Valve Cover for BMW 5 Series F10 (2011-2016)

Valve Cover Gasket Overhaul Kit - E9X 328i, E60 528i, E83 X3 3.0i/si,...

T#:180875

Part#: TMS180875

In Stock

$ 142.24

This product was last offered at the strikethrough price on
05-07-2026

$ 107.33 USD

Add to Wish List

Qty

$ 107.33 USD

Add to Wish List

Not only will this kit stop most E90 oil leaks, it's the perfect addition for ignition coil or spark plug replacement! Oil leaks - and the damage they can cause - seem to be the worst annoyances on these cars. The biggest source of an oil leak is from the valve cover, followed by the oil filter housing, Valvetronic seal, camshaft seals, and the eccentric shaft sensor seal. Once the oil leaks, and if ignored for an extended time, the oil will contaminate vital electrical sensors. This is especially the case with ignition coils and also the eccentric shaft sensor on the Valvetronic shaft at the top of the cylinder head. During any ignition coil and spark plug replacement take a close look inside for any oil pooling at the bottom. We have been seeing valve cover oil leaks as soon as 40,000 miles. We look for oil leaks on every E90 that comes into our shop.

We have put together this package of valve cover gaskets and other related gaskets and seals for you to fully overhaul the N52 valve cover and put a stop to those pesky oil leaks. This package has the replacement parts for N52 engines built from the 2007 model year and includes:

11127582245 - N52 valve cover gasket set
11127552280 - N52 eccentric shaft sensor seal
11127559699 - N52 Valvetronic gasket

2007 and later N51/N52 engines do not need replacement valve cover bolts, unless the bolts are actually broken off or missing. Unlike the 2006 aluminum hardware, the later parts are steel and not 1-time use.

These are all OEM or OE parts. Replacement of these gaskets and seals is straight-forward but a long process. BMW dealers typically charge for over eight hours of labor. If you have replaced spark plugs before you should be capable of this repair. In addition, there are several other parts to replace while you're in the vicinity: camshaft sensor o-rings, oil filter housing profile gasket, VAN0S solenoids, and the eccentric shaft sensor. These other parts, except the eccentric shaft sensor (see below), are replaceable without removing the valve cover but are more easily accessed during the valve cover work.

Eccentric Shaft Sensor: This is the position sensor that relays the eccentric shaft's position back to the DME. It's located at the front of the engine and is only accessible with the valve cover off . The seal around the sensor can fail and allow oil to blow out from under the cam cover. Oil can then leak into the sensor itself and cause it to fail. Without a functioning sensor your E90 can experience poor running, hesitation, poor performance, jerky shifts, and sluggish response. It's easy to check and see if oil has accumulated inside the sensor: unbolt the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside or even around the sensor itself, plan on replacing this sensor during your next ignition coil, spark plug, and/or valve cover gasket work.

This valve cover kit fits the following BMWs:
2008-2012 E82 BMW 128i
2007-2011 E90 BMW 328i 328xi 328i xDrive - Sedan
2007-2012 E91 BMW 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2007-2010 E60 BMW 528i 528xi 528i xDrive
2011 F10 BMW 528i
2007-2010 E83 BMW X3 3.0i X3 3.0si
2007-2013 E70 BMW X5 3.0si
10/2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive30i

Show More Show Less

Valve Cover Gasket - Set

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:586660

Part#: 11127587804

In Stock

$ 22.99 USD

Add to Wish List

Qty

$ 22.99 USD

Add to Wish List

Valve Cover Kit - N55

T#:5376284

Part#: 11127570292TKT

In Stock

Sale - Save 5% $ 320.99

This product was last offered at the strikethrough price on
05-03-2026

$ 304.52 USD

Add to Wish List

Qty

Sale - Save 5%

$ 320.99

This product was last offered at the strikethrough price on
05-03-2026

$ 304.52 USD

Add to Wish List

If your valve cover has become cracked or warped, replace it with this Hamburg Tech cover from Turner Motorsport to prevent leaks and further valvetrain damage. Replace your leaking valve cover to keep your oil inside the engine, where it belongs. Includes everything needed to install a new valve cover: Valve cover Gasket flange Crank case vent hose Hardware

Show More Show Less

BMW Valve Cover - N55 3.0L

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:591543

Part#: 11127570292

In Stock

$ 226.86 USD

Add to Wish List

Qty

$ 226.86 USD

Add to Wish List

BMW Valve Cover - N55 3.0L is a high-quality direct replacement designed to restore the reliability and performance of BMW’s turbocharged N55 engine. Manufactured by URO Parts, this valve cover meets strict ISO 9000 certification standards, ensuring durability and precise fitment. Engineered to prevent common issues such as oil leaks and vacuum loss, it is an essential component for maintaining engine efficiency.

