BMW Internal Engine Parts for BMW 7 Series F02 (2009+)

Supertech Single Groove Exhaust Valve - Priced Each

T#:21472889

Part#: BMEVI-1055S-HS

Ships in 8 Business Days

$ 55.99 USD

Add to Wish List

Qty

$ 55.99 USD

Add to Wish List

Single Groove sodium filled exhaust valves for high performance builds Head Diam: 28mm (std) Material: Inconel-Nimonic / Sodium Filled Groove Type: Single Groove Length: 112.9mm Stem Diam: 5.96mm

Show More Show Less

5mm Single Groove Valve Keeper - Set Of 24

T#:21604314

Part#: KPR-5.0-7S-24

In Stock

$ 72.99 USD

Add to Wish List

Qty

$ 72.99 USD

Add to Wish List

Two required per valve, for use with certain supertech valves 5.0mm single groove

ARP Performance Head Stud Kit - N54

T#:1061441

Part#: ARP-HSK-N54

Ships in 2 Business Days

$ 554.99 USD

Add to Wish List

Qty

$ 554.99 USD

Add to Wish List

Despite the fact that BMW engineers some of the worlds most revered engines, during number crunching something always has to be a compromise. One item that is always found to be a weak point- the OEM hardware. It is definitely sub-par for real performance use under high stress such as modded engines and track use. We use these fasteners on all of VAC's in-house head builds. Whenever the head is coming off, your switching to forced induction, or if you are simply prepping to drive your car hard; we highly recommend switching to far superior race-grade hardware. These Head Stud Kits greatly improve reliability; helping to eliminate movement of the of the cylinder head and intern, gasket failure caused by inferior OEM head-bolt stretch. This is the #1 cause of premature head gasket failure, especially on boosted or high output engines. Though more expensive than OEM, converting to one of VAC's head studs kits will not only give added strength and reliability when its needed most, but provides the most accurate torque readings because studs don’t “twist” into the block; all clamping forces are on one axis, and there is less force exerted on the normally stressed threads of the block. This increases block and hardware life and typically makes the head easier to properly install to the block, a blessing if your head may have to be removed more than once. Especially in the time crunch of racing, when engines are dissembled frequently, studs make removing and installing the cylinder head on to the block a much easier task. By allowing the studs to act as a guide on to the head, your head slides on and off and also ensures proper alignment of the head and gasket for the same reason. It is similar to converting your wheel-bolts to wheel-studs.

Show More Show Less

BMW N54 ARP Head Stud Kit

T#:17538610

Part#: ARP-HSK-N54-14

In Stock

$ 599.99 USD

Add to Wish List

Qty

$ 599.99 USD

Add to Wish List

The VAC Motorsports ARP Head Stud Kit was put together by VAC and ARP’s finest engineers. This is a completely custom kit designed specifically for the almighty N54. *High Boost (25+ psi application) option features: (14) 11mm ARP Head Studs (14) ARP Washers for 11mm Studs (14) ARP Nuts for 11mm Studs Install Tips: MUST drill and tap the (4) 9mm holes in the engine block to make them 11mm holes. This way all the engine block holes are 11mm, and fit ALL (14) 11mm Studs. Torque Specs: All studs torque down through 3-equal steps to 95 ft lbs ***This is NOT the Chrysler and Volvo stud kits! VAC Motorsports and ARP engineers designed and assembled this kit with high grade material, specifically so standard street-use or high-boost N54 owners have a PROPER kit that does not fail over time, such as the retro-fit Chrysler and Volvo head stud kits. ARP is the world leader in fastener technology. Makers of the finest fasteners in the market, especially for BMW engines, ARP is the brand you can count on when you want the highest reliability possible. If you are looking for high performance from your BMW engine, then ARP Head Stud Kits are a must. All kits come complete with hardened parallel-ground washers and aerospace-quality nuts.

