Improve your BMW's driving experience by addressing the wear and tear caused by years on the road. The suspension takes a beating from pot holes, speed bumps, and road hazards, leading to a weakened and sloppy feel. Enhance safety and ride comfort by replacing worn components, such as the control arm.

• Improved driving experience and ride comfort
• Enhanced safety through the replacement of worn suspension components
• Non-serviceable ball joints and other components addressed for prolonged lifespan
• Control arm replacement for a better feel and handling
• Recommended replacement in pairs for optimal performance
• Suitable for both front and rear suspension upgrades
• Referred to as a wishbone by BMW
• Performance upgrade for non-M3 models, recommended to replace in pairs due to heavy-duty nature

Enhance your driving experience with our premium suspension upgrade for your BMW. Over time, the road can take a toll on your suspension, leading to a sloppy and weak feel while driving. Our solution? Replace the control arm – a critical component that, after years of service, may wear out. Boost safety and ride comfort with this easy upgrade.

• Improved driving experience
• Enhanced safety
• Better ride comfort
• Extended service life of replacement parts

If you're considering replacing any part of your front or rear suspension, opt for doing it in pairs (both left and right sides). This ensures optimal performance and longevity of the replacement parts. In the BMW world, it's often referred to as a wishbone.

For non-M3 models, this isn't just a replacement – it's a performance upgrade. These heavy-duty components are recommended to be replaced in pairs to maximize their efficiency and provide a seamless driving experience.

The rear lower control arms on E82/E9X models are the weakest link in the rear suspension. The arm is made from folded sheetmetal and it bends and deforms easily. Not only will it deform from potholes and curbs, tow truck drivers love to hook onto them without realizing how weak they are. We have seen other race teams complete the box section to make them stronger. A bent arm will throw off the geometry in the suspension, potentially affecting handling and tire wear. These aluminum arms are both lighter and stronger than the factory sheetmetal arms and is the best solution for chronic bending of the stock arm. These are a direct replacement to your stock arms with no changes needed to your alignment. New high-grade hardware is included.

Note: the stock arm is designed from the factory to be intentionally weak. These arms will bend so that something else in the suspension does not break. Our race cars used the stock sheetmetal arm but we replaced them often. We found that it was better to finish a race with a bent arm than not finish due to a catastrophic failure. The ECS arms are still designed to be the weakest link but are far stronger than the factory arm and will not bend as easily.

This item fits the following BMWs:

2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi M3 - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible

Fine-tuning your coilover damping shouldn’t mean stripping out your rear seats or interior panels. On many applications, rear shock adjusters are hidden behind carpet, trim, or seatbacks, making quick adjustments a hassle.

The ECS Rear Damping Extension Kit solves that problem with a clean and functional solution. These flexible extensions relocate the adjustment knobs to an easily accessible point above the rear shock towers, letting you dial in your suspension from inside the cabin, no disassembly required.

Installation is straightforward: simply drill a small access hole in your interior trim and route the extension cables through. The adjustment knobs can be removed to allow the line to pass through smaller openings, minimizing cutting. For proper installation, be sure to fully loosen the set screw, insert the cable, then securely tighten it using the provided Allen key.

Kit Includes:

(2) Rear damping adjuster extension cables

Installation hardware and Allen key

A smart upgrade for track cars, daily drivers, or anyone who values easy access to suspension tuning, without compromising interior fit and finish.

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints: Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability

Revamp Your Suspension with the BMW & MINI Coilover Wrench Set

• Compatible with BMW and MINI models for versatile use
• Durable construction ensures long-lasting performance
• Ergonomic design provides comfortable handling during installation
• Allows for precise adjustment of coilovers for optimal ride quality

Upgrade your BMW or MINI's suspension system with the BMW & MINI Coilover Wrench Set. This set is compatible with various BMW and MINI models, offering versatile compatibility for a wide range of vehicles. Constructed from durable materials, these wrenches are built to withstand the rigors of frequent use and provide long-lasting performance. The ergonomic design ensures comfortable handling during installation, reducing fatigue and allowing for more efficient work. With the BMW & MINI Coilover Wrench Set, you can easily adjust your coilovers to achieve the optimal ride quality for your vehicle. Access Secret Premium Dashboard