Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
The Turner Motorsport Oil Temperature Sensor Flange was designed to get your oil temperature from the best possible location: the sump. Most of the factory and aftermarket sensors are located after the oil pump, which does not give you an accurate temp reading of the oil that is actually lubricating the engine. At the factory temp sensor location the sensor picks up heat not only from the oil stream, but also from the oil pump and housing which will skew the reading. Other aftermarket adapters can be give inaccurate readings from their location and/or design limitations. And may require making unnecessary modifications. By relocating the sensor to the oil sump it reduces clutter and sits flush against the bottom of the oil pan to avoid potential clearance issues. Testing that we have done on and off the track shows that the sump location is the most accurate. We accomplish this by removing the factory oil level sensor or block off plate and using the existing hole and bolt pattern on the oil pan with no additional modifications. Any sensor with an M12 x 1.50mm thread can be used in the flange.
Note that removing the factory oil level sensor will trigger the low oil fault/warning light. There's no elegant way around this but since the Temp Flange is considered a race-only part we assume you will be checking your own oil level anyway or be using a stand-alone dash/engine management system that does not track oil level. And having the most accurate oil temp is more important.
Applications:
1987-1991 E30 M3
1992-1999 3 Series E36 M3 3.0 and M3 3.2 Euro Models Only!
1999-2006 3 Series E46 All
1991-1995 5 Series E34 525i M50
1997-2003 5 Series E39 525i, 528i, 530i, 540i, 540iP, M5
2004-xxxx 5 Series E60 525i, 530i
1995-2001 7 Series E38
Z3 2.5, 2.5i, 2.8, 3.0i, M3.2 S54
Z4 2.5, 3.0
Z8 All
When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.
Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain system comes complete with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.
Features:
At almost half of the normal cost of Genuine BMW Installation Tool - No. 130190, this Schwaben BMW Fuel Injector O-Ring Tool Set is a perfect alternative to save money and ensure your have the proper tool for the job when it come time to service your fuel system. Make sure the job is done correctly the first time with this specialty item, relieving frustration and saving time all while preventing you from damaging critical seals or the injector itself that could otherwise be damaged if using the wrong tools for the job.
This tool set includes all of the same components you would get with the BMW tool, the seal cutting pliers and seal installation components, made to exact specifications for perfect operation.
Once again, ECS Tuning has found a way to make life easier for working on your car. Need new hose clamps but don't want to wait to order it from the dealership or pay more than you should for a hose clamp? That's where we come in! These are full 304 stainless steel hose clamps with various band widths for your convenience. They are German style using T-bolts to adjust in size to your required diameter. Never pay dealer pricing again, but still get the quality you love here at ECS Tuning.
This extra large T60 Torx® driver is not included in many standard Torx driver sets.
Features:
Upgrade your fastening needs with the Allen Head Bolt, a versatile and reliable solution for various applications. Crafted from high-quality materials, these bolts offer exceptional strength and durability. Their allen head design ensures secure tightening and easy access, making them ideal for automotive, construction, and DIY projects. Elevate your projects with the precision and reliability of Allen Head Bolts.
