BMW Intake Parts for BMW 3 Series E90 (2006-2011)

The intake boot is a regular issue especially for BMW's, nearly all vehicles have a boot manufactured from rubber with an accordion section in the design for flexibility. This flexible section is typically where the failure comes from, leading to vacuum leak engine codes, rough idle, and increase fuel consumption. 

When you upgrade to a Turner silicone intake boot you get a perfect fit that will not only outlast the OE design (meaning any vacuum leaks and rough idle), while also smoothing out airflow within the intake tract. This boot also eliminates the factory intake resonator giving your engine a much more aggressive sound under the hood especially at higher rpm. Available in black or Turner blue color, our intake boot offers either a pop of color or a cohesive, complementary look in your engine bay.

The Turner Motorsport silicone intake boot is manufactured with 5 layers of wire reinforced silicone to prevent collapse under load. Engineered in-house utilizing 3D scanning technology, this boot offers perfect fitment with the factory air box and either single stage or three stage (high output N52) intake manifolds.

Install as a standalone reliability improvement or in addition to our three stage intake manifold and Turner performance tune (available here).

Replaces OE intake boot 13717536004.

Features:

• 5 layers of wire reinforced silicone
• Perfect fitment with factory airbox
• Compatible with single stage or three stage manifold
• Installation hardware included

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i Coupe Convertible
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi - Coupe
2007-2013 E93 BMW 328i - Convertible

Full carbon fiber intake to increase flow, performance and aesthetics! Dual inlet design for maximized air flow while retaining the OEM+ fitment.

The most common N55 intake utilizes a short plastic tube and oversized cone filter; it is your job to have better taste than the common N55 owner. This carbon intake changes the whole image of the N55 engine while maintaining a flow of cool air and added induction noise. With a dual inlet design the engine bay retains its functionality while adding a second inlet to provide your engine with improved air flow and sound. To ensure the engine gets the coolest air possible the second inlet is located in the "sweet spot" on the cold side of the engine for the lowest intake air temps and most air flow possible. The cone filter features a bellmouth velocity stack filter that creates the satisfying flutter after letting of the throttle.

Our Turner Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Engineers use the 3D imaging of the chassis to design the intake in SolidWorks modeling software. Using a Flow Bench, the Intake is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations and proven to flow better than factory.

Key Benefits:

Increased flow over the factory intake
Carbon fiber airbox and intake tube with gloss clear coat for UV protection
CAD-Designed for perfect Integration
Custom high flow air filter specially designed to to pair with the carbon fiber airbox
Kit Contents:

Carbon Intake Tube
Full Carbon 2 Piece Airbox
Bellmouth Velocity Stack Cone Filter
Billet Turbo Inlet Adapter
Silicone Coupler
Hardware For Installation
Design:

- Carbon Fiber Intake Tube

Carbon inlet tube featuring a smoother interior without corrugations for a smooth flow path.
Integrated carbon flange allows secure mounting of the tube to the carbon air boxes.
Intake tube is manufactured using 2x2 twill weave carbon fiber for a great look in the engine bay.
Gloss finish clear coat for UV protection.
4-ply reinforced silicone coupler and 6061-T6 black anodized aluminum flange that utilizes the factory o-ring and retaining clip.
- Air Box

Carbon fiber airboxes are manufactured using 2X2 twill weave carbon fiber and protected with a gloss finish clear coat for UV resistance to match the intake tube.
Air box mounts in stock location with supplied hardware.
- Air Filter

Conical hi-flow reusable air filter; featuring 8 ply oiled cotton gauze construction to maximize filtration efficiency.
Bellmouth (velocity stack) filter flange inlet to reduce turbulence in order to maximize flow.
Product Development:

Turner N55 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.

