BMW Engine Parts for BMW 7 Series F02 (2009+)

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

BMW Oil Cap Crankcase Breather - All BMW w/2 prong oil fill cap ...

2X Entries Into Our F80 M3 Sweepstakes

T#:558084

Part#: VTT-CRANK-BREATH

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

VTT N54 Crank Bolt Capture - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557938

Part#: VTT-N54-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice.

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

1x Aluminum Crank Bolt Capture
8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54

Show More Show Less

Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638889

Part#: VTT-CRANKGUARD

In Stock

Starting at $ 89.99 USD

Add to Wish List

Starting at $ 89.99 USD

Add to Wish List

It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

VAC Motorsports Crank Seal Guard - N54 N55 S55

T#:29765724

Part#: VAC-11-CSG-N5X

Ships in 7 Business Days

$ 155.99

This product was last offered at the strikethrough price on
05-02-2026

$ 139.99 USD

Add to Wish List

Qty

$ 139.99 USD

Add to Wish List

The VAC Motorsports Crank Seal Guard, made of 6061 Billet Aluminum, prevents your serpentine belt from being pulled into your engine, a common problem amongst BMW N54, N55, and S55 Engines. Without a crank seal guard, the serpentine belt on N54, N55, and S55 engines is commonly sucked into the crank hub area past the crank seal, where it enters your engine and disrupts engine timing. When this occurs, the belt is shredded and clogs engine oil pickup, starving the engine and reducing oil pressure, causing catastrophic engine failure and thousands of dollars worth of damage. VAC Motorsports’ Crank Seal Guards are precision machined for perfect fitment and provide rigidity and maximum protection. We designed our guard with self-locating pilots to perfectly seal the crank hub bore and provide even, minimum clearance around the crank hub. Installation Hardware included. Made in the USA.

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Vargas Ignition Coil Kit (Red) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309610

Part#: VTT-COIL-N5X-RED

Ships in 1-2 days

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Vargas Burnt Titanium Magnetic Oil Drain Plug - M12 X 1.5

2X Entries Into Our F80 M3 Sweepstakes

T#:51813315

Part#: VTT-TI-DRAIN

In Stock

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

The VTT Burnt Titanium Magnetic Oil Drain Plug is a critical upgrade for any performance enthusiast looking to maximize engine longevity.

Vargas Ignition Coil Kit (Blue) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309605

Part#: VTT-COIL-N5X-BLU

Ships in 3 Business Days

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Valve Seal Repair Kit - Exhaust

T#:596691

Part#: 11340035853

In Stock

$ 22.99

This product was last offered at the strikethrough price on
10-13-2026

$ 22.75 USD

Add to Wish List

Qty

$ 22.75 USD

Add to Wish List

Burning oil at start-up and the first few minutes of running often is a sign your valve seals are bad. What happens is your valve seals become brittle and shrink up when cold, causing oil consumption and blue smoke from the exhaust. When the engine warms up, the seals expand, stopping the consumption.

Show More Show Less

Corteco Engine Mount - Left - F01, F02, F06, F07, F10, F12, F13 ...

T#:556259

Part#: 22116777365

In Stock

$ 83.99 USD

Add to Wish List

Qty

$ 83.99 USD

Add to Wish List

Replace your worn engine mounts

Corteco Engine Mount - Right - F01, F02, F06, F07, F10, F12, F13 ...

T#:556260

Part#: 22116786528

In Stock

$ 94.86

This product was last offered at the strikethrough price on
08-19-2026

$ 84.99 USD

Add to Wish List

Qty

$ 84.99 USD

Add to Wish List

Replace your worn engine mounts

VTT N54 Vacuum Pump Block Off Plate

2X Entries Into Our F80 M3 Sweepstakes

T#:11497328

Part#: VTT-N54-VACUUM-B

Ships in 6 Business Days

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

Looking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes Block Plate Note – Plates may come in a clear or anodize black finish depending on stock on hand

Show More Show Less

VTT BMW N54 “DI Injector” Delete Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:11497326