Direct replacement for OEM valve covers, ensuring a seamless installation
ISO 9000 certified manufacturing for long-lasting reliability and quality
Prevents oil leaks and vacuum loss, improving engine efficiency
Durable construction designed to withstand high temperatures and engine vibrations
Compatible with BMW N55 3.0L engines, offering an exact fit for select models

Ensure peak engine performance and reliability by replacing a worn or cracked valve cover with this premium-quality URO Parts component.

Show More Show Less

URO Valve Cover Kit - E82 128i, E9X 328i, E60 528i, E70 X5 3.0si, E83...

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat! For 2007+ models with plastic valve cover

T#:395230

Part#: 11127552281

Ships in 1 Business Day

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

All-in-one valve cover overhaul Preventative replacement saves time and trouble later on Includes new oil separator system Replace valve cover gaskets before a leak becomes worse Replace valve cover before it cracks For the 2007 model year BMW switched to a plastic valve cover on the N51 and N52 engines. As we have seen over time the plastic can crack which leads to oil leaks, vacuum leaks, poor running, and other issues. Unfortunately, it's not just the gasket that needs periodic replacement but the entire valve cover itself. This kit includes a new valve cover, gaskets, eccentric shaft seal, and hardware. The valve cover also incorporates the oil separator which is not a replaceable item on its own. So a complete valve cover replacement will tackle multiple problem areas at once. The valve cover is the same for N51 SULEV and N52 engines. Cracked Valve Cover. The plastic used for the N52 valve cover is thin and weak in certain spots. This makes it prone to hairline or larger cracks that will leak oil and cause vacuum leaks. You might also notice rough running, especially at idle. Often a technician will go looking for a failed ignition coil, spark plug, or failed vacuum hose on the engine. And without a fault code to assist in diagnosis this can often mean wasted time and money. A cracked valve cover is a new problem area that many techs don't think to check. Oil Separator/Crankcase Vent. BMW integrated the oil separator system into the valve cover on these later engines. An internal manifold creates a cyclone effect and centrifugal force separates vapor from the liquid oil. The liquid oil is supposed to drain through the valve cover and back to the oil pan while the remaining vapor is burned up during combustion. It's a very efficient and environmentally-friendly design with very few moving parts. Unfortunately it's not perfect and eventually the internal passageways will become clogged. This problem is made worse in cars that have short drive cycles, sit for long periods of time, do not have frequent oil changes, do not see regular runs to redline, and cars in freezing climates. If the engine never reaches optimal operating temp the oil remains in liquid form or becomes sludge. This is bad news for the entire engine, leading to fouled spark plugs, rough running and misfires and even premature failure of catalytic converters and oxygen sensors. Since the oil separator system in the valve cover is not available on its own, and cleaning it is nearly impossible, the complete replacement of the valve cover is the only option. Other oil vent tubes and vacuum hoses are also recommended to get replaced at the same time. Valve Cover Gaskets. As with any rubber part, failures occur when the rubber becomes dry and brittle. The pliable rubber no longer forms a seal between the cylinder head and valve cover where it will develop an oil leak. Valve cover gaskets that leak can allow oil to seep into the spark plug holes and contaminate ignition coil boots and plugs. That can lead to rough running and misfires. A new valve cover includes new gaskets. Eccentric Shaft Seal. The seal for the eccentric shaft sensor is a known spot for oil leaks. When the seal to the valve cover fails oil can end up in the sensor itself and ruin the sensor (an unecessary $300 expense). Usually a new seal (o-ring) will stop the leaks but sometimes the valve cover is at fault too. A new eccentric shaft seal is included. All new hardware is included to avoid re-using and over-tightening the original bolts (they have a very low torque rating). Replacement requires accessing the rear of the engine with a lot of the upper plastic shrouding removed. The vent hose on the valve cover should be replaced as it is almost always broken anyway (#11157559528). The metal fuel line must also be removed and disconnected from the fuel injectors. Professional installation is encouraged if you have never done this kind of work before. Serious DIY types should have a Bentley Service Manual to use which greatly explains the process. You may also want to combine this work with the oil filter housing gasket replacement. There is no maintenance or replacement interval for the N52 valve cover. However, we have seen cracks and other failures in the 50,000-90,000 mile range. Our best advice is to plan on a major top end overhaul around the 70-80,000 mile mark. There's no mechanical downside to replacing it as prevention and it will make the engine run better and last longer. This item fits the following BMWs: 2008-2012 E82 BMW 128i 2007-2011 E90 BMW 328i 328xi 328i xDrive - Sedan 2007-2012 E91 BMW 328i 328xi 328i xDrive - Wagon 2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe 2007-2013 E93 BMW 328i - Convertible 2008-2010 E60 BMW 528i 528xi 528i xDrive 2011 F10 BMW 528i 2007-2010 E83 BMW X3 3.0i X3 3.0si 2007-2008 E70 BMW X5 3.0si 2007-2008 E85 BMW Z4 3.0i Z4 3.0si 2009-2010 Z4 BMW Z4 sDrive30i

