Kits

BMW F02 Caliper Rebuild Kits Brake caliper piston seals are there to maintain brake system pressure and prevent fluid from leaking out from inside the caliper. When a seal goes bad or becomes damaged the brakes lose pressure, leading to a soft brake pedal, sticking caliper, or even a total loss of your brakes. Brake calipers also need periodic rebuilds because the inner piston can seize from rust. With a piston stuck in the retracted position, the brakes are no longer functioning on that wheel. If the caliper is stuck in the extended position it's putting clamping force on your brakes - dragging the brakes, front wheel vibrations, pulling to one side, excessive brake dust and heat, and potentially even a brake pad fire. For cars that see significant track use, regular caliper rebuilds are essential because higher temps lead to rubber seal failures sooner.

Rebuilding your calipers should be part of a regular brake overhaul. The calipers must be removed from the car and disassembled. It's not a particularly difficult job to do but is messy and takes some expertise so that you don't ruin the piston or new seals. Rebuilding calipers is more cost effective than buying replacement calipers. However you service the calipers don't prolong their maintenance until it's too late!
You're currently viewing parts for your (F02) 7-Series LWB 2009+. Reset your chassis
For accurate results, specify your model below.
ECS Performance Caliper Guide Bushing Set - Most Models

This caliper bushing kit will eliminate flex caused by weak rubber caliper bushings. As the brake pedal is pressed the caliper grabs the rotor and twists on its mounting bushings. The rubber bushings allow the caliper to deflect and twist which affects pedal feel and results in uneven pad wear. These solid brass bushings will not twist or deflect so your calipers can squeeze the pads evenly on both sides of the rotor (sort of like what multi-piston big brakes do). This will give you much longer pad life and a more consistent pedal feel. This is the most complete kit we have ever sold with stainless steel caliper slide bolts, o-rings, and new dust boots. Unlike other kits, these bushings are pressed into the caliper and will not shift or slide on their own.

Installation is straightforward: remove the old rubber bushings and press in the new brass bushings (we recommend special tool 003326ECS03). High temp caliper grease or anti-seize is required. The new bushings include an inner o-ring that helps trap grease on the slide bolt, reducing friction and wear.

***Click here for installation instructions*** 

***Click here for the installation tool***

For most models with floating calipers. Fits the rear of E90/2 and E60, but for the front you'll need the kit found here. Does not fit E30 models with Girling calipers, but is compatible with Ate calipers. 

ECS
Part #: 003326ECS01
Price: $102.95 (USD) 
In Stock
Free Shipping Free Shipping
Quantity:   
Front Brake Caliper Rebuild Kit - E9x M3, E82 E39 E60 & more A kit to rebuild one front caliper includes caliper piston seals. Price is per caliper.

This item fits the following BMWs:
2011 E82 BMW 1M Coupe
2008-2011 E90 BMW M3 - Sedan
2008-2013 E92 BMW M3 - Coupe
2008-2013 E93 BMW M3 - Convertible
1997-2003 E39 BMW 525i 528i
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i
2010+ F07 BMW 535i GT, 535i xDrive GT, 550i GT, 550i xDrive GT
2011+ F10 BMW 528i 528i xDrive 535i 535i xDrive 535d 535d xDrive 550i 550i xDrive
2004-2010 E63 BMW 645ci 650i
2012+ F12 BMW 640i 640i xDrive 650i 650i xDrive
2013+ F06 BMW 640i Gran Coupe 640i xDrive Gran Coupe 650i Gran Coupe 650i xDrive Gran Coupe
2002-2008 E65 BMW 745i 745li 750i 750li 760i 760li
2009+ F01 BMW 740i 740li 740li xDrive 750i 750li 750i xDrive 750li xDrive 760li
2007-2013 E70 BMW X5 3.0si X5 4.8i X5 xDrive30i X5 xDrive35d X5 xDrive35i X5 xDrive48i
2014+ F15 BMW X5 sDrive35i X5 xDrive35d X5 xDrive35i
2008-2014 E71 BMW X6 xDrive35i
2015+ F16 BMW X6 sDrive35i X6 xDrive35i
Genuine BMW
Part #: 34111163647
Price: $26.85 (USD) 
$31.23 (14% off MSRP)
Ships in 6 days
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
StopTech Caliper Piston Rebuild Kits

Stoptech Big Brake calipers are designed to be serviced and rebuilt just like any factory caliper. The pistons will probably last the life of the car but the seals can become brittle from extreme heat or extreme cold. Sometimes they just get damaged from debris. For racing environments it's best to rebuild the calipers often (maybe even several times a year). At least you should always have spare caliper seals on hand.

