ECS BMW Intake Parts

The factory plastic gears in BMW S65 and S85 throttle body actuators are notorious for premature wear due to mechanical stress, engine vibration, and heat cycling. Over time, this wear leads to excessive play, throttle response issues, and eventual failure. This can cause DME fault codes, limp mode, and DSC malfunctions. While replacing both throttle actuators is costly, even new OEM units will eventually suffer the same fate.

Thankfully, ECS has developed the ultimate solution for E9X M3, E60 M5, and E63/64 M6 owners! These Upgraded Throttle Body Actuator Gears are constructed of Teflon-reinforced nylon, significantly reducing friction and gear tooth wear for long-term reliability. Each gear comes pre-installed on a 4140 steel shaft, strengthening the assembly and ensuring a hassle-free installation. With this cost-effective and durable fix, you can eliminate throttle actuator failures for good!

Features & Benefits:

Upgraded Teflon-reinforced nylon gears – Superior to factory plastic-on-plastic gears, reducing wear and extending lifespan. Pre-installed 4140 steel shafts – Increases durability and simplifies installation. Prevents common actuator failures – Resolves worn gear issues that cause CELs, limp mode, and DSC/DME errors. Cost-effective alternative to full actuator replacement – Saves hundreds in parts and labor. Factory-like fitment – Engineered for precise compatibility and long-term reliability. Built to withstand heat and mechanical stress – Ensures consistent throttle performance and extended service life.

Upgraded replacement for your crankcase vent hose P#11127584128 featuring upgraded silicone, stainless steel clamps, and new OE connectors and seals.

Enhance your BMW N55 engine with our Silicone Crank Case Vent Hose, a premium replacement for the fragile, failure-prone factory hose. Over time, the stock plastic hose deteriorates due to constant exposure to heat and oil, leading to cracks and leaks. Our solution? A high-quality silicone hose engineered for superior durability and long-term reliability.

To further enhance performance, we’ve lined the hose with fluorosilicone, providing exceptional resistance to oil and chemical degradation. Designed in-house using advanced CAD modeling and 3D scanning, this hose offers a precise OEM fit while eliminating the common weaknesses of plastic construction.

Each kit includes stainless steel hose clamps for a secure, hassle-free installation. Whether you’re replacing a worn-out CCV hose or upgrading for added peace of mind, this premium solution ensures your BMW N55 runs smoothly and efficiently for years to come.

Features:

Arrives preassembled with new OE fittings and seals
Direct OEM Fit – Retains factory hose dimensions while eliminating reliability issues.
High-Performance Silicone – Resists heat-related wear for long-lasting durability.
4-Ply Fluorosilicone Lining – Superior protection against oil and chemical exposure.
Stainless Steel Clamps Included – Secure installation and extended service life.
Give your BMW N55 the reliability it deserves—upgrade to the ECS Tuning Silicone CCV Hose today!

The S55's factory intake system is a major bottleneck, muting its aggressive twin-turbocharged soundtrack and restricting performance. Oversized airboxes, restrictive paper filters, and charcoal pre-filters choke airflow, limiting power and induction noise. The result? An underwhelming driving experience that doesn’t do the twin-turbo-six justice.

ECS aims to solve this issue with their Luft-Technik Performance Intake System—engineered to optimize airflow, amplify induction sound, and completely transform your engine bay. By replacing the factory restrictions with a high-flow design, this system unleashes the S55’s true potential, delivering sharper throttle response, enhanced turbo efficiency, and an intoxicating intake note.

At its core, the Luft-Technik intake is comprised of dual aluminum inlet tubes, designed for both strength and function. Constructed from 6061 aluminum and finished in a wrinkle black powder coat, these tubes are built to withstand high engine bay temperatures and extreme conditions. Using advanced CAD modeling, ECS engineers optimized the tubing shape to ensure perfect MAF sensor scaling, maintaining factory AFR (air-to-fuel ratio) for peak reliability and efficiency. The unique ovular profile maximizes clearance around critical engine components while allowing for the largest possible inlet diameter. The crossover tube features standoffs for secure heat exchanger hose mounting and a CNC-machined 6061-T6 billet aluminum MAF flange and vacuum port, ensuring seamless integration with factory connections.

