BMW Maintenance & Tune-Up Parts for BMW 7 Series F02 (2009+)

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the current replacement for some BMW 6 and 8-cylinder engines built in the late 2000s and after. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. It's listed as a replacement coil for N20, N55, and S55 engines. In March 2015 BMW approved it for N51/N52 engines. This part number replaces the previous BMW part number 12137594937 for the cars listed below.

Sold per coil. Includes boot and connector.

Enhance your BMW's performance with the upgraded BAV Ignition Coil, designed to boost firepower and optimize engine efficiency. These coils boast modified core windings for a faster, more efficient burn, resulting in increased torque at lower RPMs and heightened horsepower in the upper range. While improvements depend on your engine's condition, these coils ensure noticeable enhancements in performance and potential fuel economy benefits.

Product Benefits:

Improved engine firepower and efficiency
Increased torque at lower RPMs
Enhanced horsepower in higher ranges
Potential improvement in fuel economy
Set of six for complete BMW Cooper replacement

Enhance your BMW's performance with the upgraded BAV Ignition Coil, designed to boost firepower and optimize engine efficiency. These coils boast modified core windings for a faster, more efficient burn, resulting in increased torque at lower RPMs and heightened horsepower in the upper range. While improvements depend on your engine's condition, these coils ensure noticeable enhancements in performance and potential fuel economy benefits.

Product Benefits:

Improved engine firepower and efficiency
Increased torque at lower RPMs
Enhanced horsepower in higher ranges
Potential improvement in fuel economy
Set of eight for complete BMW Cooper replacement

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!

The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.

K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top tier product for your European vehicle.

Features:

• Consistent filtering across entire filter surface
• Superior ASTMF316 filtration performance
• Magnetic Prefiltering
• Progressive rate bypass combined with high flow characteristics of the filter media avoids unfiltered oil bypassing the filter during cold startup and high rpm
• Easy inspection of engine contamination
• Proven in Motorsports, Military and Aerospace applications for years. Technology is FAA approved for use in aircraft. 

At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.

This part fits the following BMWs:
2012+ F30 3 Series Sedan 328i 328iX 328i 328iX 335i 335iX 
2006 - 2013 E9X 323i 325i 325xi 328i 328xi 330i 330xi 335i 335xi
2010 - 2016 F10 5 Series Sedan 528i 528iX 530i 535i 535iX 
2003 - 2006 E60 Sedan 525i 525xi 530i 530xi 
2007 - 2010 E60 528i 528xi 535i 535ix 
2009 - 2016 E89 Z4 Roadster Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i 
2014+ F22 2 Series Coupe 228i 228iX M235i M235iX
2007 - 2013 E88 1 Series Convertible 128i 135i
2008 - 2013 E82 1 Series Coupe 128i 135i 135is 1M Coupe
2012 - 2013 E70 X5 xDrive35d X5 xDrive35i
2007 - 2011 E70 X5 3.0sd X5 3.0si