Show More Show Less

Ferrea High Performance Valve Spring Kit for BMW N55/S55

T#:23416526

Part#: FER-HPVSK-N55

Ships in 3 Business Days

$ 1,049.99 USD

Add to Wish List

Qty

$ 1,049.99 USD

Add to Wish List

Maximize your N55 or S55 engine's performance with Ferrea Valve Springs and Retainers, precision components crafted from chromoly alloy. These springs undergo special thermal treatment, ensuring exceptional durability even in extreme racing conditions. Addressing issues like valve binding, breakage, and float, Ferrea valve springs are meticulously heat-treated and stress-relieved, providing stability for high-lift and high-RPM racing engines while minimizing load loss. Precision CNC machined titanium retainers offer superior strength and stability. Ferrea's Spring Seat Locators, made from 4140 chromoly alloy, guarantee precise tolerances and a flat, parallel spring pad with a hard Nitride surface treatment for exceptional toughness and anti-wear characteristics. Please note that installation requires the expertise of an engine builder.

Show More Show Less

WPC-Treated Performance Rod Bearing Service Kit - N63 / S63

10X Entries Into Our F80 M3 Sweepstakes

T#:36066266

Part#: 11247617338KT2

In Stock

$ 1,098.99

This product was last offered at the strikethrough price on
09-29-2026

$ 1,093.99 USD

Add to Wish List

Qty

$ 1,093.99 USD

Add to Wish List

If your engine has higher mileage, don't neglect rod bearing replacement! These bearings are sandwiched between the connecting rod and crankshaft journal and are prone to failure due to overheating, lack of lubrication, or general wear. Replace your rod bearings and prevent a spun bearing.

Starting with ACL’s high-performance bearing shells, our Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Kit includes

Turner Motorsport WPC-Treated Race Series Rod Bearing Shells (16) Genuine BMW Connecting Rod Bolts (16) Hardware for Oil Pan & Oil Sump Oil filter Liqui-Moly Molygen 5W-40 (6L) Drain Plug Turner Motorsport Oil Reminder Sticker Oil pan gasket RedLine assembly lube (4 oz.)

Show More Show Less

Supertech Forged Pistons - Set Of 6

T#:21604329

Part#: P6-BMN55-84-T-6

In Stock

$ 984.99

This product was last offered at the strikethrough price on
05-21-2026

$ 904.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 984.99

This product was last offered at the strikethrough price on
05-21-2026

$ 904.99 USD

Limited Qty Sale

Add to Wish List

Supertech forged pistons are a great choice for performance engine builds! Bore: 84.00mm Over Size: STD Comp Ratio: 10.2:1 Dome dish: -10.4 Head CCs: 37cc Comp Height: 32.40mm Stroke: 89.60mm Skirt style: Slipper Design Rod Length: 141.35mm Pin Diam: 22mm Material: 4032 Application: All Motor / Turbo Ring part number: R84-GNH8400 (MUST BE PURCHASED SEPARATELY)

Show More Show Less

CP Forged Piston Set - N63 - Pro-Xtreme 9.5:1

T#:26238409

Part#: CP-FPS-N63-XT-HD

Ships in 3 Business Days

$ 2,464.99 USD

Add to Wish List

Qty

$ 2,464.99 USD

Add to Wish List

The 5150 AutoSport Pro-Xtreme Forged Pistons, made by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW N63 engines. Constructed from high-strength, aircraft-grade steel, these pistons are engineered to withstand the forces generated by high-powered engines. The Pro-Xtreme Piston design is specifically engineered to handle up to 2000 horsepower, making these pistons suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each piston is precisely fabricated to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Pistons are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines. Includes: - Pistons - HD Wrist Pins - PVD Rings - Pins - Locks - Spec Sheet

Show More Show Less

CP-Carrillo Connecting Rod Set - N63/S63 Pro-Xtreme

For Use With Aftermarket Pistons Only!

T#:26238404

Part#: CAR-CRS-S63-XT

Ships in 3 Business Days

$ 2,899.99 USD

Add to Wish List

Qty

$ 2,899.99 USD

Add to Wish List

5150 AutoSport Pro-Xtreme Connecting Rods, manufactured by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW N63 and S63 Engines. The Pro-Xtreme design is specifically tailored to handle up to 2000 horsepower, making them suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each connecting rod is precisely engineered to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Connecting Rods are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines.

