BMW Internal Engine Parts

BE Bearings - S65 Connecting Rod Bolt Set - BMW E9X M3

T#:403653

Part#: BE-CRB50-S65

In Stock

$ 294.99 USD

Add to Wish List

Qty

$ 294.99 USD

Add to Wish List

Designed by BE Bearings, manufactured by ARP. These custom made rod bolts are designed to be used on BMW factory connecting rods. BE Bearings worked with ARP to come up with custom rod bolt torque specifications to ensure minimal rod big end bore distortion. Their bolts have been measured and verified to guarantee minimal bore distortion, and stay within the ARP torque specification.

Show More Show Less

BMW S65 BE Bearings Connecting Rod Bearing Upgrade Set

NOW SOLD AS SP1527F-STD-S65 (V2)

T#:403655

Part#: SP1527HKSTDS65

In Stock

$ 589.00 USD

Add to Wish List

Qty

$ 589.00 USD

Add to Wish List

BMW S65 BE Bearings Connecting Rod Bearing Upgrade Set is designed to address the known flaws in the factory BMW rod bearings, particularly for the S65B40 engine. Manufactured by Clevite to BE Bearing specifications, this set provides a crucial upgrade with its enhanced materials and design, ensuring improved performance and durability.

The original BMW bearings have minimal clearance, which leads to premature wear and potential engine failure. This upgrade replaces the tin-aluminum factory bearings with a superior silver-oxide-coated tri-metal "F" series design. The new bearings can handle 30% more load, offer better performance in low oil conditions, and are more forgiving of foreign particles in the oil. Designed specifically for BMW S65 engines, these bearings provide optimal performance for high-horsepower applications.

Designed specifically for BMW S65B40 engines
Silver-oxide coating withstands 30% more load capacity
Improved performance under low-oil and boundary conditions
Stronger backing material for enhanced durability
Corrects factory BMW rod bearing clearance issue
Ideal for high-horsepower applications and factory 10W60 weight oils
Complete set for 8 cylinders, ready for installation

Fits the following BMWs:

2008-2013 E9X BMW M3 (S65)

Show More Show Less

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

BE Bearings Connecting Rod Bearing Upgrade Set - BMW S85

Now ordered under BE Bearings "SP1527F-STD-S85"

T#:403658

Part#: SP1527HKSTDS85

In Stock

$ 734.00 USD

Add to Wish List

Qty

$ 734.00 USD

Add to Wish List

Designed and manufactured by Clevite to BE Bearing specifications.

These bearings replace the factory BMW rod bearings. The original BMW bearings have too little clearance, which leads to premature bearing wear and can cause early engine failure. Furthermore, the factory BMW bearings are made from tin-aluminum which are 5-times harder than a softer lead-copper bearing design. A softer bearing is better for your engine and more tolerant of foreign particles suspended in your oil.

These BE Bearings feature a state-of-the-art Clevite Tri-Metal design with the Clevite Tri-Armor(tm) coating.

Lead-copper design for greater durability and easy tracking with oil analysis like Blackstone (recommended).
Designed with extra clearance to "fix" the BMW rod bearing design flaw.
Designed for use with factory 10W60 weight oils.
Tri-Armor coated for low conditions during cold start
Ideal for start-stop vehicles
Applicable for BMW engines S85B50
Standard Clearance
Sold as complete set (10-cylinders)

Fits the following BMWs:
2005-2010 E60 BMW M5
2005-2010 E63/64 BMW M6

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

BE Bearings Connecting Rod Bolt Upgrade Set - BMW S85B50

T#:403657

Part#: BE-CRB50-S85

In Stock

$ 369.00 USD

Add to Wish List

Qty

$ 369.00 USD

Add to Wish List

Designed by BE Bearings, manufactured by ARP. These custom made rod bolts are designed to be used on BMW factory connecting rods. BE Bearings worked with ARP to come up with custom rod bolt torque specifications to ensure minimal rod big end bore distortion. Their bolts have been measured and verified to guarantee minimal bore distortion, and stay within the ARP torque specification.

