BMW Fuel System Parts for BMW F87 M2 N55 3.0L

Clear BMW chassis

Looking for a BMW fuel pump, BMW gas cap or other BMW fuel system related items? You've found the right place. Your BMW fuel delivery system is a critical system, and any failure can rended your BMW dead in the water. Whether your fuel pump has stopped pumping, a fuel injector is clogged or not spraying, or your gas cap is either lost or not properly sealing, we likely have what you are looking for. We stock thousands of BMW fuel system parts so if you don't see what you are looking for, just give us a call.

Sub-Categories

Sort By:

Port Injector Plugs

T#:27171925

Part#: UNI-BMS-PIPLUGS

In Stock

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

These dummy injectors fit in place of port injection fuel injectors to block the holes. Allows use to aluminum manifolds with port injection bungs without having to purchase fuel injectors. Plugs are EV14 injectors and measure 38mm or 1.5" from o-ring to o-ring.

Show More Show Less

BM3 FlexFuel Kit - OEM Fuel Hat Location - BMW F-Series S55/N55 3.0L ...

T#:33746522

Part#: BM3FFKTF55

Ships on Sep 16, 2026

$ 599.00 USD

Add to Wish List

Qty

$ 599.00 USD

Add to Wish List

We are proud to bring out this truly awesome product that makes getting the required Flex Fuel hardware on your BMW and A9X Supra with incredible ease and minimal effort, in your own driveway.

Our kit is entirely plug-and-play with the factory vehicle harness. No cutting or splicing of OEM wiring/connectors. It installs in minutes and can be removed without a trace on the car!

Our team used SolidWorks to design a Flow Optimized Flex Fuel Sensor Adapter (FFSA) to ensure fuel flow is unobstructed and with no added pressure drop at full fuel pump flow from the fuel tank to your motor when our kit is installed. This is important when pushing the factory fuel system with all the power Ethanol can provide over petrol!

Flex fuel sensor housing is designed to neatly install into the factory BMW fuel hat location.

Flex Fuel Sensor Adapter also contains two 1/8 NPT ports that allow installation of an auxiliary Fuel Pressure sensor for vehicles that don’t come with an OEM one from the factory for future use. Depending on fitment, either port can be used.

Install the bootmod3 Flex Fuel Plug and Play Kit and flash your flex fuel enabled bootmod3 OTS MultiMap or Custom Map in minutes and you’re off to the races never worrying about alcohol/petrol blend % in your fuel tank. It does not get better or easier than this!

bootmod3 FlexFuel Plug and Play Kit:

Minutes to install at home as opposed to hours at a shop with car up on lift fabricating/cutting into factory fuel lines and splicing/cutting/pinning into OEM electrical
4+ hours in time/cost savings to get going on Flex Fuel as compared to most other kits that require making custom fuel lines, fittings and custom wiring!
Fully reversible/removable and back to stock without a trace in minutes
Custom 3-piece Aluminum-6061 Flex Fuel sensor adapter with built-in sensor bypass to allow for obstruction free fuel flow made to fit in the vehicle factory fuel hat area below the rear seat
All connecting points sealed with fuel safe Viton o-rings
Flex Fuel Sensor Adapter housing provides additional 1/8 NPT ports for optional Fuel Pressure sensor addition to vehicles without a factory one for bootmod3 CustomROM v2 support
CANBUS Enabled Ethanol Content Analyzer (ECA) that integrates with bootmod3 CustomROM for complete and seamless conversion of your BMW to FlexFuel for bootmod3 Flex Fuel enabled OTS MultiMaps and custom tunes with your bootmod3 tuner of choice
Power/CANBus 4-wire plug and play harness
- 100% Fully Plug and Play harness to the BMW Fuel Controller connectors (EKP3) on S55, N55 vehicles
- 100% Fully Plug and Play harness on the BMW Body Domain Controller (BDC/FEM) connector on Gen1 F-series B48/B58
Continental Flex Fuel sensor 3-wire harness
Custom Aluminum-6061 CANBus Enclosure for the bootmod3 ECA board
Custom, kink-free teflon braided line allowing plug and play installation with the OEM fuel hat and factory 5/16” or 3/8” fuel feed line. No cutting or new lines required.
-6 AN fitting by Racetronix

OEM FUEL HAT LOCATION KIT IS INTENDED FOR OEM FUEL PUMP AND ASSOCIATED WIRING. ANY VARIATIONS TO FUEL LINES OR FUEL PUMPS MAY NOT BE COMPATIBLE. USE THE ENGINE BAY INSTALLATION KIT WHERE AVAILABLE INSTEAD.

Show More Show Less

Race German Inline Fuel Pressure Adapter (1/8npt)

T#:7703242

Part#: RGIFPA

Ships in 2 Business Days

$ 23.99 USD

Add to Wish List

Qty

$ 23.99 USD

Add to Wish List

Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. Finding a way to measure your fuel pressure is not always the easiest thing to do. Race German wanted to make your life just a little easier with this in-line fuel pressure adapter. This simple solution allows you to splice into your rubber fuel feed line hose and attach a 1/8NPT pressure sender. This would be great to run a fuel pressure gauge, or give you a way to temporarily test your pressure for troubleshooting issues, either way you can't go wrong. *Does not include pressure sender.

Show More Show Less