Show More Show Less

Performance N55 Main Bearing Set

T#:26238415

Part#: 5150-HPMBS-N55

Ships in 3 Business Days

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

5150 High Performance Coated Main Bearing Sets are made for the demands of high performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

BMW N55 S55 Ferrea High Performance Valve Kit

T#:23416508

Part#: FER-HPVK-S55-T-3

Ships in 3 Business Days

$ 929.99 USD

Add to Wish List

Qty

$ 929.99 USD

Add to Wish List

Increase the power output of your N55/S55 engine with the high-performance Ferrea valve kit. Renowned as the industry's most reliable extreme-duty valves, they're meticulously crafted from aerospace-grade alloys, employing an exclusive two-step slow forging process for optimal grain flow and material structure integrity. A 48-hour heat treatment and stress-relieving process enhance molecular integrity. The valves feature avionics-quality hard chrome and a specially applied hard tip. Standard size: 32mm intake / 28mm exhaust, with a triple groove valve design. Compatible with factory valve locks ("Valve Keepers"), the kit includes 12x Intake Valves and 12x Exhaust Valves for a comprehensive engine upgrade!

Show More Show Less

Victor Reinz Cylinder Head Bolt Set - BMW N63 S63

For vehicles with a production date up to 10/2011

T#:27672116

Part#: 11127582454

Ships in 1 Business Day

$ 55.99

This product was last offered at the strikethrough price on
05-07-2026

$ 48.99 USD

Add to Wish List

Qty

$ 48.99 USD

Add to Wish List

One time use torque-to-yield cylinder head bolts. Always replace as a set whenever cylinder head is removed and reinstalled.

CP-Carrillo Pro-Xtreme Connecting Rod Set - BMW N63/S63

T#:23681818

Part#: CAR-CRS-S63-XTT

Ships in 3 Business Days

$ 2,999.99 USD

Add to Wish List

Qty

$ 2,999.99 USD

Add to Wish List

Tailored for exceptional performance, the Pro-Xtreme design is crafted to handle up to 2000 horsepower and 9500 RPM. Constructed from high-strength, aircraft-grade steel, these connecting rods feature a tapered small-end, allowing them to be paired with your OEM pistons.

Show More Show Less

Victor Reinz Cylinder Head Bolts - N54

T#:373825

Part#: 11127574303

Ships in 1 Business Day

$ 147.99

This product was last offered at the strikethrough price on
10-12-2026

$ 134.99 USD

Add to Wish List

Qty

$ 134.99 USD

Add to Wish List

Head Bolt set for the N54 engines with aluminum block.

If you drive a European vehicle, chances are high your vehicle came equipped with one or more Victor Reinz gaskets. Choose OE quality VR gaskets and seals and do the job right the first time.

Show More Show Less

Eccentric Shaft Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:22789670

Part#: S55SHAFTRPCKT

In Stock

$ 1,209.99

This product was last offered at the strikethrough price on
08-24-2026

$ 1,208.99 USD

Add to Wish List

Qty

$ 1,208.99 USD

Add to Wish List

Ensure the peak performance of your BMW N55 or S55 engine with Turner Motorsport's Eccentric Shaft Replacement Kit. This all-inclusive kit features essential components, including:

Camshaft
Eccentric Shaft Bearing
Valve Cover Gasket Set
Gasket

Designed for precision and durability, this kit guarantees optimal engine performance and longevity. Rely on Turner Motorsport for top-quality replacement parts that adhere to the highest standards.

