Oil Cap

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

Replacement engine oil filler cap with seal (Original BMW brand). Oil caps can go bad.... If the cap is not sealing to the valve cover it will result in a vacuum leak (poor idle, rough running, etc). It also helps regulate pressure in the cylinder head. While there is no life expectency, there's no downside to replacing it every few years. This is a Genuine BMW part.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This item fits the following BMWs: 
1967-1976 2002 BMW 2002 2002tii 
1977-1983 E21 BMW 320i 323i 
1984-1985 E30 BMW 318i 
1984-1991 E30 BMW 325e 325es 325i 325is 325ic 325ix M3 
1982-1988 E28 BMW 528e 533i 535i 535is M5 
1989-1990 E34 BMW 525i 
1989-1993 E34 BMW 535i M5 
1977-1989 E24 BMW 633csi 635csi M6 
1977-1987 E23 BMW 733i 735i 
1988-1994 E32 BMW 735i 735il 

Designed to fix a known weak point for the MINI B3X and B4X engines, the ECS billet aluminium oil filter housing cap is a direct replacement for the factory plastic cap. The OEM plastic part is infamous for cracks, stripped threads, and rounded hex heads—often failing during routine oil changes and turning basic maintenance into a frustrating, time-consuming repair.

The engineers at ECS have designed a precision-machined billet aluminium upgrade that eliminates those issues, delivering strength, durability, and consistent fitment. An integrated drain plug allows you to drain the filter housing cleanly before removal, reducing spills and mess for a faster, cleaner oil service.

Replaces OEM MINI part number 11428575907.

FEATURES

Fixes common OEM plastic failures, including cracking, stripped threads, and rounded hex heads Precision-machined billet aluminum construction for superior strength and longevity Black anodized coating to prevent oxidation Integrated drain plug allows clean, mess-free oil changes Improves serviceability, reliability, and underhood appearance