Find Parts That Fit Your Vehicle

Engine Hardware

Most engine hardware including head studs, VANOS bolts, and exhaust studs can only be used once. While most of the accessory bolts and miscellaneous hardware can be re-used it is often handy to have a spare bolt or bracket just in case one breaks. Any aluminum bolt, such as those found in the N52 engine MUST be replaced no matter the age or visual condition.

Sort By:

Athena Cut Ring Head Gasket - 84.5mm - BMW M50 M52 (84mm Bore) ...

T#:26171655

Part#: ATH-HG-CR-M50-84

Ships in 7 Business Days

$ 324.99 USD

Add to Wish List

Qty

$ 324.99 USD

Add to Wish List

Upgrade your BMW engine's performance with the Athena Cut Ring Head Gasket. This gasket replaces BMW part # 11121726619 and 11121726617 and is specifically designed for M50 & M52 iron block inline 6-cylinder engines found in E34/E36 chassis. Standard OEM & MLS gaskets can only handle a certain amount of cylinder pressure before they start to leak, making the Athena Cut Ring Head Gasket the recommended choice for applications making 16+ psi. A compression leak passing the head gasket can cause a range of issues, including engine overheating, loss of power, misfires, and in severe cases, catastrophic engine failure. Athena's gasket is crafted with premium quality reinforced M0115, an asbestos-free material that's original equipment approved and renowned for its superior quality. The AISI 304 stainless steel Cooper Rings bite into the aluminum head, providing maximum sealing capabilities around the cylinder bore and optimizing engine performance, even on engines with nitrous and/or turbo applications that exceed 2-bar boost. Before installation, it is crucial to have the mating surfaces of the cylinder head and block professionally cleaned and resurfaced to ensure they are completely flat. Please be aware that the gasket should have a size that is 0.5mm to 1mm larger than the piston. For example, if the piston measures 84mm, then the gasket should be the next size up, either 84.5mm or 85mm. Installation instructions: Make sure that the engine block and cylinder head surfaces are clean, flat, and free from any debris, oil, or coolant. Install the Cut Ring gasket on the engine block and ensure that it is properly aligned. Avoid twisting or bending the gasket during installation. Place the cylinder head on top of the gasket and install the head bolts or studs in their correct positions. Follow the manufacturer's recommended torque specifications and tighten the bolts or studs in the proper sequence to ensure even clamping force across the gasket. After the initial tightening, re-torque the head bolts or studs after the engine has been started and then allowed to cool to room temperature. This will ensure that the gasket is properly seated and compressed. It is recommended to not use any additional sealant on the MLS gasket, as it is already coated with a Viton rubber sealant. Using additional sealant can hinder the performance of the gasket.

Show More Show Less

407 Piece O-Ring Assortment

T#:1809147

Part#: W5202

In Stock at Vendor

$ 21.99 USD

Add to Wish List

Qty

$ 21.99 USD

Add to Wish List

Nitrile Butadiene Rubber

Blue Thermostat Caps (pair)

T#:54139632

Part#: BMS-TCP-BLU

Ships in 1 Business Day

$ 29.00 USD

Add to Wish List

Qty

$ 29.00 USD

Add to Wish List

Billet Oil Thermostat Lid

T#:21045480

Part#: BMS-TLID

In Stock

Starting at $ 39.00 USD

Add to Wish List

Starting at $ 39.00 USD

Add to Wish List

These billet CNC replacement aluminum oil thermostat lids and caps are an excellent way to add some color and style to your N54 N55 S55 engine bay. Anodized black, red or blue. Easy to install and made in the USA. Can be used with or without the BMS Sport Oil Cooler Valve.

Show More Show Less

Burger Motorsports Turbo Double Baffle Oil Catch Can - F23 235i Conve...