Show More Show Less

Eccentric Shaft Replacement Kit - N55/S55

10X Entries Into Our F80 M3 Sweepstakes

T#:21735862

Part#: CAMGSKTN55S55KT

In Stock

$ 1,209.99

This product was last offered at the strikethrough price on
08-24-2026

$ 1,208.99 USD

Add to Wish List

Qty

$ 1,208.99 USD

Add to Wish List

When it comes to optimizing the performance and longevity of your BMW N55 or S55 engine, few upgrades can rival the impact of replacing the camshaft, bearings, and gaskets. These essential components play a pivotal role in your engine's overall health and performance, and upgrading them can deliver a host of benefits, from increased power to enhanced reliability. In this article, we'll explore the advantages of investing in these critical upgrades for your BMW N55 or S55 engine. Improved Performance: Upgrading your BMW N55 or S55 engine with a new camshaft can significantly boost its performance. A high-quality camshaft can optimize valve timing, leading to improved airflow and combustion efficiency. This, in turn, results in increased horsepower and torque, providing you with a more exhilarating driving experience. If you're seeking that extra punch when you hit the gas pedal, a new camshaft is the way to go. Enhanced Durability: The camshaft, bearings, and gaskets are fundamental components of your engine's internal structure. Over time, wear and tear can cause these parts to degrade, potentially leading to catastrophic engine failure. By replacing these components with high-quality, performance-oriented alternatives, you're not only increasing horsepower but also reinforcing the engine's durability. This can help prevent costly breakdowns and extend the life of your BMW engine. Optimal Efficiency: Efficiency is a key factor in engine performance. Worn-out bearings and gaskets can lead to oil leaks and reduced engine efficiency. Replacing them ensures a tighter seal, minimizing oil leaks and maintaining the proper lubrication for all moving parts. This leads to better fuel efficiency and a smoother, more reliable engine operation, all while reducing maintenance costs in the long run. Increased Resale Value: Investing in high-quality components like camshafts, bearings, and gaskets not only enhances your driving experience but also adds value to your BMW. When it's time to sell or trade-in your vehicle, potential buyers or dealerships will recognize the value of these upgrades, making your car more desirable and potentially increasing its resale value. Kit for All N55/S55 Engines

Show More Show Less

N54 Crank Hub Service Kit - Up To 02/2011

For vehicles with production date up to 02/2011

10X Entries Into Our F80 M3 Sweepstakes

T#:2227021

Part#: N54PRCRANKT

In Stock

Sale - Save 3% $ 156.99

This product was last offered at the strikethrough price on
05-03-2026

$ 151.69 USD

Add to Wish List

Qty

Sale - Save 3%

$ 156.99

This product was last offered at the strikethrough price on
05-03-2026

$ 151.69 USD

Add to Wish List

All of the components necessary for service when upgrading to an aftermarket crank hub solution.

Supertech Titanium Valve Retainers - Intake - Set Of 12

T#:21604322

Part#: RET-BMN54-TI-12

Ships in 8 Business Days

$ 197.99 USD

Add to Wish List

Qty

$ 197.99 USD

Add to Wish List

7 Degree - 5mm valve stem - Single or Tripe Groove Valves

Supertech Single Groove Intake Valve - Set Of 12

T#:14783498

Part#: BMIVN-1055S-12

Ships in 5 Business Days

$ 310.99 USD

Add to Wish List

Qty

$ 310.99 USD

Add to Wish List

Head Diam: 32mm (std) Material: Stainless Steel 21-4N Groove Type: Single Groove Length: 104.9mm Stem Diam: 4.97mm

Supertech Titanium Valve Retainers - Exhaust - Set Of 12

T#:21604321

Part#: RET-BMN54-TE-12

Ships in 8 Business Days

$ 197.99 USD

Add to Wish List

Qty

$ 197.99 USD

Add to Wish List

7 Degree - 6mm valve stem - Single or Tripe Groove Valves

Performance Dual Valve Spring Kit with Steel Retainers - Set Of 24 ...

T#:21604308

Part#: SPRKFE20N54BE

Ships in 4 Business Days

$ 965.99 USD

Add to Wish List

Qty

$ 965.99 USD

Add to Wish List

Supertech has the high performance valvetrain components you need to take your build to the next level. Can be used with factory valve stem seals and keepers. InnSpr.OD: 21mm InnSpr.ID: 14.2mm Seat Pressure: 75 @ 36.5 Open Pressure: 155 @ 10 Max Lift: 12mm Coil Bind: 23.2mm Rate: 8 Kit spring: SPR-FE20BE Kit spring qty: 24 Retainer: RET-BMN54-TI (5mm) / RET-BMN54-TE (6mm) OutSpr.OD: 24.4mm OutSpr.ID: 17.6mm Retainer qty: 24