Part#: VTT-N54-DI-DELET

Ships in 1 Business Day

$ 339.99 USD

Add to Wish List

Qty

$ 339.99 USD

Add to Wish List

Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following 6 – 310 Stainless DI Delete fittings 3 – Hold down brackets Completetion of this kit will require the purchase of HPFP delete plate - ES# 4623950 PLEASE NOTE: THIS KIT REQUIRES EXTENSIVE MODIFICATIONS TO CONVERT YOUR ENGINE TO PI ONLY. THIS INCLUDES BUT IS NOT LIMITED TO A FULL PORT INJECTION SOLUTION, AND STAND-ALONE TO RUN THE PI SYSTEM. WE RECOMMEND THIS PNP SYSTEM USING THE MAXX ECU IT PROVIDES ALL YOU NEED TO GET UP AND RUNNING WITH PI ONLY ON THE TUNING SIDE OF THINGS – https://www.pnpecu.com/pnpecu-maxxecu-n54-pnp-kit-437-p.asp

Show More Show Less

ARP Performance Head Stud Kit - N54

T#:1061441

Part#: ARP-HSK-N54

Ships in 2 Business Days

$ 554.99 USD

Add to Wish List

Qty

$ 554.99 USD

Add to Wish List

Despite the fact that BMW engineers some of the worlds most revered engines, during number crunching something always has to be a compromise. One item that is always found to be a weak point- the OEM hardware. It is definitely sub-par for real performance use under high stress such as modded engines and track use. We use these fasteners on all of VAC's in-house head builds. Whenever the head is coming off, your switching to forced induction, or if you are simply prepping to drive your car hard; we highly recommend switching to far superior race-grade hardware. These Head Stud Kits greatly improve reliability; helping to eliminate movement of the of the cylinder head and intern, gasket failure caused by inferior OEM head-bolt stretch. This is the #1 cause of premature head gasket failure, especially on boosted or high output engines. Though more expensive than OEM, converting to one of VAC's head studs kits will not only give added strength and reliability when its needed most, but provides the most accurate torque readings because studs don’t “twist” into the block; all clamping forces are on one axis, and there is less force exerted on the normally stressed threads of the block. This increases block and hardware life and typically makes the head easier to properly install to the block, a blessing if your head may have to be removed more than once. Especially in the time crunch of racing, when engines are dissembled frequently, studs make removing and installing the cylinder head on to the block a much easier task. By allowing the studs to act as a guide on to the head, your head slides on and off and also ensures proper alignment of the head and gasket for the same reason. It is similar to converting your wheel-bolts to wheel-studs.

Show More Show Less

Valve Stem Seal Kit

T#:6366599

Part#: 11340039494

In Stock

$ 46.99

This product was last offered at the strikethrough price on
06-30-2026

$ 42.99 USD

Add to Wish List

Qty

$ 42.99 USD

Add to Wish List

N54 Spline Lock Crank Hub Solution With Complete Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733525

Part#: VTT-CRANKHUB-3

In Stock

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Crankshaft Seal - Front

T#:594913

Part#: 11117547842

In Stock

$ 21.99 USD

Add to Wish List

Qty

$ 21.99 USD

Add to Wish List

This seal needs to be replaced whenever a leak occurs, or whenever doing a timing chain service.

Corteco Rear Crankshaft Seal

T#:591494

Part#: 11117587168

Ships in 1 Business Day

$ 23.99 USD

Add to Wish List

Qty

$ 23.99 USD

Add to Wish List

90x110x8mm Replace your leaking crankshaft seal

Oil Pan Gasket for N52 N55 3.0L

T#:641949

Part#: 11137600482

In Stock

$ 43.99 USD

Add to Wish List

Qty

$ 43.99 USD

Add to Wish List

Ensure a leak-free BMW N52 or N55 3.0L engine with the Oil Pan Gasket. If you've noticed oil stains on your driveway, it could be a sign of a failing gasket. Replace it promptly to prevent further leaks and maintain the optimal performance of your BMW.

Leak Prevention: The Oil Pan Gasket effectively seals the oil pan, preventing oil leaks.
Common Leak Source: Addresses a common source of oil leaks in N52 and N55 3.0L engines.
Optimal Engine Performance: Ensures the engine operates without oil seepage, maintaining efficiency.
Easy Replacement: Ideal for DIY oil pan projects, making replacement hassle-free.