Show More Show Less

Valve Cover Gasket Kit - BMW N20

T#:30164647

Part#: 11127507217KT2

Ships in 1 Business Day

$ 73.99 USD

Add to Wish List

Qty

$ 73.99 USD

Add to Wish List

Maintaining proper oil levels in your engine is crucial for peak performance. Undetected leaks can cause your oil to drop to dangerously low levels between oil changes, leading to severe engine damage.

One common culprit for oil leaks is the valve cover. Over time, exposure to extreme temperature fluctuations can wear down the gaskets, causing them to fail. Prevent oil leaks and protect your engine by replacing these vital components.

Comprehensive Kit Includes:

Valve Cover Perimeter Gasket Vacuum Pump Seal Valvetronic Actuator Seal HPFP Screws (2) Replace your old gaskets with our high-quality kit to keep your engine running smoothly and efficiently.

Show More Show Less

Comprehensive Valve Cover Gasket Kit - N63/S63

T#:30164665

Part#: 11128648131KT2

Ships in 1 day

$ 150.99

This product was last offered at the strikethrough price on
04-06-2026

$ 145.99 USD

Add to Wish List

Qty

$ 145.99 USD

Add to Wish List

Maintaining proper oil levels in your engine is crucial for peak performance. Undetected leaks can cause your oil to drop to dangerously low levels between oil changes, leading to severe engine damage.

One common culprit for oil leaks is the valve cover. Over time, exposure to extreme temperature fluctuations can wear down the gaskets, causing them to fail. Prevent oil leaks and protect your engine by replacing these vital components.

Comprehensive Kit Includes:

Valve Cover Gasket Set - Left & Right High Pressure Fuel Pump Gasket (2) O-Ring Seals (6) Torx Screws (6) Replace your old gaskets with our high-quality kit to keep your engine running smoothly and efficiently.

Show More Show Less

URO Cylinder Head Cover - ZYL 1-4

T#:50031876

Part#: 11127588545

Ships in 1 Business Day

$ 449.99 USD

Add to Wish List

Qty

$ 449.99 USD

Add to Wish List

Replacement for broken valve cover.

Valve Cover Bolt - Priced Each

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:32781449

Part#: 11129454322

In Stock

$ 9.59 USD

Add to Wish List

Qty

$ 9.59 USD

Add to Wish List

URO Valve Cover Bolt - BMW

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:32781448

Part#: 11127584156

In Stock

Sale - Save 12% $ 9.99

This product was last offered at the strikethrough price on
05-15-2026

$ 8.84 USD

Add to Wish List

Qty

Sale - Save 12%

$ 9.99

This product was last offered at the strikethrough price on
05-15-2026

$ 8.84 USD

Add to Wish List

Replace your stripped or missing valve cover bolt to ensure a tight seal of the valve cover to the cylinder head. Guaranteed fitment Broken valve cover bolts can create troublesome vacuum leaks and allow leaking oil to damage engine components URO valve cover bolts are precisely manufactured to OE dimensions for easy installation and secure attachment Durable high-quality material withstands oil vapor and intense engine heat 24-Month Unlimited Mileage Warranty

Show More Show Less