Show More Show Less

Supertech Single Groove Exhaust Valve - Set Of 12

T#:14816646

Part#: BMEVI-1055S-HS-1

In Stock

$ 660.99 USD

Add to Wish List

Qty

$ 660.99 USD

Add to Wish List

Single Groove sodium filled exhaust valve set for high performance builds Head Diam: 28mm (std) Material: Inconel-Nimonic / Sodium Filled Groove Type: Single Groove Length: 112.9mm Stem Diam: 5.96mm

Show More Show Less

Conical Spring Kit - Set Of 24

T#:21604309

Part#: SPRKFE20N54BE2

Ships in 5 Business Days

$ 965.99 USD

Add to Wish List

Qty

$ 965.99 USD

Add to Wish List

Supertech has the high performance valvetrain components you need to take your build to the next level. Can be used with factory valve stem seals and keepers. InnSpr.OD: 21mm InnSpr.ID: 14.2mm Seat Pressure: 88 @ 36.5 Open Pressure: 160 @ 10 Max Lift: 12mm Coil Bind: 23.2mm Rate: 7.25 Kit spring: SPR-FE20BE-2 Kit spring qty: 24 Retainer: RET-BMN54-TI (5mm) / RET-BMN54-TE (6mm) OutSpr.OD: 24.4mm OutSpr.ID: 17.6mm Retainer qty: 24

Show More Show Less

Cat Cams N54 Hot Street Camshaft Set

T#:25805752

Part#: 1305002

Special Order: No Guaranteed ETA

$ 1,950.00 USD

Add to Wish List

Qty

$ 1,950.00 USD

Add to Wish List

Upgrade your N54 Engine with Cat Cams, a leader in the performance-aftermarket camshaft industry. These Camshafts will increase airflow into the engine by increasing the overall lift and duration over the factory cams. With their Hot Street cam setup, you can run all factory valvetrain, with no valve spring upgrades necessary! Check the distance between valves and piston to be 1mm at least with VVT engaged. Wrong installation will cause severe engine damage! The VANOS (VVT) system on the intake camshaft changes the PD from 125° to 70°. The data are shown for full intake retard (disengaged VVT).The VANOS (VVT) system on the exhaust camshaft changes the PD from 130° to 85°. The data are shown for full exhaust advance (disengaged VVT). Tuning advised!

Show More Show Less

Cat Cams N54 Race Camshaft Set

T#:25805753

Part#: 1305003

Special Order: No Guaranteed ETA

$ 1,950.00 USD

Add to Wish List

Qty

$ 1,950.00 USD

Add to Wish List

Upgrade your N54 Engine with Cat Cams, a leader in the performance-aftermarket camshaft industry. These Camshafts will increase airflow into the engine by increasing the overall lift and duration over the factory cams. With their race cam setup, you can run all factory valvetrain, with no valve spring upgrades necessary! Check the distance between valves and piston to be 1mm at least with VVT engaged. Wrong installation will cause severe engine damage! The VANOS (VVT) system on the intake camshaft changes the PD from 125° to 70°. The data are shown for full intake retard (disengaged VVT). The VANOS (VVT) system on the exhaust camshaft changes the PD from 130° to 85°. The data are shown for full exhaust advance (disengaged VVT). Tuning Required!

Show More Show Less

Bav Auto Crankshaft Position Sensor - Multiple BMWs

10X Entries Into Our F80 M3 Sweepstakes

T#:639826

Part#: 13627525015

Special Order: No Guaranteed ETA

$ 67.99 USD

Add to Wish List

Qty

$ 67.99 USD

Add to Wish List

This crankshaft position sensor provides the ECU with the engine speed signal. It is mounted in either the engine block or the bell housing of the transmission on most cars. From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

Show More Show Less

BMW N52 N54 Collar Screw

10X Entries Into Our F80 M3 Sweepstakes

T#:17871157

Part#: 11367524954

In Stock

Sale - Save 20% $ 5.99

This product was last offered at the strikethrough price on
05-03-2026

$ 4.79 USD

Add to Wish List

Qty

Sale - Save 20%

$ 5.99

This product was last offered at the strikethrough price on
05-03-2026

$ 4.79 USD

Add to Wish List

Holds the camshaft gear to the camshaft, measures M10X1X94.

