Free Shipping on orders $99 and up! Some exclusions apply. Contiguous US only.

E36 M3 Shark Injector Stage 5 Performance Software (HFM/Cam Kit With No Cats)

Mfg Part #
N3TKAT
Turner Part #
T#340362
Brand
Price:
Qty
449.00
Ships in 2 Days
Free Shipping Free Shipping
Does this fit my vehicle?
For accurate results, specify your model below.

Product Details

Stage 5 Performance Software for 1996-1999 E36 M3 (HFM/injectors/cams/headers/no cats)

Conforti Shark Injector performance software tuned for the highest level of our OBD2 kits - Schrick camshafts, "24lb" injectors, Porsche 809 3.5" HFM, intake, headers, and race exhaust (no cats). This software is tuned around the stock S52 manifold but will work with an M50 manifold as well. This software turns down the sensitivity of the post-cat oxygen sensors so that fault codes and check engine lights for no cats will not appear. This is the full-bore Kit - tuned for every bolt-on upgrade we sell.

With this software you will notice more top end power, a broader torque band, and a smoother running engine. The rev limit is raised to 7000 RPM with the top speed limiter removed. Works with 91 or higher octane fuel.

Required:
"24lb" injectors (actually around 26lb injectors when used at the S52's 3.5 bar of fuel pressure). You must confirm the injector flow-rate at 3.5 bar before using this software. If the injectors were not purchased from us, we may as for the Bosch part number on your injectors.
Porsche 809 3.5" HFM (0 280 217 809) (TMS/Porsche HFM works best) with intake. Note: this will not work with a Euro HFM, 540 HFM, or Dinan HFM. Our software is programmed and written specifically for the Porsche 809 HFM! If you did not purchase the HFM Kit from us, we may ask you for the Bosch part number from your HFM.
Schrick camshafts
Headers (TMS Shorty Headers or similar)
Cat-delete (such as with the AA Track Pipe)

Optional Speed Sensor Delete: Since this software is intended for race or track use only, there is one additional feature we can build into the programming. The Speed Sensor is built into the diff cover - an area prone to excessive heat. During endurance races or very hot track days, the sensor can malfunction or actually melt. If the engine DME does not see this signal, it will restrict RPM to 5500, obviously killing your speed! This optional Speed Sensor delete programming will tell the DME not to care if the sensor is sending a signal or not. It will set the maximum RPM to 7000 RPM electronically.

This part alters or deletes the emissions equipment on your car. Because of this, we require a waiver of emissions compliance to be signed and sent in to TMS. You can download the waiver here.


Shark Injector Installation Instructions
(click to expand)
Shark Injector installation instructions
A capable battery charger is required for the installation. The charger provides backup power supply to the regular car battery during installation. It must be capable of holding a continuous 10amp charge for the full installation (15-20 minutes).
The minimum octane fuel for this software is 91.
Shark Injector FAQ
(click to expand)

This item fits the following BMWs:
1996-1999 E36 BMW M3

 

Loading Kit Configurator

449.00
Current Price
x

Kit Configurator

Current Price:
449.00

E36 M3 Race Software:

Add the recommended battery charger?

Add emissions waiver:

This Part Fits the Following BMWs

Make Model Submodel Engine
BMW E36 M3 S52 3.2L
BMW Z3 M Coupe S52 3.2L
BMW Z3 M Roadster S52 3.2L
*The above product applications have been written by Turner Motorsport. All warranties, product application, fitment, and performance are the responsibility of Turner Motorsport. For additional information see the terms of use.
  • 22 years of BMW Tuning.
  • Award winning service.
  • 10,000's of parts in stock.
  • Quality BMW Parts only.
  • Hassle-free returns.

  • Find us on Facebook