T#:5567062

Part#: OCCN55-235VERT

Ships on Oct 27, 2026

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

It's no secret that BMW turbo motors can suffer from oil control problems causing oil to blow through and coat the intercooler and charge piping, gunking up intake valves and the VANOS system, lowering the effective octane, and generally degrading engine performance. The higher your boost levels the more apparent these problems become. The solution to this problem has finally arrived. The BMS oil catch can. While there are other catch cans on the market they all fall short in various areas. Some are mounted on the hot/turbo side of the motor preventing proper vapor condensation. Others utilize hoses that are too small and runs that are too long to allow proper PCV ventilation causing internal motor/ring sealing issues. Some have insufficient or no internal baffle system while others have internal baffles systems that are too restrictive. Some even bypass the PCV system all together venting crankcase gas and odor to the atmosphere. Most are simply repackaged oil catch cans from smaller / lower power motors shoehorned into place in the turbo BMW engine bay. To solve these problems BMS designed their oil catch can kit from the ground up specifically for the turbo BMW application. It features 100% CNC machining with zero welding for a precision fit and long life. The can itself is guaranteed for the life of the vehicle. The hoses exceed the OEM PCV piping in diameter and that flow rate is maintained throughout the entire oil catch can ensuring no excessive crankcase pressure buildup. The BMS OCC retains the factory fully closed loop PCV operation preventing any PCV vapor from leaking to the atmosphere. The mounting locations are selected to minimize the line length, allow more efficient operation, and retain a stealth look. Install takes around 20 minutes, includes all required hardware, and is 100% reversible. Simply unscrew the base of the can or use the drain plug to safely dispose of captured oil with the rest of your used motor oil during oil changes. Made in USA. FEATURES AND BENEFITS Increases Air Intake Efficiency Promotes Engine Longevity Non-Clogging Air/Oil Separation Double Baffle Large 16mm+ inlet and outlet exceeds OEM PCV sizing Free Flow Solid No Restriction Design Retains factory fully closed loop PCV operation Large Intake/Outlet No Tapering Down Stealth Mounting on Cool Side of the Motor Anodized Black Aluminum N54 Model Mounts Out of Sight Under the Cowl Made in USA & Guaranteed for Life Non-Clogging, No Service Needed Air/Oil Separation Double Baffle High flow to eliminate crankcase pressure caused by more restrictive designs Precision CNC Machined from Solid Blocks of High Grade Aluminum DIMENSIONS Can dimensions with lid: 4.4" (111mm) Tall Can Diameter: 2.7" (68.5mm) Lid Length: Back to nozzle end: 4" (101mm) Nozzle Outer Diameter: .75" (19.2mm) Nozzle Inner Diameter: 0.669" (17mm) Can Capacity: 2.5 oz (74 ml)

Show More Show Less

BMW S58 3.0L ARP Head Stud Kit - CA625+

T#:22427036

Part#: ARP-HSK-S58-CA

Ships in 3 Business Days

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

BMW S58 3.0L ARP Head Stud Kit - CA625+ is the ultimate upgrade for the BMW S58 engine, specifically designed for high-performance models such as the F97 X3M, F98 X4M, G80 M3, G82 M4, G83 M4, and G87 M2. Manufactured by Turner Motorsport, this head stud kit ensures optimal engine reliability and performance.

Enhanced Strength: Featuring Custom Age 625+ material with a tensile strength of 260 ksi, this kit provides superior strength compared to factory bolts.
Prevents Head and Block Separation: Designed to handle increased boost levels and high-stress conditions, preventing potential head and block separation.
Precision Engineering: ARP’s advanced manufacturing process ensures that these head studs outperform standard factory bolts under extreme conditions.
Ideal for High-Performance Builds: Perfect for enthusiasts pushing the limits of their S58 engines, offering unparalleled durability and reliability.
Direct Fit: Specifically tailored for the turbocharged inline 6-cylinder BMW S58 engine, ensuring a seamless installation and optimal performance.

Show More Show Less

419 Piece Metric O-Ring Assortment Kit

T#:641935

Part#: WLMW5203

Ships in 1 Business Day

$ 19.99 USD

Add to Wish List

Qty

$ 19.99 USD

Add to Wish List

Many uses around the garage and home

BMW | Screw

T#:57231520

Part#: 07119901299

In Stock

$ 2.99 USD

Add to Wish List

Qty

$ 2.99 USD

Add to Wish List

M8x16

ARP Main Stud Kits - S58

T#:22427031

Part#: ARP-MSK-S58

Ships in 3 Business Days

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Elevate your BMW S58 engines with the ARP Main Stud Kit, replacing part numbers 11118604584. These studs prevent main cap walk, ensuring stability and protecting the engine from potential damage. They also safeguard the engine block threads, adding an extra layer of protection. Opting for main studs over factory bolts requires engine builders to mic the bores. Studs may require a line hone for proper fitment and alignment, ensuring round and concentric main bearing bores, preventing premature bearing wear, and ensuring optimal oil clearance.

Project Cars

SELECT YOUR BMW

Engine Hardware

Athena Cut Ring Head Gasket - 84.5mm - BMW M50 M52 (84mm Bore) ...

407 Piece O-Ring Assortment

Blue Thermostat Caps (pair)

Billet Oil Thermostat Lid

Burger Motorsports Turbo Double Baffle Oil Catch Can - F23 235i Conve...

BMW S58 3.0L ARP Head Stud Kit - CA625+

419 Piece Metric O-Ring Assortment Kit

BMW | Screw

ARP Main Stud Kits - S58

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results