Bearings

Rod bearings should be replaced as a preventative measure before 80,000 miles. This package is the most complete rod bearing overhaul kit available and includes not just the latest BMW rod bearings and connecting rod bolts, but also everything else that should be replaced with the oil pan and front subframe off the car.

Rod bearings continue to be a sore subject among M3, M5, and M6 owners. The rod bearings in the S85 V10 have been known to fail within 60,000 miles. There could be a number of reasons for premature failure with a lot of finger-pointing as to the real cause. Whatever the reason, rod bearings are wearing out sooner than expected and their replacement should be considered a required preventative maintenance item. We suggest a replacement interval of between 60,000-80,000 miles with frequent engine oil analysis done along the way*. Driving moderately and allowing the engine to warm up before hard use will also extend rod bearing life.

After doing so many rod bearing replacements in our own service shop we have put together this comprehensive overhaul package. Our package includes -

Genuine BMW rod bearings
- 11247841703, upper bearings - latest design from BMW (either original or WPC treated**)
- 11247841702, upper bearings - latest design from BMW (either original or WPC treated**)
- 11247834522, connecting rod bolts
- Red Line engine assembly lube

Oil Pan
- 11137836361, oil pan gasket
- 07119905485, oil pan screws (required by BMW)
- 07129905600, oil pan screws (required by BMW)
- 11137836568, oil pan screws
- 07119963129, seal washers
- 11417836233, auxiliary oil pump gaskets
- 11121304174, oil pickup tube o-ring

Replacing the rod bearings requires mechanical knowledge and skill, a clean workspace, and several specialist tools. Our preferred procedure is to leave the engine in the car but remove the front subframe. The engine must be supported from above with an engine brace. Removing the front subframe involves disconnecting the control arms and steering rack and steering column. The oil pan can then be removed and you can access the connecting rods and bearings. Replacing the rod bearings themselves is straightforward but patience and forethought will be extremely helpful. In addition to analyzing the severity of the rod bearing wear, the crankshaft must also be inspected closely for damage. Rod bearings that have been severely worn may have damaged the crankshaft (requiring replacement or machining).

* BMW released an updated rod bearing around 2011 that uses different materials than the original design. The old rod bearings were constructed with several layers or metal, including copper and lead. If an engine oil analysis revealed high levels of these specific metals then it was a sure sign that the rod bearings were nearing replacement. However, the new BMW bearings do not use copper or lead so an oil analysis will not alert you to heavy bearing wear. The new bearings are also a harder material which prolonged the life of the bearing but increased the liklihood of crankshaft damage if a bearing failed. Even though the bearing theoretically lasts longer it's even more important to preventativly replace them before they damage the crankshaft.

** These WPC-treated bearings are the best we have seen for the S85. WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are factory BMW bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

***BE Bearings is another top pick when considering which bearing kit to choose. Working with Clevite, an OE bearing supplier, their design allows for a bit more clearance than stock, allowing better oil circulation and reducing friction. The material is also made from the original bearing composition of lead-copper, not the updated tin-aluminum used in factory BMW bearings which was excessively hard, potentially damaging the crankshaft when high friction occurred. This softer metal composition can also be tested for via oil analysis, allowing you to see high bearing wear, something the tin-aluminum bearings don't give you the ability to do.

Internal VANOS Pressure Line
One of the VANOS oil lines runs along the inside of the timing chain cover and into the oil pan. It can only be replaced with the oil pan removed. If you have sluggish performance or VANOS fault codes this is one of the common causes and now is the perfect time to replace it. If it fails down the line the oil pan will have to be removed again.

Front Subframe Hardware
Our preferred procedure for accessing the engine block is by disconnecting the control arms and steering rack and then removing the front subframe altogether. This hardware is not required but may be a good idea, especially if your original subframe bolts are rusty. Hardware includes:
31106760222, front subframe mounting bolts
31106770256, front subframe mounting bolts
33326760668, front wishbone collar nut

Tie Rod Boots
32106765782, tie rod boot kit

Motor Mounts with Hardware
22116762607, left motor mount
22116762608, right motor mount
07129904088, motor mount bolts
07129904865, motor mount nuts

Engine Oil Change
Liqui Moly GT1 10w-60 engine oil
11427840594, OEM oil filter.

This package fits the following BMWs:
2006-2010 E60 BMW M5
2006-2011 E63 BMW M6

Protect your S65 engine from potential rod bearing failure by choosing the BE Bearings and Clevite collaboration. These upgraded rod bearings offer increased clearance and a lead-copper material composition, safeguarding against catastrophic engine failure caused by spun bearings. The innovative Clevite Tri-Metal design, featuring Tri-Armor™ coating, ensures improved lubrication, wear prevention, and tolerance to foreign particles in the oil. The softer bearings are gentle on your engine and enable accurate oil testing to monitor engine wear.

This kit includes:

• Upper and lower BE Bearings upgraded rod bearings
• Hardware
• Oil filter
• Castrol TWS Edge Professional
• Oil pan gasket
• RedLine assembly lube

Enhance your S65 engine's durability and performance with this comprehensive kit from Turner Motorsport.

The S62 engine has a known history of rod bearing failure. If your engine is higher mileage, don't let this catastrophic failure happen to you. Replace your rod bearings and prevent a spun bearing, a failure that has the potential to trash your crankshaft.

What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both. What are you waiting for? Use WPC-treated bearings on your next engine build or rod bearing service!

Kit Includes:

Turner Motorsport "Race Series" WPC-Treated Rod Bearing Shells (16) Genuine BMW Connecting Rod Bolts (16) OEM Hengst Oil Filter Kit Castrol Edge Euro Car Engine Oil (10w-60) - 7 Quarts Turner Oil Change Decal Elring Oil Pan Gasket Permatex Ultra Slick Engine Assembly Lube (4 oz.)