Fitment:

E82 135i N55
E88 135i N55
E84 X1 35i
E90 335/xi N55
E92 335/xi N55
E93 335/xi N55

At Turner, all our Carbon Fiber Intake Systems are top-of-the-line custom-engineered products that we develop in house. Our Turner S65 Carbon Intake is a monster that perfectly compliments the high revving 4.0l V8 engine. Add in a full carbon plenum and you have a recipe for greatness! The intake benefits start right at the motor; the plenum offers a larger interior volume and full carbon design which helps boast the intoxicating roar. Directly connected to the plenum is a full carbon intake tube with a substantially larger cross sectional area with smooth transitions which results in more airflow available to the engine in high demand scenarios. The inlet tube mounts securely to the full carbon heat shield and is mounted in factory airbox locations while retaining the factory cold air induction tract from the hood. Housed inside the heat shield is a behemoth cone filter to ensure proper filtration and maximize airflow. Turner's S65 intake and plenum is designed with air flow and induction in mind. The intake flows like no other; during testing, the Turner intake outperformed the flow-bench at over 750CFM, a massive improvement over the factory intake.

Here are the benefits:

Full carbon plenum and intake for a full engine bay transformation
You get a beautiful carbon heatshield, one of the only full carbon fiber heatshields available.
All the flow - the air on demand will make sure your engine always has room to breathe.
Increased throttle response.
Added induction noise for an intoxicating driving experience.
PART DESIGN:

Designed and engineered in-house using state of the art 3D laser scanning and CAD technology for precision fitment
Full Carbon Plenum construction with internal bracing and velocity stacks
Hood Inlet Scoop - Directs the flow of cool, ambient air to the heat shield, and directly into the air filter. Seals off with the factory rubber gasket on the lower side of the hood inlet.
Full Carbon Fiber Heat Shield Assembly that utilizes OEM air box mounts and integrates with the factory air intake tract from the hood.
Monstrous 9" cone air filter to maximizes filtration that is able to be serviced/cleaned.
7"x5" Carbon Fiber Inlet Tube providing smooth, direct airflow from the behemoth air filter directly into the plenum.
Fully compatible with the OEM Secondary Air Injection emissions system. Factory hose lock and location.
Full carbon fiber plenum with bracing and carbon velocity stacks.
KIT CONTENTS

Carbon Fiber Plenum
Carbon Fiber Heat Shield
Carbon Fiber Intake Tube
Plenum Silicone Coupler
9" Cone Air Filter
Installation Hardware
PRODUCT DEVELOPMENT

Turner S65 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.

Maximize performance and reduce intake air temperatures on your E90 335d with the Turner Motorsport Stepped Intercooler. Designed as a direct-fit upgrade for the factory intercooler, this high-efficiency unit increases charge air volume and airflow, helping your diesel-powered BMW run cooler, stronger, and more efficiently.

Cooler air is denser air, and denser air means more power. By reducing intake air temperatures (IATs), this upgraded intercooler allows your M57 engine to pack in more air and fuel per cycle, translating to improved performance across the RPM range.

Engineered for performance and durability, the Turner stepped intercooler features cast aluminum end tanks and a bar-and-plate core design, offering superior thermal efficiency and structural strength. Compared to the stock unit, it delivers a 65% increase in both frontal surface area and internal cross-sectional flow, ensuring better heat dissipation and reduced pressure drop. All of this performance comes in a lightweight package under 20 lbs.

Finished in a stealthy black coating with laser-etched Turner logos, this intercooler not only performs but looks good doing it.

Key Features:

Designed specifically for the E90 335d (M57 engine)
Cast aluminum construction for durability
High-efficiency bar-and-plate core
65% increase in frontal and cross-sectional area
Significantly lowers IATs for improved power and reliability
Reduced pressure drop for more consistent boost delivery
Lightweight design – under 20 lbs
Dimensions: 520mm wide × 200mm tall × 150mm deep
Direct bolt-on installation – no modifications required
If you're looking to get the most out of your E90 335d, the Turner Motorsport Stepped Intercooler is a must-have upgrade for your turbo diesel intake system.