To prevent heat soaking and maintain consistent performance, our intake system incorporates precision-cut aluminum heat shields. Finished in a durable wrinkle black powder coat, the heat shields feature a rubber edge trim that seals against the hood, preventing engine bay heat from infiltrating the air intake tract. This results in lower intake air temperatures (IATs), improved air density, and overall improved performance even under demanding conditions.

Key Features:

Aluminum Inlet Tubes 6061 aluminum construction for durability and heat resistance Wrinkle black powder coat for a sleek, OEM+ finish Optimized ovular shape for maximum clearance and airflow Gradual transitions eliminate sharp bends for smoother intake flow MAF scaling matched to factory specs for precise AFR control CNC-machined 6061-T6 MAF flange and vacuum port for OEM fitment Aluminum Heat Shields One-piece aluminum construction for durability and heat isolation Wrinkle black powder coat for a stealthy appearance and heat resistance Rubber edge molding creates a perfect seal against the hood, blocking hot air Mounts to factory locations for hassle-free installation High-Flow Dual-Cone Air Filters 8-ply cotton gauze construction for superior filtration and flow Bellmouth 3" flange inlet minimizes turbulence and maximizes efficiency Enhanced induction noise for an aggressive turbocharged soundtrack Installation & Support:

Click HERE for a guided installation tutorial!

The ECS Tuning  Kohlefaser Luft-Technik (Carbon fiber Air Technology) line is a premium intake system designed to fit like OEM with added performance gains and appearance. This intake allows you to maintain a factory like seal enclosure and the ability to work with the JCW and GP2 strut tower brace.

The ECS Tuning Kohlefaser Luft-Technik Intake System features:

• Gains of +3 WHP / +4 FT-LBS TQ on 100% Stock Vehicle Cooper S

• Gains of +11 WHP / +10 FT-LBS TQ on 100% Stock Vehicle JCW

• Broader and smoother torque curve for an enhanced driving experience

• Sealed Carbon Fiber Upper,  Lower Intake Box & Upper Intake Tube

• 4.5" - 5.0" ECS Tuning Performance Cone, Cotton Gauze, Reusable Air Filter

• MINI Factory location clips

• 4-Ply Silicone Couplers,  Stainless Steel Hose Clamps, and Hardware

*Not CARB Approved.

The S58 engine is BMW’s latest twin-turbocharged powerhouse—a genuine S-series motor that checks all the boxes: massive top-end power, instant torque, and a raw induction tone that deserves to be heard. Unfortunately, this masterpiece is muted by a restrictive intake system designed to meet NVH (noise, vibration, and harshness) regulations. The result? A silent engine note and airflow constrictions that leave performance on the table.

During testing, ECS engineers identified multiple drawbacks in the stock setup. The factory intake features a catacomb-like airbox design with excessive internal baffling and sound-deadening resonators. Hidden inside are eight restrictive panel filters that severely limit available airflow. While the insulation helps with cabin quietness, it also silences the engine’s mechanical soundtrack and holds back the S58’s full potential.

The ECS Luft-Technik Performance Intake System is purpose-built to address these shortcomings and deliver measurable improvements in both sound and performance! With the Luft-Technik system installed, you’ll hear the turbochargers breathe, spool, and surge with every touch of the throttle. Whether you're chasing lap times or just want to bring your S58 to life, this intake system delivers real performance and the soundtrack to match.

Performance Features & Benefits:

Replaces the entire restrictive OEM assembly with a simplified, high-flow design

Utilizes dual high-flow cone filters connected directly to the turbocharger inlets

Improves airflow by an average of 30 CFM over the factory setup

Reduces intake complexity while unlocking aggressive, turbocharged induction sound

Results in sharper throttle response and noticeable top-end power gains

Installation & Support:

Looking for installation instructions? Look no further! ECS has provided a detailed installation PDF that includes directions on removing your factory components! See the tab labeled "Installation" above for more information.