VAC Motorsports High-Performance Rod Bearing Kit for BMW S62 Engine

Experience unparalleled reliability and performance enhancement for your BMW S62 engine with VAC Motorsports' High-Performance Rod Bearing Kit. Designed to address the Achilles heel of S62 engines, these rod bearings are a favorite among BMW enthusiasts and engine builders worldwide. Say goodbye to thermal breakdowns and friction issues with this kit that includes ARP connecting rod bolts, VAC Motorsports' coated rod bearing set, and ARP assembly lubricant. Maximize efficiency and prevent costly engine failures with this essential upgrade.

• Enhanced reliability for forced induction and high-power N/A builds
• Friction-resistant bearings for optimal performance
• Immune to thermal breakdowns caused by lubrication issues

If your engine has higher mileage, don't neglect rod bearing replacement! These bearings are sandwiched between the connecting rod and crankshaft journal and are prone to failure due to overheating, lack of lubrication, or general wear. Replace your rod bearings and prevent a spun bearing.

Starting with ACL’s high-performance bearing shells, our Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Kit includes

Turner Motorsport WPC-Treated Race Series Rod Bearing Shells (16) Genuine BMW Connecting Rod Bolts (16) Hardware for Oil Pan & Oil Sump Oil filter Liqui-Moly Molygen 5W-40 (6L) Drain Plug Turner Motorsport Oil Reminder Sticker Oil pan gasket RedLine assembly lube (4 oz.)

Enhance Your BMW Engine with WPC-Treated OEM Connecting Rod Bearings

Upgrade your BMW engine performance by choosing WPC-treated OEM connecting rod bearings, surpassing the advantages of Original BMW bearings. WPC surface treatment is renowned for its ability to reduce friction and enhance component strength. Through ultra-fine particle blasting at high speeds, this treatment ensures smoother and stronger surfaces by utilizing thermal discharge. Combatting the critical enemies of heat and friction, WPC-treated bearings offer superior performance for your engine build or rod bearing service.

Key Benefits:

• WPC-treated OEM connecting rod bearings for enhanced engine performance
• Reduction in friction and addition of strength through surface treatment
• Ultra-fine particle blasting results in smoother and stronger surfaces
• Mitigates heat and friction, critical for high-performance engines

This kit includes everything needed to replace your rod bearings.

Kit includes

Upper and lower WPC-treated connecting rod bearings Hardware Oil filter Molygen New Generation Engine Oil (5w-40) - 7 Liters Oil pan gasket RedLine assembly lube

If you're the proud owner of an S14-equipped, chances are you're passionate about enhancing your vehicle's performance and longevity. One crucial upgrade that can significantly improve your driving experience is Turner Motorsport's WPC Rod Bearing Replacement Kit, designed for enhanced durability and wear protection. Prevent costly mechanical failures and increase engine life with our WPC-Treated Performance Rod Bearing Service Kit!

Enhanced Durability: The WPC Performance Rod Bearing Replacement Kit is designed with superior materials and manufacturing processes. WPC treatment reinforces the surface of the bearings, making them highly resistant to wear, which is essential for aging engines like the S14. This durability ensures your engine will stand the test of time, even under strenuous driving conditions. Improved Performance: By reducing friction and wear, WPC-treated rod bearings allow for smoother and more efficient engine operation. This translates into increased power and responsiveness, providing you with a more exhilarating driving experience. Whether you're tearing up the track or enjoying a spirited weekend drive, you'll notice a difference in your vehicle's performance. Preventative Maintenance: Proactively replacing your rod bearings and bolts with the WPC Performance Kit can prevent potential engine failures. As engines age and accumulate miles, wear and tear become inevitable. These components help you address this issue head-on, preventing costly engine damage and repairs down the road. This is especially crucial for BMW E30 M3 owners who value their investment. Long-Term Cost Savings: While the initial investment in a WPC Performance Rod Bearing Replacement Kit may seem substantial, it's a small price to pay for the long-term benefits. Preventing engine failure and costly repairs can save you thousands of dollars over the life of your vehicle, not to mention the peace of mind that comes with knowing your BMW is built for reliability. Included in the kit:

8 - Turner Motorsport WPC-Treated "Race Series" Rod Bearing Shells 1 - Oil Pan Gasket 1 - Oil Filter Kit 1 - Oil Drain Plug 8 - Genuine BMW Connecting Rod Bolts 1 - Liqui Moly 10w-40 Engine Oil - 5 Liters 1 - Liqui Moly 10w-40 Engine Oil - 1 Liters 1 - Assembly Lube - 4 oz

Upgrade your engine build with Turner's WPC-treated Race Series Bearings, engineered for serious performance enthusiasts. Starting with ACL’s high-performance bearing shells, these Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Key Features:

Duraglide Tri-Metal Construction: ACL's Race Series bearings feature a high-strength overlay for enhanced performance. Optimized Oiling: Designed to promote better oil flow during high-RPM conditions. Precise Fitment: Manufactured with OEM-level precision using micron tolerance machining. WPC-Treated for Strength: Surface treatment adds strength and reduces friction for improved engine performance. No Flash Plating: Allows for better heat transfer and bearing retention. Thermal Discharge Process: Smoother, stronger components through WPC’s unique thermal discharge technology. Enhanced Heat and Friction Resistance: Built to combat the biggest enemies of high-performance engines. Don’t settle for standard bearings—choose Turner Motorsport WPC-treated Race Series Bearings for the ultimate engine performance upgrade. Perfect for your next engine rebuild or rod bearing service!