Enhance your BMW driving experience with the Turner Motorsport E9X 335i (N55) Valved Catback Exhaust. Designed for hearty exhaust notes and improved performance, this exhaust system offers a subtle factory-like sound with closed valves and a menacing growl when opened. Crafted with Mandrel bent dual 2.5” 304SS pipes and a high-flow valved stainless steel muffler, it ensures efficient gas flow.

The kit includes Turner Mid Pipes, a Valved Exhaust, Muffler Valve Controller Kit, and engraved Exhaust Tips. Accuseal slip-fit joints simplify installation, making it a bolt-on replacement for the OE version. The full exhaust system is available as Axle Back, Cat-back, or a full Turbo back system, providing a dual-purpose solution for both your neighbors and your desire for volume.

Key Features:

• Mandrel bent dual 2.5” 304SS pipes with brushed finish
• Turner Engraved Polished exhaust tips
• High flow, valved, stainless steel mufflers
• Accuseal slip-fit joints for easy fitment
• Utilizes factory exhaust hangers

N55 Carbon Intake:

Upgrade your N55 engine with the Turner Carbon Intake, breaking away from common setups. The dual inlet design adds functionality without compromising engine bay aesthetics. Located in the "sweet spot," the second inlet maximizes airflow and lowers intake air temps. The bellmouth velocity stack design reduces turbulence for a satisfying flutter after throttle release. The carbon fiber airbox and intake tube feature a gloss clear coat for UV protection, offering a beautiful OEM+ upgrade.

Turner Carbon Fiber Intakes are CAD-designed, ensuring optimal airflow improvement over stock. The kit includes a Carbon Intake Tube, Full Carbon 2 Piece Airbox, Bellmouth Velocity Stack Cone Filter, Billet Turbo Inlet Adapter, Silicone Coupler, and Hardware for Installation.

Key Benefits:

• Increased flow over the factory intake
• Carbon fiber airbox and intake tube with gloss clear coat
• CAD-Designed for perfect integration
• Custom high-flow air filter
• Smooth interior carbon inlet tube for optimal airflow

Design Features:

Carbon Fiber Intake Tube:

• Smooth interior without corrugations for a streamlined flow path
• Integrated carbon flange for secure mounting
• 2x2 twill weave carbon fiber construction
• Gloss finish clear coat for UV protection
• 4-ply reinforced silicone coupler and 6061-T6 black anodized aluminum flange

Air Box:

• 2X2 twill weave carbon fiber construction
• Gloss finish clear coat for UV resistance
• Mounts in stock location with supplied hardware

Air Filter:

• Conical hi-flow reusable air filter
• 8 ply oiled cotton gauze construction
• Bellmouth (velocity stack) filter flange inlet for reduced turbulence and maximized flow

Unleash the roar of your N52 engine with the Turner Motorsport E9x N52 Muffler & Resonator Delete Kit. Elevate your driving experience by transforming your exhaust with this cost-effective kit, providing performance gains, a captivating exhaust note, and stunning exhaust tips. Shedding the heavy factory muffler, Turner's T304 stainless steel 3.0" tubing replaces it, delivering a lighter, high-flow solution compatible with the OEM rear valance. Easy to install with hand tools, this muffler delete adds a powerful sound without significant drone, while shaving off about 20lbs from your vehicle. Upgrade your N52 without replacing the entire exhaust system!

Key Features:

• Turner designed Muffler & Resonator Delete for N52 engine
• T304 stainless steel construction with 1.25mm wall thickness
• CNC mandrel-bent 3.0" tubing for optimal exhaust gas routing
• Tig-welded exhaust hangers for direct fitment
• Hand-Tig welded joints for durability
• Stainless steel Accuseal exhaust clamps for a leak-proof seal
• Large radius bends ensure smooth transitions for optimal flow

Kit Includes:

• Y-pipe section
• Tailpipe section
• Dual 3.0" exhaust tips (Black Chrome finish)
• Stainless steel Accuseal exhaust clamps

See and hear the difference on the ECS YouTube page.