BMW 5 Series E28 (1982-1988)

Bav Auto Trailing Arm Inner Bushing Tool - Master Set

Be sure to add some grease to the rods in this tool set during installation to prevent breakage.

T#:580442

Part#: B8800137

In Stock

Sale - Save 3% $ 293.99

This product was last offered at the strikethrough price on
05-03-2026

$ 285.17 USD

Add to Wish List

Qty

Sale - Save 3%

$ 293.99

This product was last offered at the strikethrough price on
05-03-2026

$ 285.17 USD

Add to Wish List

Remove and install the two rear inner trailing arm / lower control arm bushings that are in the subframe with one tool set without removing the trailing arms from the vehicle. This tool is designed to work with all trailing arm bushing designs on E82, E84, E90 ,E91, E92, E93 model cars. Replaces bushing part #'s 33326770829 and 33326763092.

Show More Show Less

Bav Auto Hub Adapter / Hub Puller

T#:580427

Part#: B8800120

In Stock

Sale - Save 10% $ 109.99

This product was last offered at the strikethrough price on
05-03-2026

$ 98.99 USD

Add to Wish List

Qty

Sale - Save 10%

$ 109.99

This product was last offered at the strikethrough price on
05-03-2026

$ 98.99 USD

Add to Wish List

For use with B8800122 impact driver to remove stuck CV axle shafts.

Radiator / Cooling System Pressure Tester- Bavarian Autosport ...

T#:580397

Part#: B8800084

In Stock

Sale - Save 15% $ 146.99

This product was last offered at the strikethrough price on
05-03-2026

$ 124.94 USD

Add to Wish List

Qty

Sale - Save 15%

$ 146.99

This product was last offered at the strikethrough price on
05-03-2026

$ 124.94 USD

Add to Wish List

Bav Auto Shock and Strut Nut Tool

T#:580394

Part#: B8800081

In Stock

Sale - Save 5% $ 123.99

This product was last offered at the strikethrough price on
05-03-2026

$ 117.79 USD

Add to Wish List

Qty

Sale - Save 5%

$ 123.99

This product was last offered at the strikethrough price on
05-03-2026

$ 117.79 USD

Add to Wish List

Used to install or remove shock and strut nuts - no more using an impact gun!

Bav Auto Oil Extractor - 10 Liter - Inserts Into Dip Stick Tube ...

T#:580333

Part#: B8800001

In Stock

Sale - Save 15% $ 171.99

This product was last offered at the strikethrough price on
05-03-2026

$ 146.19 USD

Add to Wish List

Qty

Sale - Save 15%

$ 171.99

This product was last offered at the strikethrough price on
05-03-2026

$ 146.19 USD

Add to Wish List

Change your oil without getting underneath the vehicle! This oil extractor pulls the oil out of your engine through the dip stick tube.

E24 633/635CSi/M6, E28 535i/M5 JB Racing Lightweight Aluminum Flywhee...

T#:3770

Part#: 520-080-240

Ships in 6 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 22.0lbs
JB Flywheel Weight = 8.5lbs

This flywheel includes the ignition trigger wheel.

This item fits the following BMWs:
1982-1987 E23 BMW 733i 735i
1982-1989 E24 BMW 633csi 635csi M6
1985-1988 E28 BMW 535i 535is M5

Show More Show Less

Bav Auto Smoke Machine Intake Adapter Bladder

T#:580342

Part#: B8800012

Ships in 1 Business Day

Sale - Save 15% $ 89.99

This product was last offered at the strikethrough price on
05-03-2026

$ 76.49 USD

Add to Wish List

Qty

Sale - Save 15%

$ 89.99

This product was last offered at the strikethrough price on
05-03-2026

$ 76.49 USD

Add to Wish List

The inflatable intake adapter quickly and easily adapts to all sizes of intake boots, bellows or pipes, as well as exhaust pipes and other vacuum or pressure system tubes. The adapter assures quick and secure connection of your diagnostic smoker (Evaporative Smoke Machine). No more tapered cones slipping out of the boots or pipes. Simply insert the inflatable bladder into the intake boot (or exhaust) and pump the inflation bulb. The bladder will expand to fit round, oval or other odd shaped boots, pipes, bellows, etc. Once inflated, connect your smoker's outlet hose to the second hose on the adapter. The smoke is injected through the tube in the bladder and into the system being tested.

Show More Show Less