Technical Details:

Composition: ARP2000®
Yield strength: 200,000 PSI
Tensile strength: 220,000 PSI
Torque specification: 50 Ft/Lbs, or 0.0065-0.0070 inch stretch

Fits the following BMWs:
2005-2010 E60 BMW M5
2005-2010 E63/64 BMW M6

Show More Show Less

Rein Piston Rings - Set - Single Piston - E36, Z3

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:591603

Part#: 11251405783

Back Ordered

$ 43.99 USD

Add to Wish List

Qty

$ 43.99 USD

Add to Wish List

Replace your worn out piston rings with OE replacements - 86.415mm

Glyco Connecting Rod Bearing Set

T#:375825

Part#: 11241284849

Ships in 1 Business Day

$ 92.02

This product was last offered at the strikethrough price on
07-15-2026

$ 84.36 USD

Add to Wish List

Qty

$ 84.36 USD

Add to Wish List

Standard bore - 45mm

Rod Bearing - E30 M3, E28 M5, E24 M6, E34 M5 (sold individually) ...

T#:183

Part#: 11241310515

In Stock

$ 30.59

This product was last offered at the strikethrough price on
05-03-2026

$ 27.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 30.59

This product was last offered at the strikethrough price on
05-03-2026

$ 27.99 USD

Limited Qty Sale

Add to Wish List

E30 M3, E28 M5, E24 M6, E34 M5 Rod Bearing. Sold individually. Standard sizing.

This item fits the following BMWs
1988-1991 BMW E30 M3 - 8 required.
1988 BMW E28 M5 - 12 required.
1989-1993 BMW E34 M5 3.6 liter - 12 required.
1987-1989 BMW E24 M6 - 12 required.

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 6 Business Days

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Rein Piston Rings - Set - Single Piston

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:592808

Part#: 11251247917

Ships in 4 Business Days

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Replace your worn out piston rings with OE replacements - 85.065mm

Glyco "Yellow" Crankshaft Bearing Shell - Set - E28, E30, E34, E36, E...

T#:375823

Part#: 11211706847

In Stock

$ 136.06

This product was last offered at the strikethrough price on
07-15-2026

$ 125.04 USD

Add to Wish List

Qty

$ 125.04 USD

Add to Wish List

Standard bore

Rein Piston Ring Set

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:379819

Part#: 11251437077

Ships in 4 Business Days

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

Standard bore replacement piston rings

Rein Piston Ring - Priced Per Piston - E28, E30, E34, E36

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:379806

Part#: 11251713192

Ships in 3 Business Days

$ 30.99 USD

Add to Wish List

Qty

$ 30.99 USD

Add to Wish List

For use on stock pistons, will need 6 sets to replace all piston rings in the engine

Rein Piston Ring Set - Priced Per Piston

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:592811

Part#: 11251713178

Ships in 4 Business Days

$ 28.99 USD

Add to Wish List

Qty

$ 28.99 USD

Add to Wish List

Replace your worn rings - 84.000mm

BE Bearings Connecting Rod Bearing Upgrade Set - SP1534F - BMW S54 ...

T#:403644

Part#: SP1534HKSTDS54

Ships on Sep 14, 2026

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

NOTE: These bearings are now sold as SP1534F which features a new and improved silver oxide coating that is stronger and more durable! Designed and manufactured by Clevite to BE Bearing specifications. These bearings replace the factory BMW rod bearings. The original BMW bearings have too little clearance, which leads to premature bearing wear and can cause early engine failure. Furthermore, the factory BMW bearings are made from tin-aluminum which are 5-times harder than a softer lead-copper bearing design. A softer bearing is better for your engine and more tolerant of foreign particles suspended in your oil. These BE Bearings feature a state-of-the-art Clevite Tri-Metal design with the Clevite Tri-Armor(tm) coating. Lead-copper design for greater durability and easy tracking with oil analysis like Blackstone (recommended). Designed with extra clearance to "fix" the BMW rod bearing design flaw. Designed for use with factory 10W60 weight oils. Tri-Armor coated for low conditions during cold start Ideal for start-stop vehicles Applicable for BMW engines S54 Standard size Sold as complete set (6-cylinders) Fits the following BMWs: 2002-2006 E46 BMW M3 S54 2002-2003 Z3 BMW M Coupe, M Roadster S54 2006-2008 Z4 BMW M Coupe, M Roadster S54

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Main Bearing Set - Standard Size - E30 M3 2.3 liter

T#:3166

Part#: 11210666110

Ships in 4 Business Days

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

This E30 M3 Main bearing set is in standard size for the 2.3 liter S14 engine. This main bearing kit includes the thrust bearings.

This item fits the following BMWs:
1988-1991 E30 BMW M3

Show More Show Less

Glyco Main Bearing Set (Standard) - E21, E28, E30

Features All Single-Tang Main Bearings for Earlier M20 Engines

T#:1196183

Part#: 11211722342

In Stock

$ 259.99

This product was last offered at the strikethrough price on
05-03-2026

$ 231.99 USD

Add to Wish List

Qty

$ 231.99 USD

Add to Wish List

Glyco "Yellow" Crankshaft Bearing Shell - Set - E30, E36, E39, E46, E...

T#:375824

Part#: 11211706850

In Stock at Vendor

$ 126.61

This product was last offered at the strikethrough price on
07-15-2026

$ 118.92 USD

Add to Wish List

Qty

$ 118.92 USD

Add to Wish List

59.75MM(+0.25) bore

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Rein Piston Rings - Set - Single Piston - E30, E36

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:591604

Part#: 11251727461

Ships in 4 Business Days

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

Replace your worn out piston rings with OE replacements - 84.000mm

Spline Lock Crank Hub Solution

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - N54

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Rod Bearing Set (+0.25)

T#:23748157

Part#: 112412848516CYL-

Ships in 1 Business Day

$ 331.13

This product was last offered at the strikethrough price on
07-15-2026

$ 305.57 USD

Add to Wish List

Qty

$ 305.57 USD

Add to Wish List

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

T#:19395579

Part#: VTTCRANKHUBPKG

Ships in 10 Business Days

$ 934.99 USD

Add to Wish List

Qty

$ 934.99 USD

Add to Wish List

VTT is proud to offer the only complete N54 complete crank hub solution that does NOT require the crank to be drilled for pins. Our hub uses our proprietary “Spline Lock” technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). We spent many months testing, and retesting this design, utilizing well over 10 different samples to come to our final production version. During testing, our final hub managed to break our testing rig before slipping. These have been bench tested, and real-world tested on the VTT N54 race car spinning 8K RPM and making well over 900WHP. This technology means our hub installs the same as a stock hub, no drilling of the crank, which means MUCH less labor is involved and is reversible is ever wanting to be uninstalled leaving no holes in the crank. The “Spline Lock” is ONLY available with the VTT Crank bolt capture for the ULTIMATE Crank Hub solution for your BMW. These parts are designed to be used together, and the spline lock should not run without the CBC VTT “Spline Lock” Crank hubs are CNC manufactured from 440C tool Steel with a Rockwell rating of HRC60 for the ultimate in durability, and toughness. Hub Plus OEM bolt OEM Oil pump sprocket OEM oil sprocket retainer VTT Crank bolt capture

Show More Show Less

Glyco "Green" Crankshaft Bearing Shell - Set - E39, E46, E53, E83, Z3...

