BMW Internal Engine Parts for BMW 7 Series F02 (2009+)

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:18733532

Part#: VTT-CRANKHUB-6

In Stock

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:18733525

Part#: VTT-CRANKHUB-3

In Stock

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - N54

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Spline Lock Crank Hub Solution

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Elring Cylinder Head Bolt Set - F01 F02 F10 F12 F13 E70 F15 F16 F85 F...

For vehicles with a production date from 10/2011

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:596417

Part#: 11127607557

Ships on Nov 17, 2026

$ 83.87

This product was last offered at the strikethrough price on
08-26-2026

$ 78.05 USD

Add to Wish List

Qty

$ 78.05 USD

Add to Wish List

OEM Ina Intake Hydraulic Tappet - BMW N52 N54 N55 N20 S55

Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply
We Price Match - Give Us A Call or Chat!

T#:591661

Part#: 11337548690

In Stock

$ 15.99 USD

Add to Wish List

Qty

$ 15.99 USD

Add to Wish List

Hydraulic valve lifter

Elring Cylinder Head Bolt Set - F01 F02 F10 F12 F13 E70 E71

For vehicles with a production date up to 10/2011

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:596414

Part#: 11127582454

Ships in 1 Business Day

$ 143.90

This product was last offered at the strikethrough price on
08-26-2026

$ 132.08 USD

Add to Wish List

Qty

$ 132.08 USD

Add to Wish List

One time use torque-to-yield cylinder head bolts. Always replace as a set whenever cylinder head is removed and reinstalled.

OEM INA Rocker Arm - BMW N20 2.0L, N52 N54 3.0L

Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:41492602

Part#: 11337559797

In Stock

$ 22.99 USD

Add to Wish List

Qty

$ 22.99 USD

Add to Wish List

Rocker arms work in conjunction with your camshafts and valves, applying pressure from the camshaft to open and close your intake and exhaust valves. If your rocker arm rollers have failed, this can lead to extreme camshaft damage, requiring the camshaft to be replaced. Replace your rockers whenever servicing your camshafts or replacing your hydraulic lifters to ensure long-term engine reliability.

Show More Show Less

Elring Cylinder Head Bolt Set - BMW N57 B57 3.0L

2X Entries Into Our F80 M3 Sweepstakes Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:44767341

Part#: 233.380

Ships on Dec 1, 2026

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

Cylinder head bolts need to be replaced after removal. Once a bolt is torqued down, you're unable to reuse it. This set of Elring cylinder head bolts is a great option to reattach your head to the block, without paying the markup for Genuine BMW parts. Replaces BMW p/n 11128513130, 11127812925, & 11128511621

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Internal Engine Parts for BMW 7 Series F02 (2009+)

Sub-Categories

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

N54 Spline Lock Crank Hub Solution With Complete Package

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

Spline Lock Crank Hub Solution W/ Hardware Package - N54

Vargas "Spline Lock" Crank Hub Solution - N54

Spline Lock Crank Hub Solution

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

Elring Cylinder Head Bolt Set - F01 F02 F10 F12 F13 E70 F15 F16 F85 F...

OEM Ina Intake Hydraulic Tappet - BMW N52 N54 N55 N20 S55

Elring Cylinder Head Bolt Set - F01 F02 F10 F12 F13 E70 E71

OEM INA Rocker Arm - BMW N20 2.0L, N52 N54 3.0L

Elring Cylinder Head Bolt Set - BMW N57 B57 3.0L

Select Vehicle

Purpose

Category

Brand

Price

Shipping

Narrow Results