WPC Treated Cam Bearing Ledge - Exhaust - BMW N52 2.0L N54 N55 3.0L ...

10X Entries Into Our F80 M3 Sweepstakes

T#:585946

Part#: 11127531224WPC

In Stock

$ 916.99 USD

Add to Wish List

Qty

$ 916.99 USD

Add to Wish List

A common issue on N54 motors is cam bearing ledge scoring due to lack of lubrication, and if left unattended can cause damage to the camshaft and increase oil consumption. These WPC-treated cam bearing ledges help prevent lubrication issues to ensure no scoring occurs on the bearing ledge or camshaft. What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both.

Show More Show Less

Intake Valve - Black Nitride - Oversize

T#:21505753

Part#: BMIVN-1054S-1

Ships in 8 Business Days

$ 25.99 USD

Add to Wish List

Qty

$ 25.99 USD

Add to Wish List

Head Diam: 31.9mm (+0.5mm) Material: Stainless Steel 21-4N Groove Type: Single Groove Length: 106.7mm Stem Diam: 4.96mm

WPC Treated Cam Bearing Ledge Kit - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:14651263

Part#: 11127550913WKT

In Stock

$ 1,815.99 USD

Add to Wish List

Qty

$ 1,815.99 USD

Add to Wish List

A common issue on N54 motors is cam bearing ledges scoring due to lack of lubrication, and if left unattended can cause damage to the camshafts and increase oil consumption. These WPC-treated cam bearing ledges help prevent lubrication issues to ensure no scoring occurs on the bearing ledge or camshaft. What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both.

Show More Show Less

Performance Conical Valve Spring - Sold Each

T#:21472894

Part#: SPR-FE20BE

In Stock

$ 19.99 USD

Add to Wish List

Qty

$ 19.99 USD

Add to Wish List

Supertech has the high performance valvetrain components you need to take your build to the next level. Seat Pressure: 75 @ 37 Open Pressure: 155 @ 10 Max Lift: 12.2mm Coil Bind: 23.20mm Rate: 8 OutSpr.ID: 17.60mm InnSpr.OD: 21.00mm InnSpr.ID: 14.20mm

Show More Show Less

Exhaust Valve - Sodium Filled - Std Size

T#:21505756

Part#: BMEVI-1054S-HS

In Stock

$ 55.99

This product was last offered at the strikethrough price on
05-03-2026

$ 50.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 55.99

This product was last offered at the strikethrough price on
05-03-2026

$ 50.99 USD

Limited Qty Sale

Add to Wish List

Head Diam: 28mm (std) Material: Inconel-Nimonic / Sodium Filled Groove Type: Single Groove Length: 114.9mm Stem Diam: 5.95mm

Forged Connecting Rods - Sold Each

T#:21604327

Part#: CR-BMN55-H144.35

Special Order: No Guaranteed ETA

$ 198.99 USD

Add to Wish List

Qty

$ 198.99 USD

Add to Wish List

Supertech forged rods are a great choice for performance engine builds! These rods come with ARP 2000 hardware and are designed for high powered N55/S55 applications. H-Beam design Forged 4340 alloy Center to center: 144.35mm Be bore: 53.6mm Be width: 20.88 Pe bore: 22mm full float Pe width: 20.88mm tapered ARP 2000 - 3/8" x 1.600" bolts

Show More Show Less

Cat Cams N54 Sport Camshaft Set

T#:25805744

Part#: 1305001

Special Order: No Guaranteed ETA

$ 1,950.00 USD

Add to Wish List

Qty

$ 1,950.00 USD

Add to Wish List

Upgrade your N54 Engine with Cat Cams, a leader in the performance-aftermarket camshaft industry. These Camshafts will increase airflow into the engine by increasing the overall lift and duration over the factory cams. With their Street cam setup, you can run all factory valvetrain, with no valve spring upgrades necessary! The VANOS (VVT) system on the intake camshaft changes the PD from 125° to 70°. The data are shown for full intake retard (disengaged VVT). The VANOS (VVT) system on the exhaust camshaft changes the PD from 130° to 85°. The data are shown for full exhaust advance (disengaged VVT). Check the distance between valves and piston to be 1mm at least with VVT engaged. Wrong installation will cause severe engine damage! The VANOS (VVT) system on the intake camshaft changes the PD from 125° to 70°. The data are shown for full intake retard (disengaged VVT). The VANOS (VVT) system on the exhaust camshaft changes the PD from 130° to 85°. The data are shown for full exhaust advance (disengaged VVT).