Maximize cooling efficiency and take your BMW’s performance to the next level with the ECS High Performance Cooling System Bundle—a complete, track-proven upgrade engineered to handle the extreme thermal demands of the G2X B58 platform. Developed by the enthusiasts at ECS Tuning, this system includes both the High Performance Aluminum Radiator and High Performance Aluminum Heat Exchanger, designed to deliver consistent, reliable temperature control in even the most demanding driving conditions.

The factory BMW cooling components just aren’t built for high-performance or track use. Both the OE radiator and heat exchanger feature weak plastic end tanks and undersized single-row cores—common failure points when exposed to elevated heat and pressure. ECS set out to solve these shortcomings with an all-aluminum, dual-row system designed for enthusiasts who demand more from their BMW. ECS engineers started by replacing the fragile plastic end tanks with TIG-welded 6061-T6 aluminum for unmatched durability. Each tank is precision-crafted with CNC-machined billet aluminum hose connections, flanges, and brackets, ensuring direct OE-style fitment with the factory hoses, fan shroud, and accessories—no cutting or modifications required.

Both the radiator and heat exchanger feature high-capacity, dual-row 42mm cores, a massive improvement over the factory’s 34mm and 25mm single-row designs. The result? Faster heat dissipation, lower intake air temperatures, and more consistent performance, whether you’re cruising or carving apexes.

Radiator: Replaces OEM part numbers 17118666740 and 17115A30677

Heat Exchanger: Replaces OEM part numbers 17118666811 and 17115A54040

Features:

6061-T6 aluminum construction eliminates weak plastic end tanks Dual-row core design for increased cooling capacity and efficiency Radiator: 42mm dual-row core (45% thicker than OE 34mm core) Heat Exchanger: 42mm dual-row core (72% thicker than OE 25mm core) TIG-welded end tanks for superior strength and reliability Polished aluminum finish for a premium, high-performance look CNC-machined connectors and brackets for perfect OE fitment Fully compatible with factory hoses, fan shroud, condenser, and intercooler Direct bolt-in installation—no modifications required

Free-flowing intake featuring a roaring induction noise and increased performance to replace your restrictive factory intake.

Upgrade your E46 driving experience by adding induction noise and increased air flow. Let your engine breath and listen to the sweet sweet intake sounds!

With the factory intake you are limited to a finite amount of air, this leaves your engine under-served and limits induction noise. When it comes to the recipe for upgrading your E46 there are a few ingredients that you must have, power and sound. While you can add an exhaust for a bit more power and sound, the biggest difference you can make is adding power and sound under your hood with a high-flow intake. The factory intake box is also referred to as a silencer specifically designed to lower the induction noise for a refined driving experience, this helped exponentially when selling the cars out of the show room circa early 2000's. We as enthusiasts are no longer interested in subdued intake noise and limited air-flow, we want pure induction noise, we want to hear the air being sucked into the engine as we push down on the accelerator.

Key benefits:

Flows on average 71 CFM more than the stock intake system, a ~27% increase in intake efficiency
Increased induction noise
Maintains factory air induction track
Maintains Stock MAF location, allowing user to switch back to the stock airbox and retain the ECS Silicone boot if desired
Design:

Durable, lightweight 6061 and 5052 aluminum intake tube and bracket design, finished in wrinkle black powder coat
Mounts to locations on chassis utilizing Stainless Steel M6 hardware
MAF mounts to intake using aluminum brackets sealed to intake system with OEM fitment
Maximizes available engine bay space to fit oiled ECS cotton gauze 7” filter
Silicone intake boot with improved flow characteristics replaces failure-prone facotry accordion intake boot with provisions for F-connector fitting and Idle Air Control (IAC) valve inlet