Upgrade your BMW's engine reliability with the N52/N55 3.0L Oil Pan Gasket, designed to keep your driveway oil-free.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Clear - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122266

Part#: VTTFILTERCAPCLR

In Stock

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

BMW N54 ARP Head Stud Kit

T#:17538610

Part#: ARP-HSK-N54-14

In Stock

$ 599.99 USD

Add to Wish List

Qty

$ 599.99 USD

Add to Wish List

The VAC Motorsports ARP Head Stud Kit was put together by VAC and ARP’s finest engineers. This is a completely custom kit designed specifically for the almighty N54. *High Boost (25+ psi application) option features: (14) 11mm ARP Head Studs (14) ARP Washers for 11mm Studs (14) ARP Nuts for 11mm Studs Install Tips: MUST drill and tap the (4) 9mm holes in the engine block to make them 11mm holes. This way all the engine block holes are 11mm, and fit ALL (14) 11mm Studs. Torque Specs: All studs torque down through 3-equal steps to 95 ft lbs ***This is NOT the Chrysler and Volvo stud kits! VAC Motorsports and ARP engineers designed and assembled this kit with high grade material, specifically so standard street-use or high-boost N54 owners have a PROPER kit that does not fail over time, such as the retro-fit Chrysler and Volvo head stud kits. ARP is the world leader in fastener technology. Makers of the finest fasteners in the market, especially for BMW engines, ARP is the brand you can count on when you want the highest reliability possible. If you are looking for high performance from your BMW engine, then ARP Head Stud Kits are a must. All kits come complete with hardened parallel-ground washers and aerospace-quality nuts.

Show More Show Less

Billet Check Valve - 10 Barb

2X Entries Into Our F80 M3 Sweepstakes

T#:597641

Part#: VTT-CHECK-2

Ships in 2 Business Days

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Meistersatz Valve Cover Gasket - E60, E61, E82, E88, E90, E92, E93, F...

T#:379628

Part#: 11127565286

In Stock at Vendor

$ 30.99 USD

Add to Wish List

Qty

$ 30.99 USD

Add to Wish List

Addresses valve cover leaks

BMW N54 3.0L Billet Vaccum Relief Valve

2X Entries Into Our F80 M3 Sweepstakes

T#:597525

Part#: VTT-VAC-RELIEF

Ships in 1-2 days

$ 104.99 USD

Add to Wish List

Qty

$ 104.99 USD

Add to Wish List

BMW N54 3.0L Billet Vacuum Relief Valve from Vargas Turbo Technologies offers precise control over crankcase vacuum levels. This high-quality billet valve allows users to adjust the vacuum pressure with ease, eliminating guesswork and ensuring optimal engine performance. By simply adding or removing shims, users can tailor the vacuum level to their needs.

Customizable Vacuum Levels: Adjust the vacuum pressure using supplied shims to achieve desired performance.
Direct Fit: Designed with -10ORB threads for easy installation into VTT modular PCV solutions and VTT Modular CNC valve covers.
Versatile Settings: Includes 5 vacuum settings ranging from 10' to 18' of vacuum based on shim configuration.
Enhanced Engine Protection: Helps prevent excessive vacuum that could affect engine seals or cause whistling.

Show More Show Less

Victor Reinz Crankshaft Seal - Front

For vehicles with a production date up to 02/2011

T#:374340

Part#: 11117547842

In Stock

$ 34.00

This product was last offered at the strikethrough price on
09-26-2026

$ 25.99 USD

Add to Wish List

Qty

$ 25.99 USD

Add to Wish List

65x79x10 - Usually replaced when servicing the timing chains

Flapper Delete Fitting - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557962

Part#: VTT-FLAPPER-DELE

Ships in 10 Business Days

$ 57.99 USD

Add to Wish List

Qty

$ 57.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

The VTT PCV Flapper delete is used to get rid of the factory flapper, and add a -10 fitting on N54 powered vehicles. This will allow you to run a single or dual external catch can, or your own custom set up.

This fitting is made from 6061-T6 aircraft aluminum anodized black and comes with O-ring, and a stainless steel holding clip.

This part fits the following BMW engines:
2006-2012 N54

Show More Show Less

Ferrea High Performance Valve Spring Kit for BMW N55/S55

T#:23416526

Part#: FER-HPVSK-N55

Ships in 3 Business Days

$ 1,049.99 USD

Add to Wish List

Qty

$ 1,049.99 USD

Add to Wish List

Maximize your N55 or S55 engine's performance with Ferrea Valve Springs and Retainers, precision components crafted from chromoly alloy. These springs undergo special thermal treatment, ensuring exceptional durability even in extreme racing conditions. Addressing issues like valve binding, breakage, and float, Ferrea valve springs are meticulously heat-treated and stress-relieved, providing stability for high-lift and high-RPM racing engines while minimizing load loss. Precision CNC machined titanium retainers offer superior strength and stability. Ferrea's Spring Seat Locators, made from 4140 chromoly alloy, guarantee precise tolerances and a flat, parallel spring pad with a hard Nitride surface treatment for exceptional toughness and anti-wear characteristics. Please note that installation requires the expertise of an engine builder.

