Home
Suspension

BMW Suspension Parts for BMW 7 Series E38 (1995-2001)

Clear BMW chassis

Your BMW's handling is determined by the capabilities and age of your suspension components. Our selected aftermarket performance suspension like coilovers, lowering springs, cup kits, and dampers can improve the handling of your BMW dramatically. With those upgrades comes the needs for proper adjustment; our recommended supporting modifications comes stiffer sway bars, bushings, and adjustable camber/caster plates, to name a few found on this page. Completely build your suspension for the most competitive BMW driving experience, achieve your perfect look, or simply replace your worn suspension with our recommended parts.

Sub-Categories

Sort By:

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E39 540/M...

T#:389661

Part#: 193616-1J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)

Show More Show Less

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E39 540/M5...

T#:389662

Part#: 193616-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)
2004-2010 E60 BMW M5
2004-2011 E63 BMW M6

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E39...

T#:389317

Part#: 193616-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearing: PTFE-lined pillow-ball with thin polyurethane bushing

The Stage 2 KMAC plates are a mixed street/track camber/caster plate meant to be used in a variety of suspensions. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions. Bearing inserts and adapters included. The Stage 2 camber plates are shorter than a factory mount so may not be suitable for cars will little suspension travel. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Front Upper Control Arm - Left - E38 740i/740iL/750iL - OEM Replaceme...

T#:338051

Part#: 31121141721

In Stock at Vendor

Starting at $ 181.08 USD

Add to Wish List

Starting at $ 181.08 USD

Add to Wish List

This upper front control arm (also known as a thrust arm or tension strut) is a direct replacement for the original part and is the OEM Lemforder brand.

Control arms, and their integrated ball joints, are some of the most crucial components on a BMW suspension. The control arms literally control the wheel and suspension as they go through their range of motions. A faulty or worn control arm or ball joint is a very dangerous and potentially life-threatening problem so make sure they are inspected and replaced at regular intervals. For a street-driven car we advise yearly inspection and a full replacement every 3-4 years. For track-driven cars these should be inspected before every event and replaced every two years.

The E38 upper control arms include both the inner and outer bushing.

This item fits the following BMWs:
1995-2001 E38 BMW 740i 740il 750il

Show More Show Less

Front Control Arm Refresh Kit - E38

T#:30497142

Part#: 31121141721KT2

Ships in 1 Business Day

Sale - Save 3% $ 388.99

This product was last offered at the strikethrough price on
05-03-2026

$ 376.87 USD

Add to Wish List

Qty

Sale - Save 3%

$ 388.99

This product was last offered at the strikethrough price on
05-03-2026

$ 376.87 USD

Add to Wish List

Upgrade your BMW’s front suspension with our high-quality Front Suspension Control Arm Kit, designed to restore stability and precision to your vehicle. Over time, worn control arms can lead to creaking, groaning, and instability, especially at highway speeds. Our comprehensive kit ensures a complete overhaul with all necessary components pre-assembled for easy installation.

Key Features:

Enhanced Stability: Say goodbye to wandering and instability on the road with new, durable control arms. Complete Solution: Our kit includes all four front control arms, two ball joints, and essential installation hardware. Premium Quality: Assembled by enthusiasts at Turner Motorsport, ensuring top-notch performance and reliability. Ready for Installation: All related ball joints and bushings are pre-installed, saving you time and effort. Kit Includes:

4 Front Control Arms Give your BMW the suspension upgrade it deserves. Enhance your driving experience with our Front Suspension Control Arm Kit and enjoy the confidence of driving a well-maintained vehicle. Order now and experience the difference in ride quality and stability.

Show More Show Less

Shocks and spring Installation Kit - E38 740i/iL EDC

T#:553626

Part#: 31331090611KT2

Ships in 6 Business Days

$ 462.99

This product was last offered at the strikethrough price on
05-01-2026

$ 457.99 USD

Add to Wish List

Qty

$ 457.99 USD

Add to Wish List

This kit is contains all new strut and shock mounts and hardware needed when installing a aftermarket suspension on your vehicle.

For vehicles with EDC only

Fits the following BMW's

1995-2001 E38 740i 740iL with EDC

Show More Show Less

Shocks and spring Installation Kit - E38 740i/iL Non EDC

T#:553600

Part#: 33521094091KT4

Back Ordered

$ 194.99

This product was last offered at the strikethrough price on
05-07-2026

$ 187.99 USD

Add to Wish List

Qty

$ 187.99 USD

Add to Wish List

This kit is contains all new strut and shock mounts and hardware needed when installing a aftermarket suspension on your vehicle.

Click Here for Spring options

For vehicles without EDC only

Fits the following BMW's

1995-2001 E38 740i 740iL with out EDC

Show More Show Less

11" Ball Joint Separator

T#:641394

Part#: 2287D

Ships in 6 Business Days

$ 41.81 USD

Add to Wish List

Qty

$ 41.81 USD

Add to Wish List

Select Vehicle

Purpose

Category

Home

Suspension

Brand

View All Brands

Price

Special Offers

On Sale (1)

Shipping