Free Shipping on orders $99 and up! Some exclusions apply. Contiguous US only.

BMW F26 Performance Intake Kits

BMW F26 Performance Intake Kits The BMW Performance line of intake kits deliver power gains with exceptional engineering and good looks. BMW Performance Intakes are designed to take advantage of a larger air filter to gain more cool air for the engine. The cooler and denser air will develop more power and torque. BMW engineers this kit for a perfect fit with materials and design consistent with the rest of the engine bay. With a factory-designed performance intake you get the power gains of an aftermarket kit blended with style and engineering direct from BMW.
You're currently viewing parts for your (F26) X4 2015+. Reset your chassis
For accurate results, specify your model below.
SnowPerformance Stage 2 MAF-Based Water/Meth Injection Kit - N55

The Stage 2 kit from Snow Performance, allows you to extract the maximum amount of power from your N55. If you're looking to run more boost or , this kit is the perfect solution. This kit operates based on 0-5 volt signal from your vehicles Mass Air Flow Sensor - this signal allows the controller to adjust flow progressively, giving you accurate injection across the whole power band. 

Features:

  • 300 PSI UHO (Ultra High Output) Pump
  • 3 Quart Reservoir
  • MAFU Progressive Controller for Use With All MAF/MAP Sensors
  • Pig Tail Harness
  • All Tubing Necessary for Installation
    • 10' ¼ Inch High Temp Nylon Tubing
    • 3' (Black) Wire Loom
  • Level Switch Upgrade
    • 1 Nozzle Holder/Check Valve Combo
    • 2 Hyper-Sonic™ Nozzles
    • Required Hardware for Install
    • Snow Performance Running S Decal
    • Comprehensive Instructions to Install on Any Vehicle Utilizing a MAF/MAP Sensor
    • Snow Performance 1-Year Warranty 
    • MADE IN THE USA!
    SnowPerformance
    Part #: 20012
    Price: $482.95 (USD) 
    In Stock
    Free Shipping Free Shipping
    Quantity:   
    SnowPerformance Stage 2 Boost-Controlled Water/Meth Injection Kit - N20 N54 N55 N63 S55 S63

    The Snow Performance Stage 2 Boost Cooler™ is the most advanced gauge style water-meth system on the market. This kit includes a boost referenced VC-50 controller, the Stage 2 has the ability to progressively command 2 Hyper-Sonic™ Nozzles on an independent basis. This sophisticated injection system yields the highest increases in HP and cooling all along the power band. The VC-50 controller features a dual 7 color OLED screen and displays boost, percentage of injection, low level, and 2 fault modes (clogged line/unplugged line) directly on the screen. 

    Features:

    • 300 PSI UHO (Ultra High Output) Pump
    • 3 Quart Reservoir
    • All Tubing Necessary for Installation
      • 10' ¼ Inch High Temp Nylon Tubing
      • 18" High pressure Boost Line
      • 3' (Black) Wire Loom
    • 2 1/16 VC-50 Controller
    • Pigtail Harness
    • 2 1/16 Gauge Pod
    • Level Switch Upgrade
    • 1 Nozzle Holder/Check Valve Combo
    • 2 Hyper-Sonic™ Nozzles
    • Required Hardware Needed For Installation
    • Snow Performance Running S Decal
    • Comprehensive Instructions to Install on Any Forced Induction Vehicle
    • Snow Performance 1-Year Warranty 
    • MADE IN THE USA!
    SnowPerformance
    Part #: SN0210
    Price: $549.99 (USD) 
    In Stock
    Free Shipping Free Shipping
    Quantity:   
    SnowPerformance Stage 1 water/Meth Injection Kit - N52 N54 N55

    The Snow Performance Stage 1 kit enables you to get the maximum performance out of your BMW. Whether tuning for more boost or seeking improved cooling, this kit is the ideal solution. This stage 1 controller, operates based on boost load. When your selected boost target is hit, the water/meth mix is injected through the nozzle. This system is ideal for low to medium boost set ups (1-15 PSI). Flow can also be set based on full throttle, among other user-controlled options. If you are looking for a system that operates off the MAF signal, see the Snow Performance Stage 2 kit. 

    Features:

    • 300 PSI UHO (Ultra High Output) Pump
    • 3 Quart Reservoir
    • All Tubing Necessary for Installation
      • 10' ¼ Inch High Temp Nylon Tubing
      • 18" High pressure Boost Line
      • 3' (Black) Wire Loom
    • Boost Switch (1-15 PSI)
    • Pig Tail Harness
    • Level Switch Upgrade
    • 1 Nozzle Holder/Check Valve Combo
    • 2 Hyper-Sonic™ Nozzles
    • Required Hardware Needed For Installation
    • Snow Performance Running S Decal
    • Comprehensive Instructions to Install on Any Forced Induction Vehicle
    • Snow Performance 1-Year Warranty
    • MADE IN THE USA!
    SnowPerformance
    Part #: 20001
    Price: $356.95 (USD) 
    In Stock
    Free Shipping Free Shipping
    Quantity:   
    SnowPerformance Stage 3 Boost Controller - N54 N55

    This stage 3 boost controller will easily upgrade your existing stage 2 kit to stage 3. This digital boost controller gives you the ability to easily dial in your setup - simply set your start and full points, and the software handles the rest. Two buttons allow you to make adjustments. The LCD display shows boost pressure, fuel injector duty cycle, and flow percentage. 

    Features:

    • LCD Screen
    • Digital Variable mapping
    • Comprehensive Instructions
    SnowPerformance
    Part #: 60061
    Price: $418.95 (USD) 
    Ships on Jun 6, 2018
    Free Shipping Free Shipping
    Quantity:   
    SnowPerformance 2.5 Gal (9.3L) Reservoir This 2.5 gallon reservoir increases your capacity over the 3 quart tank that is included in most kits.
    SnowPerformance
    Part #: 40014
    Price: $99.95 (USD) 
    Ships on Jun 6, 2018
    Free Shipping Free Shipping
    Quantity:   
    BMC
    Part #: FB651/20
    Price: $70.29 (USD) 
    $82.00 (14% off MSRP)
    Direct Ship
    Quantity: