Select Vehicle
BMW
Mini
Purpose
Category
- Control Arm Replacements & Upgrades
Create an account to be able to build Wish Lists.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
Stock rear lower control arms offer very little adjustment for alignment, especially in lowered vehicles, due to their use of an eccentric bolt. These aftermarket performance control arms from ECS Tuning are designed for maximum adjustability, allowing you to maximize handling and minimize tire wear.
To ensure maximum reliability, ECS Tuning's control arms are constructed from strong, lightweight 6061-T6 aluminum and feature a 303 stainless steel center turnbuckle that offers over 8 degrees of fast and precise camber adjustment. The inner bushing is a stock style serviceable OEM bushing for long life and inexpensive maintenance.
Features:
Durable construction suitable for the daily driver and track car alike
8+ degrees adjustment range for dialing in any suspension and wheel/tire setup
Center located adjuster for maximum clearance during adjustment
OEM-style bushing for long life and inexpensive service
Black anodized 6061-T6 aluminum with 303 stainless steel turnbuckle
Includes new hardware
*With the exception of the stance community, most enthusiasts will need no more than a few degrees of adjustment range. Total adjustment often is dependent on wheel/tire clearances.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
The rear lower control arms on E82/E9X models are the weakest link in the rear suspension. The arm is made from folded sheetmetal and it bends and deforms easily. Not only will it deform from potholes and curbs, tow truck drivers love to hook onto them without realizing how weak they are. We have seen other race teams complete the box section to make them stronger. A bent arm will throw off the geometry in the suspension, potentially affecting handling and tire wear. These aluminum arms are both lighter and stronger than the factory sheetmetal arms and is the best solution for chronic bending of the stock arm. These are a direct replacement to your stock arms with no changes needed to your alignment. New high-grade hardware is included.
Note: the stock arm is designed from the factory to be intentionally weak. These arms will bend so that something else in the suspension does not break. Our race cars used the stock sheetmetal arm but we replaced them often. We found that it was better to finish a race with a bent arm than not finish due to a catastrophic failure. The ECS arms are still designed to be the weakest link but are far stronger than the factory arm and will not bend as easily.
This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi M3 - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
The E36/E46 rear trailing arm bushings (RTABs) wear out faster than any other bushing on the car. Worn RTAB will cause excessive toe alignment change and give a 'loose' or 'floaty' feeling in the rear handling. One of the reasons for this is that they over-extend during motion, stretching and twisting the rubber in all directions. These shims sit on either side of the bushing and limit the amount of extension from the bushing. Not only will you get more life from your RTAB but these will help stiffen the bushing during cornering. But during normal driving you will still have all of the comfort of the stock rubber bushings. These part about these bushings is how easy they are to install - simply slide them in place during your bushing install. They can be added to pre-installed bushings too by dropping the trailing arm and removing the cage around the bushing.
Works with stock rubber bushings only (not urethane or Delrin).
Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.
Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3
Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36
Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty
Swapping in E46 control arms into your E30 or E36 will significantly increase negative camber by widening the track width and will also give you more clearance for more steering angle. Condor's conversion bushings are machined from UHMW due to its high rigidity and low coefficient of friction allowing for minimal suspension bushing deflection (geometry change). They've designed them offset to re-center the wheel and give your e30/e36 the correct caster. They will include a stainless-steel insert that tightly presses over the hex pattern on the E46 control arms. You do not need to grind down your control arms or make any other modifications to your chassis. Please note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36.
Fitment:
Fits the following Meyle and Lemforder arms with 21-22MM Hex.
LEMFORDER ZHP - 31122282121 & 31122282122
LEMFORDER - 31126777851 & 31126777852
MEYLE HD - 31126777851 & 31126777852
*Please note that Meyle makes a standard e46 control arm and a Heavy Duty control arm. SOME HD arms have a hex that is larger in size. These HD control arms may need to be shaved 1-2 mm for proper fitment.
When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.
This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear.
Features:
Updated design! Now shipping!
When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.
This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear.
Features:
100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).
Stainless hardware and spacers are perfect for the tough Northeast climate!
New! Easy adjustment with 22mm open ended wrench and 5mm allen key! It only requires 15 ft. lbs. on the clamp to secure the clamp!
New! Included lock-out kit, replaces factory eccentric hardware.
Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners
Extremely easy installation and adjustment (your alignment shop will LOVE you!)
Rogue Engineering E82/E9X Adjustable Rear Camber Link Set V2.0 is the ultimate upgrade for BMW enthusiasts seeking enhanced handling, improved tire wear, and precise suspension tuning. This high-performance solution is engineered to fit BMW E82 1-Series and E9X 3-Series models, offering superior adjustability and durability over OEM components. Ideal for street and track use, this camber link set is crafted from premium materials to ensure strength and long-lasting performance.
Key Features:
These replace the wishbone and guide arm links in the factory suspension which have rubber bushings and limited adjustment. Enhanced suspension adjustability for optimized alignment Improves handling and reduces uneven tire wear Compatible with BMW E82 1-Series and E9X 3-Series models Constructed from high-strength materials for durability and reliability Perfect for both street performance and track applications Turner Motorsport proudly offers the Rogue Engineering E82/E9X Adjustable Rear Camber Link Set V2.0, providing BMW drivers with unmatched performance and precision.