T#:374671

Part#: 11211706848

Ships in 1-2 days

$ 194.32 USD

Add to Wish List

Qty

$ 194.32 USD

Add to Wish List

Standard bore

N54 Spline Lock Crank Hub Solution With Complete Package

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 6 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Rein Exhaust Valve - E34, E36, E39, E46, Z3

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:379738

Part#: 11341739823

Ships on Sep 1, 2026

$ 20.99 USD

Add to Wish List

Qty

$ 20.99 USD

Add to Wish List

Replacement exhaust valve

OEM Rein Camshaft / Crankshaft Sensor O-Ring - Multiple BMWs ...

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:12463

Part#: 12141748398

In Stock

$ 4.99

This product was last offered at the strikethrough price on
06-29-2026

$ 2.75 USD

Add to Wish List

Qty

$ 2.75 USD

Add to Wish List

This is the o-ring used for most BMW camshaft sensors and crankshaft sensors. Although most sensors that we sell come with this o-ring at no charge, they may be the source of oil or fluid leaks.

Aluminum Cylinder Head Bolt Set

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:594302

Part#: 11120392547

In Stock

$ 12.99

This product was last offered at the strikethrough price on
08-13-2026

$ 7.89 USD

Add to Wish List

Qty

$ 7.89 USD

Add to Wish List

If you remove your cylinder head replacement head bolts are a must. These bolts are designed to be torqued down and not reused.

Rein Exhaust Valve - Sold Each - E28, E30, E34

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:584424

Part#: 11341708896

In Stock

Sale - Save 9% $ 18.35

This product was last offered at the strikethrough price on
05-14-2026

$ 16.65 USD

Add to Wish List

Qty

Sale - Save 9%

$ 18.35

This product was last offered at the strikethrough price on
05-14-2026

$ 16.65 USD

Add to Wish List

Replace your worn valves

Rod Bearing Set - Standard (48.00 Mm)

T#:55821723

Part#: 11241715701

Ships in 2 Business Days

$ 151.99 USD

Add to Wish List

Qty

$ 151.99 USD

Add to Wish List

Rein Alusil Piston Ring Repair Kit - E38, E39, E53

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:591608

Part#: 11259071606

Ships in 4 Business Days

$ 37.99 USD

Add to Wish List

Qty

$ 37.99 USD

Add to Wish List

Set of rings for one piston

Piston Ring - Priced Per Piston | BMW M54 3.0L Engine

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:591606

Part#: 11257506252

Ships in 4 Business Days

$ 48.99 USD

Add to Wish List

Qty

$ 48.99 USD

Add to Wish List

Piston Ring - Priced Per Piston | BMW M54 3.0L Engine is a vital component in maintaining proper compression and oil control in BMW M54 3.0L engines. Over time, piston rings experience wear from continuous movement within the cylinder bore, leading to decreased engine efficiency. Worn or damaged rings can result in excessive oil consumption, reduced performance, and visible black or blue smoke from the exhaust. Ideal for engine rebuilds, this high-quality replacement ensures optimal sealing and longevity.

Restores proper compression and oil control for improved engine performance
Reduces oil consumption and minimizes exhaust smoke
Direct-fit replacement for BMW M54 3.0L engine pistons
Manufactured from high-strength materials for durability and longevity
Essential for engine rebuilds and maintaining peak efficiency
Designed to withstand high temperatures and pressures for reliable operation

Show More Show Less

Glyco Connecting Rod Bushing - E12, E21, E23, E24, E28, E3, E30, E32,...

T#:187165

Part#: 11240618100

In Stock at Vendor

$ 12.99 USD

Add to Wish List

Qty

$ 12.99 USD

Add to Wish List

OEM BMW Connecting Rod Bush

OEM Rein Rocker Arm Shaft Plug - E28 E30 E34

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:583592

Part#: 11331264519

In Stock at Vendor

$ 6.11 USD

Add to Wish List

Qty

$ 6.11 USD

Add to Wish List

This is an OEM Rein replacement rocker arm shaft plug, also referred to by BMW as a Blind Plug. This plug connects to the end of the rocker arm shafts. 4 required per vehicle. Replace your old plugs to keep everything properly sealed.

Show More Show Less