Show More Show Less

Victor Reinz Intake Gasket Set - E70, E71, F01, F02, F06, F07, F10, F...

Two sets required per engine

T#:373815

Part#: 11617547242

Ships in 1 Business Day

$ 68.99

This product was last offered at the strikethrough price on
05-07-2026

$ 67.99 USD

Add to Wish List

Qty

$ 67.99 USD

Add to Wish List

1 for each intake runner 6 in total

BMW N54 3.0L Wastegate Rattle Fix Repair Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:398014

Part#: VTT-N54-WF2

Ships on Nov 10, 2026

$ 95.99 USD

Add to Wish List

Qty

$ 95.99 USD

Add to Wish List

VTT N54 Waste Gate Repair Kit / Rattle Fix Tired of the annoying N54 Wastegate Rattle? Turbos still going strong, but can't deal with the embarrassing rattle anymore? We have the perfect kit for you. This kit comes with 1 set (both turbos) of Stainless Steel wear matched bushing, and flapper assembly, Wastegate arm, rod end, and Stainless steel 8mm C clip. These parts custom made for VTT upgrade the flapper assembly to a full 12.6MM or 1/2" flapper arm, and bushing compared to the stock 11.5mm. They also get rid of the 6mm rod end connection to a full 8mm connection with a stainless steel C clip. There is no better N54 Waste Gate upgrade on the market, and guess what? We also offer them for less than other upgrades which use the stock bushing size, rod end, and inferior materials. If you want to fix this right the first time, this is the kit for you! *Please note, assembly is required. This kit can only be installed with the turbos removed from the vehicle, and stock wastegate assembly removed from the housing. The new assemblies will need to be pressed in, then welded by a qualified welder. We offer no warranty, or returns for improperly installed wastegate assemblies.

Show More Show Less

Billet 1/2" Check Valve - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557954

Part#: VTT-CHECK-1

Ships in 1 Business Day

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is a 1/2" (fits -8AN hos perfectly as well) CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run the vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.

This part fits the following BMW engines:
2006-2012 N54

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Red - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122280

Part#: TRIPLECAPRED1

In Stock

$ 209.99 USD

Add to Wish List

Qty

$ 209.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

Vargas Ignition Coil Kit (Black) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309609

Part#: VTT-COIL-N5X-BLK

Ships in 10 Business Days

$ 167.99 USD

Add to Wish List

Qty

$ 167.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Clear - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122281

Part#: TRIPLECAPCLR1

Ships in 10 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Blue - BMW N52 N5...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122267

Part#: VTTFILTERCAPBLUE

Ships in 10 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

CP Forged Piston Set - N63 - Pro-Xtreme 9.5:1

T#:26238409

Part#: CP-FPS-N63-XT-HD

Ships in 3 Business Days

$ 2,464.99 USD

Add to Wish List

Qty

$ 2,464.99 USD

Add to Wish List

The 5150 AutoSport Pro-Xtreme Forged Pistons, made by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW N63 engines. Constructed from high-strength, aircraft-grade steel, these pistons are engineered to withstand the forces generated by high-powered engines. The Pro-Xtreme Piston design is specifically engineered to handle up to 2000 horsepower, making these pistons suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each piston is precisely fabricated to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Pistons are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines. Includes: - Pistons - HD Wrist Pins - PVD Rings - Pins - Locks - Spec Sheet

Show More Show Less

Victor Reinz Cylinder Head Bolts - N54

T#:373825

Part#: 11127574303

Ships in 1 Business Day

$ 147.99

This product was last offered at the strikethrough price on
10-12-2026

$ 134.99 USD

Add to Wish List

Qty

$ 134.99 USD

Add to Wish List

Head Bolt set for the N54 engines with aluminum block.

If you drive a European vehicle, chances are high your vehicle came equipped with one or more Victor Reinz gaskets. Choose OE quality VR gaskets and seals and do the job right the first time.