Show More Show Less

Exhaust Valve Set - Sodium Filled - Oversize

T#:21505765

Part#: BMEVI1054SHS-1KT

In Stock

$ 660.99 USD

Add to Wish List

Qty

$ 660.99 USD

Add to Wish List

Head Diam: 28.50m (+0.5mm) Material: Inconel-Nimonic / Sodium Filled Groove Type: Single Groove Length: 114.9mm Stem Diam: 5.95mm

Intake Valve - Black Nitride

T#:21505752

Part#: BMIVN-1054S

In Stock

$ 25.99

This product was last offered at the strikethrough price on
06-08-2026

$ 23.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 25.99

This product was last offered at the strikethrough price on
06-08-2026

$ 23.99 USD

Limited Qty Sale

Add to Wish List

Head Diam: 31.40mm (std) Material: Stainless Steel 21-4N Groove Type: Single Groove Length: 106.7mm Stem Diam: 4.96mm

Exhaust Valve - Sodium Filled - Oversize

T#:21505757

Part#: BMEVI-1054S-HS-1

In Stock

$ 55.99

This product was last offered at the strikethrough price on
05-03-2026

$ 50.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 55.99

This product was last offered at the strikethrough price on
05-03-2026

$ 50.99 USD

Limited Qty Sale

Add to Wish List

Head Diam: 28.50m (+0.5mm) Material: Inconel-Nimonic / Sodium Filled Groove Type: Single Groove Length: 114.9mm Stem Diam: 5.95mm

WPC Treated Cam Bearing Ledge - Intake - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:585945

Part#: 11127550913WPC

In Stock

$ 898.99 USD

Add to Wish List

Qty

$ 898.99 USD

Add to Wish List

A common issue on N54 motors is cam bearing ledge scoring due to lack of lubrication, and if left unattended can cause damage to the camshaft and increase oil consumption. These WPC-treated cam bearing ledges help prevent lubrication issues to ensure no scoring occurs on the bearing ledge or camshaft. What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both.

Show More Show Less

WPC Treated Genuine BMW Bearings - Single Bearing

10X Entries Into Our F80 M3 Sweepstakes

T#:5470995

Part#: 11247617339WPC

In Stock

Sale - Save 31% $ 61.99

This product was last offered at the strikethrough price on
05-03-2026

$ 42.63 USD

Add to Wish List

Qty

Sale - Save 31%

$ 61.99

This product was last offered at the strikethrough price on
05-03-2026

$ 42.63 USD

Add to Wish List

Performance Rod Bearing Set - N55

T#:26238416

Part#: 5150-HPRBS-N55

Ships in 3 Business Days

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

5150 High Performance Coated Rod Bearing Sets are made for the demands of high performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

BMW N54 3.0L CP-Carrillo Heavy Duty Wrist Pins

T#:25473980

Part#: CP-PP-HD-N54-6KT

Ships in 3 Business Days

$ 233.99 USD

Add to Wish List

Qty

$ 233.99 USD

Add to Wish List

BMW N54 3.0L CP-Carrillo Heavy Duty Wrist Pins are engineered to enhance the performance and reliability of your BMW's engine. Designed specifically for the N54 3.0L engine, these heavy-duty wrist pins provide superior strength and durability under high-stress conditions. With CP-Carrillo's reputation for high-quality performance parts, these wrist pins ensure your engine operates at its best, delivering exceptional power and longevity.

