Transmission and Differential Tools for BMW 7 Series E65 (2002-2008)

Schwaben offers the right tools to make your next project a success. Everything from complex engine scanners to brake bleeders and spring compressors, Schwaben tools has you covered.

Some of the recommended use include but are not limited to:

• Remove and install rear ball joints on E38, E39, E60/61, E63/64, E65/66, and E70's
• Removal and installation of ball joints and bushings on rear control arms on E36, E46, E39, E60/61, E63/64,  E65/66, E70, E83 and E85/86 Z4's
• Removal and installation of rear sub frame mounted differential bushings on E36, E46, E83 and E85/86 Z4's
• Removal and installation of rear differential mounted bushings on E36, E46, E9X, E60/61, E63/64, E65/66, and E85/86 Z4's

This hand held Schwaben tool makes changing fluids an easy, quick task.The Schwaben fluid suction/fill pump suitable for oils, water and any non corrosive liquid.

Features 

• Comes with a flexible and a rigid tube. 
• Flow rate is adjustable for different functions.
• 350 ML capacity
• Cylinder is marked in 20 mL increments and fraction of quarts for accurate filling. 

Not for use with gasoline.

It only takes a gust of wind to have your hood crashing down on your head, or if you have a carbon fiber hood and no longer have the gas struts than this could be what you need.

 This hood prop is adjustable, lightweight, and sturdy making it easy to keep out of the way in the trunk so it's there whenever you need it. 

Commonly used when replacing axle shaft boots.

Features:

• Crimp and flatten design
• Produces a clean factory style crimp
• Limited Lifetime Warranty

Having a low profile floor jack can be a great asset for your garage, perfect for those with a lowered car as well as those that aren't. Most car owners with a lowered vehicle have been in the position of their floor jack not making the clearance needed, the low profile jack is the answer. 

• Dual pump pistons raises the saddle to maximum height in only 5 pump strokes, with minimum effort.
• Special low profile thick frame side plates and reinforced lift arm for added strength and use.
• Wide track front wheels help provide chassis torsion control and durability.
• Angular positioned pump pistons provide maximum effective pump stroke even when jack is completely under the vehicle.
• Ball bearing mounted rear swivel caster wheels for easy maneuverability.
• Side mounted handles for carrying and easy positioning.
• Overload and bypass safety valve prevents jack overload and over extension.
• Two piece quick release padded handle for storage or transport.

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Lenght 50"
• Shipping Weight 50 lbs

The ultra light Schwaben jack stands only weigh 4.7 lbs each. Fit and finish on these stands just shows how much pride in workmanship goes into our stands.These stands are all aluminum construction with heavy-duty  flanged bases to safely stabilize loads. Features 6 locking positions for a secure load in multiple heights. The load pin is extra heavy duty at .584 in. diameter and features a posi lock ball to insure pin stays in place.  

Min. Height is 10.6".

Max Height is 15.4".

Large 7" diameter base.

Outer support tube is 2-1/8" in diameter.

Perfect for any job when it comes to keeping your hands clean and protected.

Features:

• High dexterity
• Elastic hook and loop strap
• Textured latex finger tips for grip
• Breathable material

 A complete set offered to ensure that the proper lifting techniques are at use. It's never wise to work under a vehicle supported by only a floor jack, with this complete kit you get a complete matching set to get the job done safe and fast.

• Special low profile thick frame side plates and reinforced lift arm for added strength and use.
• Wide track front wheels help provide chassis torsion control and durability.
• Angular positioned pump pistons provide maximum effective pump stroke even when jack is completely under the vehicle.
• Ball bearing mounted rear swivel caster wheels for easy maneuverability.
• Side mounted handles for carrying and easy positioning.
• Overload and bypass safety valve prevents jack overload and over extension.
• Two piece quick release padded handle for storage or transport.
• Dual piston's for 5 pump full extension

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Lenght 50"
• Shipping Weight 50 lbs

Schwaben 12" wheel Stands:

These stands are made from special EPS foam with an anti-skid coating.

Won't scratch or mark your floors!

Lightweight at only 5 lbs each, makes these stands easy to carry and maneuver.

Works on virtually any surface, including sand!

Will not scoot, slip or slide, no matter the surface.

Specs:

12" tall,15.75" long,12" wide.

Works on wheel diameters from 25 to 30 inches.