These are the genuine Stoptech caliper seals (dust boots and pressure seals). We sell these to service a PAIR of pistons (1 boot and 1 seal per piston). You will need to measure your existing pistons or seals to order the correct rebuild kits. Sorry, there are too many variables to tell you which pistons you have with only your car info. It's easy to measure and you don't have to remove the pistons from the calipers. Stoptech pistons are metric sized and in 2mm increments. Use the chart below to match your measurments to a rebuild kit.
 

There are a few ways to determine which caliper seals you need. You can measure from the overall outside diameter of the dust boot (A); the inside diameter of the piston (B); or the outside diameter of the piston body (not the tip protruding from the seal!) (C). If measuring the piston body the whole piston has to come out of the caliper housing. Just measuring the tip will give a false measurement. Remember to measure each of your pistons as piston sizes can vary even within the same caliper. Click the image at left for a larger version.

 

Use the table below to determine which Stoptech rebuild kit you need:

Outer Boot
Diameter, "A"Piston Inner
Diameter, "B"Piston Outer
Diameter, "C"Stoptech Kit #

3611.7026143.99026K

3813.4528143.99028K

4015.2030143.99030K

4216.9532143.99032K

4418.7034143.99034K

4620.4536143.99036K

4822.2038143.99038K

5023.9540143.99040K

5225.7042143.99042K

5427.4544143.99044K

5629.3046143.99046K


We sell rebuild kits for a PAIR of pistons - 1 seal and 1 boot per piston. For example -
For a 4-piston caliper you only need to order 2 rebuild kits.
For a 6-piston caliper you only need to order 3 rebuild kits.
But make sure you measure each piston!

These rebuild kits fit with StopTech caliper pistons only. Sorry, returns are not accepted for opened piston seal kits.

StopTech
Part #: TMS213589DK
Price: $25.00 (USD) 
Direct Ship
Stainless Caliper Guide Bolt (42mm Length)

The caliper sliding bolts are one of the most overlooked wear items in your braking system. Subjected to constant motion and often without adequate lubrication the guide bolts see a lot of wear and tear. Factory BMW caliper guide bolts are very expensive from the dealer - these 304 stainless steel bolts are less than half the price and provide outstanding resistance to corrosion and wear. They are manufacturered with tighter tolerances than the factory bolts too.

Price is per bolt unless noted (2 required per caliper).

Enter your vehicle info for specific fitment information.

ECS
Part #: 34111157041KT5
Price: $9.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
ECS Performance Brake Caliper Guide Bushing Installation Tool Set

Installs bushings straight and true with minimal effort. Includes tools for both iron and aluminum calipers. Purchase only one tool set for your entire caliper guide bushing upgrade - tools are not one time use.

 

***Click here for installation instructions*** 

 

ECS
Part #: 003326ECS03
Price: $21.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Caliper Bushing Upgrade Kit (CBMW1)

This kit will eliminate caliper twisting caused by rubber guide pin bushings. This kit, consisting of precision guide pins and machined brass guide bushings will allow your calipers to squeeze evenly on both sides of the brake rotor, just like expensive multi-piston big brake kits. This will result in much longer pad life and more consistent brake system feel. These are a must if you race your BMW. This kit is SCCA and BMW CCA Club Racing approved. This kit fits both the front or rear calipers (but sold per axle). The ideal set-up is to run both front and rear on your car. Installation is quite simple. Does not fit E30 318/325 with Girling calipers nor E24 M6/E28 M5.

*For the rear calipers only of E9X 335i and E9X M3 models*

ATE
Part #: 34111157038
Price: $59.95 (USD) 
In Stock
Quantity:   
  • 22 years of BMW Tuning.
  • Award winning service.
  • 10,000's of parts in stock.
  • Quality BMW Parts only.
  • Hassle-free returns.

  • Find us on Facebook