Superior strength for high-stress conditions
Enhanced engine performance and reliability
Designed specifically for BMW N54 3.0L engines
High-quality construction by CP-Carrillo
Improves engine longevity and durability

Show More Show Less

BMW N55/S55 Valves By Super Tech

T#:39329323

Part#: SUP-HPVK-S55-32/

Ships in 3 Business Days

$ 1,143.99 USD

Add to Wish List

Qty

$ 1,143.99 USD

Add to Wish List

N54 Crank Hub Service Kit - From 02/2011

For vehicles with production date from 02/2011

10X Entries Into Our F80 M3 Sweepstakes

T#:2227020

Part#: N54POCRANKT

In Stock

Sale - Save 3% $ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 146.61 USD

Add to Wish List

Qty

Sale - Save 3%

$ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 146.61 USD

Add to Wish List

All of the components necessary for service when upgrading to an aftermarket crank hub solution.

Timing Chain Kit - N57

10X Entries Into Our F80 M3 Sweepstakes

T#:58271030

Part#: 13528490225KT

Ships in 1 Business Day

$ 1,331.99

This product was last offered at the strikethrough price on
10-11-2026

$ 1,313.99 USD

Add to Wish List

Qty

$ 1,313.99 USD

Add to Wish List

The Turner Motorsport N57 Timing Chain Kit provides complete timing restoration for BMW N57 diesel engines to correct premature factory chain failure. The comprehensive replacement package supplies OEM chains, tensioners, guides, sprockets, and Elring sealing components to ensure precision synchronization. Complete the N57 service utilizing the supplied Hengst filtration, LiquiMoly Top-Tec 5W-40 oil, and BMW G48 coolant.

Show More Show Less

Intake Valve Set - Black Nitride - Std Size

T#:21505754

Part#: BMIVN-1054SKT

Ships in 5 Business Days

$ 310.99 USD

Add to Wish List

Qty

$ 310.99 USD

Add to Wish List

Head Diam: 31.40mm (std) Material: Stainless Steel 21-4N Groove Type: Single Groove Length: 106.7mm Stem Diam: 4.96mm

Supertech Titanium Valve Retainers - Intake - Sold Each

T#:21604319

Part#: RET-BMN54-TI

Ships in 8 Business Days

$ 16.99 USD

Add to Wish List

Qty

$ 16.99 USD

Add to Wish List

7 Degree - 5mm valve stem - Single or Tripe Groove Valves

Performance Conical Valve Spring - Sold Each

T#:21604306

Part#: SPR-FE20BE-2

Ships in 8 Business Days

$ 20.99 USD

Add to Wish List

Qty

$ 20.99 USD

Add to Wish List

Supertech has the high performance valvetrain components you need to take your build to the next level. Seat Pressure: 84 @ 37 Open Pressure: 157 @ 10 Max Lift: 12.2mm Coil Bind: 23.20mm OutSpr.ID: 17.60mm InnSpr.OD: 21.00mm InnSpr.ID: 14.20mm Rate: 7.25

Show More Show Less

Supertech Single Groove Intake Valve - Priced Each

T#:14783497

Part#: BMIVN-1055S

Ships in 8 Business Days

$ 25.99 USD

Add to Wish List

Qty

$ 25.99 USD

Add to Wish List

Head Diam: 32mm (std) Material: Stainless Steel 21-4N Groove Type: Single Groove Length: 104.9mm Stem Diam: 4.97mm

Performance Conical Valve Spring - Set Of 24

T#:21604325

Part#: SPR-FE20BE-2-24

Ships in 8 Business Days

$ 494.99 USD

Add to Wish List

Qty

$ 494.99 USD

Add to Wish List

Supertech has the high performance valvetrain components you need to take your build to the next level. Seat Pressure: 84 @ 37 Open Pressure: 157 @ 10 Max Lift: 12.2mm Coil Bind: 23.20mm OutSpr.ID: 17.60mm InnSpr.OD: 21.00mm InnSpr.ID: 14.20mm Rate: 7.25

Show More Show Less

Supertech Titanium Valve Retainers - Exhaust - Sold Each

T#:21604320

Part#: RET-BMN54-TE

Ships in 8 Business Days

$ 16.99 USD

Add to Wish List

Qty

$ 16.99 USD

Add to Wish List

7 Degree - 6mm valve stem - Single or Tripe Groove Valves

Project Cars

SELECT YOUR BMW

BMW Internal Engine Parts for BMW 7 Series F02 (2009+)

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results