Free Shipping on orders $99 and up! Some exclusions apply. Contiguous US only.

BMW F80 Anti-Freeze and Coolant

BMW F80 Anti-Freeze and Coolant
You're currently viewing parts for your (F80) M3 2015+. Reset your chassis
For accurate results, specify your model below.
Evans Waterless Coolant PREP Fluid - 1 Gallon

When switching to Evans Waterless Coolant - it is necessary to make sure your system contains <3% water post-conversion.

Evans Prep Fluid is a Hygroscopic waterless cooling system flush designed to remove any remaining water left after draining all conventional anti-freeze and water from your BMW's engine. Evans Prep Fluid should be used to complete a successful conversion to Evans coolant, but it is not a substitute to a thorough drain of all cooling system components via a block drain. Evans recommends running Prep Fluid through your cooling system before refilling with Evans High Performance Waterless Coolant to ensure your water content is below 3% (54.4 Brix). This can be tested with an Analog Refractometer: T#553530

Features:

Properties: Hygroscopically absorbs water.
When to use: After draining 50/50 coolant from the cooling system.
Benefits: Ensures all residual water is removed from the system.

NOTE: Prep Fluid is not to be used as coolant. This product flushes water out of your system to successfully convert to Evans Waterless Coolant.

Evans
Part #: EC42001
Price: $33.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Rowe BMW Coolant/Antifreeze - 1 Gallon

Rowe is an OEM supplier to BMW among other German manufacturers and their coolant is a monoethylene glycol basis that meets BMW N60069.0 standards. It is free of nitrite, amine and phosphate, just like the OE BMW coolant, making it safe to use in all of BMW's aluminum radiator cores. Mix Rowe BMW coolant 1:1 with distilled water to provide anti-freeze protection to -35*F. Using the proper BMW coolant will ensure sufficient cooling in summer and protection against freeze-ups in winter. For proper maintenance we recommend that your BMW's cooling system be drained and refilled every two years.

Note that most BMW cooling systems take 8+ liters of a 50/50 mix of coolant and distilled water (1 gallon = 3.79 liters), so plan accordingly.

ROWE
Part #: 82141467704
Price: $19.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
BMW Coolant / Antifreeze, 1 Gallon Jug The use of Original BMW Anti-Freeze/Coolant will ensure sufficient cooling in summer and protection against freeze-ups in winter. BMW Antifreeze/Coolant will also guard your vehicle's various engine components against corrosion.

BMW Anti-Freeze/ Coolant will prevent excessive silicate gel precipitation, which may cause plugging of the cooling system and lead to more extensive repairs. For proper maintenance we recommend that your BMW's cooling system be drained and refilled every two years with Original BMW Anti-Freeze/Coolant. It was developed to be compatible with BMW's aluminum radiators, and is nitrite- and phosphate-free to prevent excessive silicate build-up.

Note that most BMW cooling systems take 8+ liters of a 50/50 mix of BMW coolant and distilled water. BMW sells this coolant in 1 gallon jugs (1 gallon = 3.79 liters), so plan accordingly.
Genuine BMW
Part #: 82141467704
Price: $20.89 (USD) 
$24.50 (Sale - Save 15%)
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Schwaben Oil Storage Catch Can - 10-Liter

Large capacity oil drain catch can lets you perform a mess-free oil change and dispose of your drain oil responsibly.

Features:

  • Made from rugged ABS
  • 10 liter capacity (large enough to hold two oil changes from most passenger cars and light trucks)
  • Large double handles and drain spout with screw cap
  • Fill and vent plugs have o-ring seals to prevent leakage

 

Schwaben
Part #: poc-10
Price: $19.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Evans High Performance Waterless Coolant - 1 Gallon

Evans High Performance Waterless Coolant is a proprietary base fluid with an inhibitor package designed for all gasoline, light duty diesel, LP, and CNG engines. Evans does not contain water, giving it the ability to protect your engine below -40°F and above 375°F. Its higher boiling point eliminates the risk of overheating, as well as Boil-Over and After-Boil. Without boiling there is effectively no pressure in the cooling system, thus reducing stress on the system.This is particularly important when your vehicle is under constant load for extended periods of time, such as on the track or during spirited driving.  Evans allows your vehicle to continue cooling when your engine is at high temperatures - Evans does not develop air pockets that prevent traditional coolants from flowing at high temperatures.

While Evans is ideal for both daily driven vehicles and track vehicles, it is also great for vehicles that spend most of their time in storage. Evans Waterless Coolant does not have any of the corrosive properties of traditional coolant - it will not separate and cause corrosion while your vehicle sits in storage. Evans is practical in most BMW applications.

