BMW Engine Parts for BMW 7 Series F02 (2009+)

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

BMW Oil Cap Crankcase Breather - All BMW w/2 prong oil fill cap ...

2X Entries Into Our F80 M3 Sweepstakes

T#:558084

Part#: VTT-CRANK-BREATH

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

VTT N54 Crank Bolt Capture - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557938

Part#: VTT-N54-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice.

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

1x Aluminum Crank Bolt Capture
8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54

Show More Show Less

Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638889

Part#: VTT-CRANKGUARD

In Stock

Starting at $ 89.99 USD

Add to Wish List

Starting at $ 89.99 USD

Add to Wish List

It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Precision Raceworks Replacement Spark Plug Wires - Blue - Set of 6 - ...

T#:3786918

Part#: 201-0002

In Stock

$ 69.99 USD

Add to Wish List

Qty

$ 69.99 USD

Add to Wish List

The Precision Raceworks N54 N55 Manifold Location Replacement Spark Plug Wires are the same wires that come with Precision Raceworks' BMW N54 and N55 High Performance Ignition Kits, featuring low-resistance, high-performance spark plug wires. These wires are 100% custom-designed from the ground up to meet or exceed OEM requirements and feature seals that are both dust and water resistant. These spark plug wires work with Precision Raceworks' BMW N54 and N55 High Performance Ignition Kits 601-0021 or 601-0149.

Show More Show Less

Vargas Ignition Coil Kit (Red) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309610

Part#: VTT-COIL-N5X-RED

Ships in 1-2 days

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Vargas Burnt Titanium Magnetic Oil Drain Plug - M12 X 1.5

2X Entries Into Our F80 M3 Sweepstakes

T#:51813315

Part#: VTT-TI-DRAIN

In Stock

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

The VTT Burnt Titanium Magnetic Oil Drain Plug is a critical upgrade for any performance enthusiast looking to maximize engine longevity.

Precision Raceworks N54 N55 High Performance Ignition Kit - OEM Manif...

T#:1271579

Part#: 601-0021

Back Ordered

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

Rid your BMW's N54 or N55 engine of misfires, sluggish throttle response, rough idle, and power loss with Precision Raceworks' High-Performance Ignition Kit!

Vargas Ignition Coil Kit (Blue) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309605

Part#: VTT-COIL-N5X-BLU

Ships in 3 Business Days

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

VTT N54 Vacuum Pump Block Off Plate

2X Entries Into Our F80 M3 Sweepstakes

T#:11497328

Part#: VTT-N54-VACUUM-B

Ships in 6 Business Days

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

Looking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes Block Plate Note – Plates may come in a clear or anodize black finish depending on stock on hand

Show More Show Less

VTT BMW N54 “DI Injector” Delete Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:11497326

Part#: VTT-N54-DI-DELET

Ships in 1 Business Day

$ 339.99 USD

Add to Wish List

Qty

$ 339.99 USD

Add to Wish List

Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following 6 – 310 Stainless DI Delete fittings 3 – Hold down brackets Completetion of this kit will require the purchase of HPFP delete plate - ES# 4623950 PLEASE NOTE: THIS KIT REQUIRES EXTENSIVE MODIFICATIONS TO CONVERT YOUR ENGINE TO PI ONLY. THIS INCLUDES BUT IS NOT LIMITED TO A FULL PORT INJECTION SOLUTION, AND STAND-ALONE TO RUN THE PI SYSTEM. WE RECOMMEND THIS PNP SYSTEM USING THE MAXX ECU IT PROVIDES ALL YOU NEED TO GET UP AND RUNNING WITH PI ONLY ON THE TUNING SIDE OF THINGS – https://www.pnpecu.com/pnpecu-maxxecu-n54-pnp-kit-437-p.asp

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733525

Part#: VTT-CRANKHUB-3

In Stock

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Clear - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122266

Part#: VTTFILTERCAPCLR

In Stock

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Billet Check Valve - 10 Barb

2X Entries Into Our F80 M3 Sweepstakes

T#:597641

Part#: VTT-CHECK-2

Ships in 2 Business Days

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

BMW N54 3.0L Billet Vaccum Relief Valve

2X Entries Into Our F80 M3 Sweepstakes

T#:597525

Part#: VTT-VAC-RELIEF

Ships in 1-2 days

$ 104.99 USD

Add to Wish List

Qty

$ 104.99 USD

Add to Wish List

BMW N54 3.0L Billet Vacuum Relief Valve from Vargas Turbo Technologies offers precise control over crankcase vacuum levels. This high-quality billet valve allows users to adjust the vacuum pressure with ease, eliminating guesswork and ensuring optimal engine performance. By simply adding or removing shims, users can tailor the vacuum level to their needs.

Customizable Vacuum Levels: Adjust the vacuum pressure using supplied shims to achieve desired performance.
Direct Fit: Designed with -10ORB threads for easy installation into VTT modular PCV solutions and VTT Modular CNC valve covers.
Versatile Settings: Includes 5 vacuum settings ranging from 10' to 18' of vacuum based on shim configuration.
Enhanced Engine Protection: Helps prevent excessive vacuum that could affect engine seals or cause whistling.

Show More Show Less

Flapper Delete Fitting - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557962

Part#: VTT-FLAPPER-DELE

Ships in 10 Business Days

$ 57.99 USD

Add to Wish List

Qty

$ 57.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

The VTT PCV Flapper delete is used to get rid of the factory flapper, and add a -10 fitting on N54 powered vehicles. This will allow you to run a single or dual external catch can, or your own custom set up.

This fitting is made from 6061-T6 aircraft aluminum anodized black and comes with O-ring, and a stainless steel holding clip.

This part fits the following BMW engines:
2006-2012 N54

Show More Show Less

Multi-Pump Fuel Surge Tank (MPFST)

T#:31059457

Part#: 20-1440

In Stock at Vendor

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

BMW N54 3.0L Wastegate Rattle Fix Repair Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:398014

Part#: VTT-N54-WF2

Ships on Nov 10, 2026

$ 95.99 USD

Add to Wish List

Qty

$ 95.99 USD

Add to Wish List

VTT N54 Waste Gate Repair Kit / Rattle Fix Tired of the annoying N54 Wastegate Rattle? Turbos still going strong, but can't deal with the embarrassing rattle anymore? We have the perfect kit for you. This kit comes with 1 set (both turbos) of Stainless Steel wear matched bushing, and flapper assembly, Wastegate arm, rod end, and Stainless steel 8mm C clip. These parts custom made for VTT upgrade the flapper assembly to a full 12.6MM or 1/2" flapper arm, and bushing compared to the stock 11.5mm. They also get rid of the 6mm rod end connection to a full 8mm connection with a stainless steel C clip. There is no better N54 Waste Gate upgrade on the market, and guess what? We also offer them for less than other upgrades which use the stock bushing size, rod end, and inferior materials. If you want to fix this right the first time, this is the kit for you! *Please note, assembly is required. This kit can only be installed with the turbos removed from the vehicle, and stock wastegate assembly removed from the housing. The new assemblies will need to be pressed in, then welded by a qualified welder. We offer no warranty, or returns for improperly installed wastegate assemblies.

Show More Show Less

Billet 1/2" Check Valve - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557954

Part#: VTT-CHECK-1

Ships in 1 Business Day

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is a 1/2" (fits -8AN hos perfectly as well) CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run the vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.

This part fits the following BMW engines:
2006-2012 N54

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Red - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122280

Part#: TRIPLECAPRED1

In Stock

$ 209.99 USD

Add to Wish List

Qty

$ 209.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

TYC New Starter Motor

T#:1196068

Part#: 12412354701

Ships in 3 Business Days

$ 140.99 USD

Add to Wish List

Qty

$ 140.99 USD

Add to Wish List

Brand new unit - no core charge! Avoid messing with a core return entirely!

Precision Raceworks Replacement Spark Plug Wires - Stock Location - B...

T#:1271580

Part#: 201-0130

In Stock

$ 69.99 USD

Add to Wish List

Qty

$ 69.99 USD

Add to Wish List

Precision Raceworks' BMW N54 replacement spark plug wires are the same plug wires that are included in their High-Performance N54 Ignition Kit. These wires are 100% custom design from the ground up by Precision Raceworks, the only company in the world to produce plug wires with boots specific for your N54 BMW to ensure proper fitment and quality. Plug wires are sold in packs of 6 so you get all new plug wires every time. So, replace the one you need and keep the rest for spares or replace all 6. All components used meet or exceed OEM requirements and feature seals that are both dust and water-resistant.

Show More Show Less

Vargas Ignition Coil Kit (Black) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309609

Part#: VTT-COIL-N5X-BLK

Ships in 10 Business Days

$ 167.99 USD

Add to Wish List

Qty

$ 167.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Clear - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122281

Part#: TRIPLECAPCLR1

Ships in 10 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Blue - BMW N52 N5...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122267

Part#: VTTFILTERCAPBLUE

Ships in 10 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Red - BMW N52 N54...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122265

Part#: VTTFILTERCAPRED

In Stock

$ 89.99

This product was last offered at the strikethrough price on
10-05-2026

$ 80.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 89.99

This product was last offered at the strikethrough price on
10-05-2026

$ 80.99 USD

Limited Qty Sale

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Spline Lock Crank Hub Solution

2X Entries Into Our F80 M3 Sweepstakes

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

VTT N54 Wastegate Removal Tool

2X Entries Into Our F80 M3 Sweepstakes

T#:587520

Part#: VTT-WG-TOOL

Ships in 10 Business Days

$ 69.99 USD

Add to Wish List

Qty

$ 69.99 USD

Add to Wish List

Need to replace the wastegates on your N54 turbos, but do not have the tools to get the bungs out of the housings? This can be frustrating, and require sending your housings to a shop with a large press or make a puller. Vargas Turbo Technologies take the guesswork out of it for you by offering a tool that makes bung removal simple, and easy. Simply grind your old flappers off, and remove them from the bungs, then using the VTT tool the bung removal is a snap. Once out, you can reinstall the new bungs and have the flappers welded in the proper location. The tool is made from steel for high strength and long life. This tool is a must-have when doing wastegates on the N54 turbos! Tool kit comes the following: 1 Bung sleeve 1 Threaded removal arm 1 7/16"-14 3" bolt

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Black - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122279

Part#: TRIPLECAPBLK1

Ships in 10 Business Days

$ 220.99 USD

Add to Wish List

Qty

$ 220.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

VTT N54, N55, N20, B58 Billet Motor Mount Inserts

2X Entries Into Our F80 M3 Sweepstakes

T#:597676

Part#: VTT-INSERT-1

Ships in 1 Business Day

$ 178.99 USD

Add to Wish List

Qty

$ 178.99 USD

Add to Wish List

Instead of completely replacing the mount, simply make a billet aluminum insert for them. This leaves the feel of the factory mount in place but stiffens them up quite a bit removing unwanted engine movement without rattling your teeth out or emptying your wallet.

Show More Show Less

VTT Modular Cast Aluminum CNC Valve Cover Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:586044

Part#: VTTN54CASTVC-1-1

Ships in 10 Business Days

$ 759.99 USD

Add to Wish List

Qty

$ 759.99 USD

Add to Wish List

Billet N54 Valve Cover - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557949

Part#: VTTVCOVBCR

Ships in 10 Business Days

Starting at $ 1,448.99 USD

Add to Wish List

Starting at $ 1,448.99 USD

Add to Wish List

The N54 valve cover, while not a terrible design, has it's share of flaws. Most owners have had to replace this part over time as it can crack for seemingly no reason. Additionally, the stock valve cover has its limitations for vacuum and PCV connectivity.

VTT is proud to offer a ground-up system designed to give the end user complete control over their valve cover/ PCV set up. Tired of being told you will run two -10 lines from your VC to your Catch Can? Now you can run them any way you want! Including complete VTA, oil cap one-way breather, or whatever else you may need. This i a true solution that solves many plumbing headaches.

Accessability options aside, this part looks magnificent. CNC Machined and anodized in your choice or Red, Black, or Clear, this valve cover is sure to turn heads!

Details:

100% CNC 6061-T6 Aircraft aluminum construction
Anodized in a variety of colors
Custom logo available on the cap
Lightweight; 9.7 lbs. (compared to 7.9 lbs for a stock cover - only 1.8 lbs difference)
Gives the end user true variety for setting up their Valve Cover and PCV System

This part fits the following BMW engines:
2006-2013 N54

Show More Show Less

VTT CNC ORB Plug - -10AN

2X Entries Into Our F80 M3 Sweepstakes

T#:642075

Part#: VTT-10ORB

Ships in 10 Business Days

$ 23.99 USD

Add to Wish List

Qty

$ 23.99 USD

Add to Wish List

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Black - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122264

Part#: VTTFILTERCAPBLK

Ships in 10 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Single Turbo Fittings - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557947

Part#: VTT-SINGLE-FITTI

Ships in 8 Business Days

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

Going single on your N54 powered vehicle? You are going to have a few ports that need blocking on your motor. These fittings are just the ticket allowing you to block one or both of the water fittings on the block, block the rear drain, adapt the front drain for -10 AN, and convert your push in style feed to a 1/8"NPT to fit any number of fitting options.

All fittings are Made from 6061-T6 aircraft aluminum with black anodizing for a long-lasting finish and come with the O-ring needed.

This part fits the following BMW engines:
2006-2012 N54

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

VTT Turbocharger Inlet Flange - Garrett G40/42/45 V-Band - 86mm ID ...

2X Entries Into Our F80 M3 Sweepstakes

T#:52270240

Part#: GARROUTT4G4045

Ships in 10 Business Days

$ 37.99 USD

Add to Wish List

Qty

$ 37.99 USD

Add to Wish List

Upgrade your turbocharger exhaust connection with the VTT-FAB 86mm V-Band Outlet Flange, designed for the Garrett G40-G45 frame sizes.

Vargas Billet Valve Cover And Dual Catch Can Combo Kit - Billet Black...

2X Entries Into Our F80 M3 Sweepstakes

T#:22394048

Part#: VTTN54VCOCCBLK

Back Ordered

$ 2,129.99 USD

Add to Wish List

Qty

$ 2,129.99 USD

Add to Wish List

This convenient kit from Vargas includes everything you need, saving you the hassle of sourcing specific fittings for your valve cover-catch can setup. Spend less time searching and more time enjoying your upgraded system!

Show More Show Less

Black Market Parts Multi-Port Injection Kit - 750cc - BMW N54/N55 3.0...

T#:1316810

Part#: 601-0015

In Stock

$ 699.99 USD

Add to Wish List

Qty

$ 699.99 USD

Add to Wish List

If you plan on upgrading your turbos or increasing power in some other way, you will also want to consider upgrading your fueling capability as well! Using stock BMW injectors, you will likely top out at around 550rwhp on 93 Octane with water/methanol injection (or less if running an ethanol blend). At the end of the day, the stock injectors just are not enough. Introducing Black Market Parts (by Precision Raceworks) Multi-Port Injection Kit with flex-fuel compatibility! This kit allows you to safely and sufficiently support greater power levels with supplemental fueling without straining your stock fuel system. This kit integrates seamlessly into your car as if it were installed at the factory; you can’t even see the kit once the car is assembled! This kit includes everything needed to add multi-port injection and is 100% e85 compliant. Precision Raceworks includes new Genuine Bosch injectors which are flow matched both static and dynamic by an outside lab to industry-leading requirements. A Detailed certificate of conformance and genuine Bosch product certificate is included with each kit, giving you all flow data needed for optimal tuning. Don’t be tricked into thinking all port injection kits are equal, the BMP kit is the industry leader. This kit features 750cc* injectors standard (this flow rate is based on industry-standard injector flow test pressure of 43.5psi), and at 72psi these injectors flow over 1000cc. This means Precision's BMP Port Injection Kit is capable of supporting builds from 400whp up to 1,000whp and anywhere in between! Simply pick up this kit and pair it with your favorite injector controller and you are ready to go!

Show More Show Less

Precision Raceworks High Performance Ignition Kit - Black Coils - Sto...

T#:2869550

Part#: 601-0107

Ships in 9 Business Days

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

Rid your BMW's N54 of misfires, sluggish throttle response, rough idle, and power loss with Precision Raceworks' High-Performance Ignition Kit! Precision Raceworks' ignition kit is designed to fit any vehicle with an N54 engine and offers the highest output of any kit on the market! Featuring 100% Plug-&-Play connections, low resistance 50ohm/ft proprietary plug wires, and design technology from Marine and Aerospace applications, these coils are guaranteed to output consistent high voltage and current for optimal ignition system performance and reliability. Every component in this kit meets or exceeds OEM quality and features premium seals for dust and water resistance. While coils do not directly increase horsepower, stock BMW coils can wear out quickly, resulting in underperforming voltage and current output. This often leads to weaker spark intensity and reduced power output. Due to the increased voltage and current output, many customers have seen as much as 20+ whp/wtq gained by switching to Precision Raceworks coils over all other coils on the market! By upgrading to Precision's Performance Ignition Kit, spark quality can be restored and lost power regained, often with the additional power beyond what other coils provide. No software tune is required for installation or operation, but if desired, coil output can be increased to 118mJ from most software tuning companies!

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Blue - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122282

Part#: TRIPLECAPBLUE1

In Stock

$ 251.99

This product was last offered at the strikethrough price on
08-12-2026

$ 226.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 251.99

This product was last offered at the strikethrough price on
08-12-2026

$ 226.99 USD

Limited Qty Sale

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

Vargas Titanium Valve Cover Hardware Upgrade - Black - BMW B58, N55, ...

For vehicles with VTT Valve Cover

2X Entries Into Our F80 M3 Sweepstakes

T#:52129732

Part#: VTT-TI-BOLTS-2-B

Back Ordered

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

The VTT Titanium Valve Cover Hardware Kit is the ultimate finishing touch for your BMW N55, S55, or B58 engine.

Precision Raceworks High Performance Ignition Kit - Blue Coils - Stoc...

T#:1165722

Part#: 601-0020

Back Ordered

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

Rid your BMW's N54 of misfires, sluggish throttle response, rough idle, and power loss with Precision Raceworks' High-Performance Ignition Kit! Precision Raceworks' ignition kit is designed to fit any vehicle with an N54 engine and offers the highest output of any kit on the market! Featuring 100% Plug-&-Play connections, low resistance 50ohm/ft proprietary plug wires, and design technology from Marine and Aerospace applications, these coils are guaranteed to output consistent high voltage and current for optimal ignition system performance and reliability. Every component in this kit meets or exceeds OEM quality and features premium seals for dust and water resistance. While coils do not directly increase horsepower, stock BMW coils can wear out quickly, resulting in underperforming voltage and current output. This often leads to weaker spark intensity and reduced power output. Due to the increased voltage and current output, many customers have seen as much as 20+ whp/wtq gained by switching to Precision Raceworks coils over all other coils on the market! By upgrading to Precision's Performance Ignition Kit, spark quality can be restored and lost power regained, often with the additional power beyond what other coils provide. No software tune is required for installation or operation, but if desired, coil output can be increased to 118mJ from most software tuning companies!

Show More Show Less

VTT Stage 1 Turbocharger Upgrade - N63/N63TU

2X Entries Into Our F80 M3 Sweepstakes
There turbos are built to order. Please expect 4-6 weeks for delivery.

T#:11203241

Part#: VTTSTG1N63

Ships in 10 Business Days

Starting at $ 4,607.99 USD

Add to Wish List

Starting at $ 4,607.99 USD

Add to Wish List

This new rebuilt turbocharger unit utilizes Vargas Turbo's 30+ years of experience to offer a superior quality performance rebuild. Utilizing all-new internals to stock OEM specifications, the housings are carefully machined to accept custom-machined billet compressor wheels. Not only are these a superior choice for rebuilt turbos, they offer a substantial savings over OEM. Rebuilt stock turbos to handle up to 800 WHP Housings machined to accept custom-machined billet compressor wheels All-new internals to exacting stock specifications Includes $1300 refundable core charge Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost-effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

Show More Show Less

PCV Adapter Fitting N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557961

Part#: VTT-PCV-ADAPTER

Ships in 10 Business Days

$ 145.99 USD

Add to Wish List

Qty

$ 145.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is the adapter fitting that is required to convert your N54 to external PCV if you want to keep your crankcase under vacuum at idle, and anytime you have a vacuum condition in your intake manifold. They are made from 6061-T6 with black anodizing for a long-lasting finish. Includes complete adapter, with all o-rings, and retaining clip.

This must be used in conjunction with the Vargas billet check valve, and PCV delete fitting or requires plugging of the intake PCV ports. Installs inline on the throttle body, and adds a -8AN male to adapt to a catch cans, or any custom set up.

Made from 6061-T6 with black anodizing for a long-lasting finish. Includes complete adapter, with all o-rings, and retaining clip

This part fits the following BMW engines:
2006-2012 N54

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW 7 Series F02 (2009+)

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results