Show More Show Less

CP-Carrillo Pro-Xtreme Connecting Rod Set - BMW N63/S63

T#:23681818

Part#: CAR-CRS-S63-XTT

Ships in 3 Business Days

$ 2,999.99 USD

Add to Wish List

Qty

$ 2,999.99 USD

Add to Wish List

Tailored for exceptional performance, the Pro-Xtreme design is crafted to handle up to 2000 horsepower and 9500 RPM. Constructed from high-strength, aircraft-grade steel, these connecting rods feature a tapered small-end, allowing them to be paired with your OEM pistons.

Show More Show Less

Performance N55 Main Bearing Set

T#:26238415

Part#: 5150-HPMBS-N55

Ships in 3 Business Days

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

5150 High Performance Coated Main Bearing Sets are made for the demands of high performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

Victor Reinz Valve Seal Repair Kit - Exhaust

T#:377137

Part#: 11340035853

Ships in 2 Business Days

$ 58.99 USD

Add to Wish List

Qty

$ 58.99 USD

Add to Wish List

Stop burning oil at start-up

Vargas "Spline Lock" Crank Hub Solution - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

BMW N55 S55 Ferrea High Performance Valve Kit

T#:23416508

Part#: FER-HPVK-S55-T-3

Ships in 3 Business Days

$ 929.99 USD

Add to Wish List

Qty

$ 929.99 USD

Add to Wish List

Increase the power output of your N55/S55 engine with the high-performance Ferrea valve kit. Renowned as the industry's most reliable extreme-duty valves, they're meticulously crafted from aerospace-grade alloys, employing an exclusive two-step slow forging process for optimal grain flow and material structure integrity. A 48-hour heat treatment and stress-relieving process enhance molecular integrity. The valves feature avionics-quality hard chrome and a specially applied hard tip. Standard size: 32mm intake / 28mm exhaust, with a triple groove valve design. Compatible with factory valve locks ("Valve Keepers"), the kit includes 12x Intake Valves and 12x Exhaust Valves for a comprehensive engine upgrade!

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Red - BMW N52 N54...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122265

Part#: VTTFILTERCAPRED

In Stock

$ 89.99

This product was last offered at the strikethrough price on
10-05-2026

$ 80.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 89.99

This product was last offered at the strikethrough price on
10-05-2026

$ 80.99 USD

Limited Qty Sale

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Timing Cover Output Shaft Seal

T#:594929

Part#: 11147647380

Ships in 1 Business Day

$ 42.19

This product was last offered at the strikethrough price on
08-07-2026

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Seals the timing case on the front of the engine

VTT N54 Wastegate Removal Tool

2X Entries Into Our F80 M3 Sweepstakes

T#:587520

Part#: VTT-WG-TOOL

Ships in 10 Business Days

$ 69.99 USD

Add to Wish List

Qty

$ 69.99 USD

Add to Wish List

Need to replace the wastegates on your N54 turbos, but do not have the tools to get the bungs out of the housings? This can be frustrating, and require sending your housings to a shop with a large press or make a puller. Vargas Turbo Technologies take the guesswork out of it for you by offering a tool that makes bung removal simple, and easy. Simply grind your old flappers off, and remove them from the bungs, then using the VTT tool the bung removal is a snap. Once out, you can reinstall the new bungs and have the flappers welded in the proper location. The tool is made from steel for high strength and long life. This tool is a must-have when doing wastegates on the N54 turbos! Tool kit comes the following: 1 Bung sleeve 1 Threaded removal arm 1 7/16"-14 3" bolt

Show More Show Less

CP-Carrillo Connecting Rod Set - N63/S63 Pro-Xtreme

For Use With Aftermarket Pistons Only!

T#:26238404

Part#: CAR-CRS-S63-XT

Ships in 3 Business Days

$ 2,899.99 USD

Add to Wish List

Qty

$ 2,899.99 USD

Add to Wish List

5150 AutoSport Pro-Xtreme Connecting Rods, manufactured by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW N63 and S63 Engines. The Pro-Xtreme design is specifically tailored to handle up to 2000 horsepower, making them suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each connecting rod is precisely engineered to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Connecting Rods are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines.

Show More Show Less

Victor Reinz Valve Seal Repair Kit - Intake

T#:377087

Part#: 11340034068

Ships in 2 Business Days

$ 54.99

This product was last offered at the strikethrough price on
05-07-2026

$ 39.99 USD

Add to Wish List

Qty

$ 39.99 USD

Add to Wish List

Seal fitted to the end of the valve

Spline Lock Crank Hub Solution

2X Entries Into Our F80 M3 Sweepstakes

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW 7 Series F02 (2009+)

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results