Turbo Install Kits

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos! 

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

Going single on your N54 powered vehicle? You are going to have a few ports that need blocking on your motor. These fittings are just the ticket allowing you to block one or both of the water fittings on the block, block the rear drain, adapt the front drain for -10 AN, and convert your push in style feed to a 1/8"NPT to fit any number of fitting options.

All fittings are Made from 6061-T6 aircraft aluminum with black anodizing for a long-lasting finish and come with the O-ring needed.

This part fits the following BMW engines:
2006-2012 N54

Upgrade your BMW B58 engine with the VTT GC-MID Stock-650WHP (TU ONLY) turbocharger for unparalleled performance gains. VTT's turbocharger offers easy installation, eliminating core charges and long lead times associated with traditional upgrades. With enhanced design elements and OE-quality castings, this turbocharger supports over 600WHP while maintaining factory spool and connections.

• All-new castings with factory restrictions removed
• Full 3' turbocharger inlet size with included silicone inlet elbow
• 9-blade turbine and compressor wheels for increased flow and spool
• Direct connection to all factory lines
• Redesigned internal components for improved performance
• No core charges and no long lead times
• Full 12-month unlimited mileage warranty