Features:

Benefits: Reduces System Pressure, Prevents Overheating, Maximizes BHP
Boiling Point: Above 375°F
Antifreeze Properties: Protects below -40°F
Corrosive Properties: Unbeatable protection against corrosion and electrolysis
Life Span: Protects for life of the engine
Toxicity: Low Toxicity
Eliminates Overheating: Evans Waterless Coolants have a boiling point above 375°F and will not vaporize, thus eliminating overheating, boil-over and after-boil.
Reduces Pressure: Evans Waterless Coolants generate very low vapor pressures reducing stress on engine cooling system components.
Increases BHP: Evans Waterless Coolants eliminate pre-ignition and detonation caused by overheating - thus improving combustion efficiency and delivering more power.

NOTE: To ensure optimum performance, Evans recommends flushing your cooling system with PREP Fluid: T#553532 before filling with Waterless Coolant

Evans
Part #: ec53001
Price: $46.52 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
BMW Antifreeze Coolant - 1 Liter Bottle This 1 liter bottle is perfect for topping of the coolant in your BMW. This is The use of Original BMW Anti-Freeze/Coolant will ensure sufficient cooling in summer and protection against freeze-ups in winter. BMW Antifreeze/Coolant will also guard your vehicle's various engine components against corrosion. BMW Anti-Freeze/ Coolant will prevent excessive silicate gel precipitation, which may cause plugging of the cooling system and lead to more extensive repairs. For proper maintenance we recommend that your BMW's cooling system be drained and refilled every two years with Original BMW Anti-Freeze/Coolant. It was developed to be compatible with BMW's aluminum radiators, and is nitrite- and phosphate-free to prevent excessive silicate build-up. Note that most BMW cooling systems take 8+ liters of a 50/50 mix of BMW coolant and distilled water. BMW sells this coolant in 1 liter bottles, so plan accordingly. We also sell the 1 gallon jugs of BMW Anti-Freeze
Genuine BMW
Part #: 82142209769
Price: $9.00 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity:   
Red Line Water Wetter Coolant Additive

All sets of 12 now 10% off regular price

Water Wetter is a unique wetting agent for cooling systems which reduces coolant temperatures by as much as 30*F. This liquid product can be used to provide rust and corrosion protection in plain water for racing engines, which provides much better heat transfer properties than glycol-based antifreeze. Or it can be added to new or used antifreeze to improve the heat transfer of ethylene and propylene glycol systems. Designed for modern aluminum, cast iron, copper, brass, and bronze systems.

We have been using RedLine Oil in our street cars and race cars for years. Hands-down, it is the Number One brand of high performance lubricant for BMWs.

Redline
Part #: REDLINE5A
Price: $9.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
BMW Coolant / Antifreeze

The use of coolant/anti-freeze that meets BMW specs will ensure sufficient cooling in summer and protection against freeze-ups in winter. BMW antifreeze/coolant will also guard your vehicle's various engine components against corrosion, while providing critical lubrication for water pump bearings. BMW anti-freeze / coolant will prevent excessive silicate gel precipitation, which may cause plugging of the cooling system and lead to more extensive repairs. For proper maintenance we recommend that your BMW's cooling system be drained and refilled every two years with a coolant that matches BMW spec. It was developed to be compatible with BMW's aluminum radiators, and is nitrite- and phosphate-free to prevent excessive silicate build-up.

The following coolant products meet BMW specs for all BMW models, regardless of year or engine:

  • Genuine BMW (1 liter or 1 gallon containers)
  • Vaico (Made in Germany). Handy 1.5L container
  • Rowe (Made in Germany), OEM supplier to BMW

Note that most BMW cooling systems take 8+ liters of a 50/50 mix of BMW coolant and distilled water. BMW sells this coolant in unmixed containers - 1 liter for top off or 1 gallon (1 gallon = 3.79 liters). Distilled water can be purchased at most grocery stores.

Coolant additives are also available to enhance factory cooling properties. Red Line Water Wetter and Motul MoCool are designed specifically to raise boiling points and reduce combustion chamber temperatures. These can be key to reducing engine knock/detonation on track cars that see exceptionally high underhood temperatures.

Genuine BMW
Part #: BMW-COOLANT
Price: $9.00 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
MOTUL MoCOOL Radiator Additive - 500ml / 16.9 fl oz bottle MoCOOL® is a radiator additive which will reduce cooling system temperature by as much as 15ºC (30ºF). Packaged in 500ml (16.9 fluid ounces) plastic bottles. Concentrated formula that is mixed with distilled water for immediate use. Mix with water at 5% (20:1) Do not use straight out of the bottle.

TYPE OF USE: This performance additive offers better heat transfer than normal coolants. The unique formula also contains rust and corrosion inhibitors. Best used for overheating engines or racing conditions. Inhibits corrosion and water pump protection. Seal, rubber and plastic part friendly!

Designed to be used with pure water at a dilution of 5% (20:1) (for competition use where monoethyleneglycol is not allowed) or mix with your coolant at 5% of volume. Designed for aluminum, cast iron, copper, brass and bronze systems. MoCOOL® is compatible with antifreezes, including the new long-life versions and Original BMW antifreeze.
Motul
Part #: MOCOOL
Price: $14.95 (USD) 
In Stock
Free Shipping Free Shipping
on orders $99 and up
Quantity: