Oil Filters

K&P Engineering High Performance Stainless Steel Micronic Oil Filter ...

Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:31158731

Part#: S34

In Stock

$ 109.00 USD

Add to Wish List

Qty

$ 109.00 USD

Add to Wish List

K&P Engineering High Performance Stainless Steel Micronic Oil Filter w/ Machine Finished End Caps is an advanced solution for superior oil filtration in automotive applications. This filter is designed to offer exceptional protection against oil contamination, ensuring optimal engine performance and longevity.

High-Quality Stainless Steel Construction: Made from medical-grade type 304 stainless steel micronic filter cloth, which filters down to 35 microns and provides a high flow rate of 1.9 gallons per minute per square inch.
Cleanable and Reusable: Unlike paper filters, this stainless steel filter can be washed and reused, offering both cost savings and environmental benefits.
Consistent Filtration: Delivers reliable filtering performance across the entire filter surface, maintaining engine protection.
Superior Filtration Performance: Achieves excellent ASTMF316 filtration standards and includes magnetic prefiltering to capture metallic particles.
Billet Aluminum Filter Case: Acts as an oil cooler (where applicable) and adds durability.
Progressive Rate Bypass: Combined with high flow characteristics, this feature prevents unfiltered oil from bypassing the filter during cold starts and high RPMs.
Easy Contamination Inspection: Allows for straightforward inspection of engine contamination levels.
Proven Track Record: Trusted in motorsports, military, and aerospace applications.

Please note: For older caged-type filters, a newer filter housing is required. Ensure the larger hole insert is installed on the housing cap for proper fitment.

Show More Show Less

K&P Engineering High Performance Stainless Steel Oil Filter - N62 N73...

Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:38419075

Part#: S65

Ships on Nov 13, 2026

$ 159.00 USD

Add to Wish List

Qty

$ 159.00 USD

Add to Wish List

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused! The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat. K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top-tier product for your European vehicle.

Show More Show Less

MINI Cooper K&P Engineering High Performance Stainless Steel Micronic...

Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:30330968

Part#: S35

Ships on Nov 13, 2026

$ 119.00 USD

Add to Wish List

Qty

$ 119.00 USD

Add to Wish List

MMX High Performance Oil Filter - BMW B58 & B58TU

Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:29035359

Part#: MMR17-1502

Special Order: No Guaranteed ETA

$ 81.99 USD

Add to Wish List

Qty

$ 81.99 USD

Add to Wish List

Get rid of the notorious B58 oil filter disintegration problem forevermore with the MMR Performance Oil Filter. By replacing the factory paper filter element with MMR’s advanced high-flow, high-filtration stainless steel filter unit, you will protect your engine from the big bills (and potentially worse) caused by the OE filter’s collapse failure. The oil filters on BMW’s B58 & B57 3.0 6-cylinder engines (both petrol and diesel) suffer from a well-documented quality problem with the factory paper-element oil filter. At service time, when removal of the filter is attempted, the bottom section frequently breaks away from the disintegrated filtration material. This leaves the broken base stuck in the oil filter housing and an expensive removal/replacement job to extract the remains and fit a new housing. Such is the problem that there’s even an official BMW technical bulletin to warn their dealers of this. The MMR replacement Oil Filter is a pretty special replacement filter. It fixes this annoying problem once and for all. The MMR Oil Filter element is made from a pleated high-flow stainless steel micronic filter cloth – a medical-grade material guaranteed to filter out oil contamination right down to 20 Microns, ensuring far better protection than paper-based filters can achieve. As well as this exceptional filtration, the filter material allows for five times the flow of comparable paper oil filters. Its design provides consistent filtering across entire filter surface. The failure of the factory oil filter generally just leads to a large bill to extract the damaged remnants. However, more worryingly, it has occasionally been known to lead to broken pieces of filter media running through the small oilways and orifices of the engine’s lubrication system, risking blocking the oil running round the bearings and VANOS system and causing much greater mechanical damage before it is caught. The MMR Oil Filter is a reusable unit which can be used over and over again. As long as it is thoroughly cleaned at each oil change, it will last the lifetime of the vehicle and keep on protecting the engine just as it did when new. However, proper cleaning is not necessarily a DIY job, as it requires the use of a suitable solvent to break down the old oil, and cleaning from the inside out with compressed air to remove any risk of debris remaining. If you have any doubts about this, we recommend as best-practice to change filter with every oil-change. The MMR Oil Filter is a lifetime reusable filter. But to resuse and avoid any future loss of filtration or oil flow, it is essential that it is thoroughly cleaned at each oil change as follows: Remove MMR Oil Filter from filter housing Remove 3x O-Rings from MMR Oil Filter prior to Step 3, as fuel will degrade and cause damage to these rubber/Viton components. Soak the filter one of the following fluids for 5-10 minutes – Petrol/Gasoline or Carb Cleaner or Soap and Water Agitate/stir every few minutes until the outer surface is free of any engine debris Dry the filter using compressed air, blow air through the filter, (do not press the compressed air gun against the filter, keep at least a 10mm gap from nozzle to filter) starting from the inside out, then at an angle on the outside of the screen to further remove any remaining particles or cleaning solution. Once dry, reinstall O-Rings (MMR advices replacement of these O-Rings every oil service - See ES4810064) and refit into oil filter housing and engine. If you have any doubt about your ability to perform this sequence, we recommend replacing the filter element with each oil change.

Show More Show Less

K&P Engineering High Performance Stainless Steel Oil Filter - M44 M42...

Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:38419076

Part#: S66

In Stock

$ 139.00

This product was last offered at the strikethrough price on
05-03-2026

$ 126.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 139.00

This product was last offered at the strikethrough price on
05-03-2026

$ 126.99 USD

Limited Qty Sale

Add to Wish List

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused! The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat. K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top-tier product for your European vehicle.

Show More Show Less

O-Ring Replacement Kit For MMX Performance Filter - BMW B58 & B58TU ...

Earn 5% back in Turner Rewards on orders placed 10/26/26 - 10/31/26. Redeem 11/26/26 - 12/1/26. Terms & conditions apply

T#:29035360

Part#: MMR17-0000

Special Order: No Guaranteed ETA

$ 13.99 USD

Add to Wish List

Qty

$ 13.99 USD

Add to Wish List

Genuine MMR Performance O-Ring service kit for the MMX Performance oil filter and billet housing. Does not include MMR oil filter or billet housing, only the four O-Rings needed to service our reusable filter. The MMR Performance oil filter and housing contains four O-Rings within the kit. We recommend you replace the O-Ring set on a regular basis when changing or cleaning the MMR filter, in order to maintain the integrity of the sealing properties it was designed to provide. As it's a direct replacement with the original O-Ring set supplied, it's a very straightforward process to swap and replace. Fitment is limited to the MMR Performance oil filter (MMR17-1502 - See ES4810063) to protect against the notorious B58 oil filter collapse

Show More Show Less

Project Cars

SELECT YOUR BMW

K&P Engineering High Performance Stainless Steel Micronic Oil Filter ...

K&P Engineering High Performance Stainless Steel Oil Filter - N62 N73...

MINI Cooper K&P Engineering High Performance Stainless Steel Micronic...

MMX High Performance Oil Filter - BMW B58 & B58TU

K&P Engineering High Performance Stainless Steel Oil Filter - M44 M42...

O-Ring Replacement Kit For MMX Performance Filter - BMW B58 & B58TU ...

Select Vehicle

Purpose

Category

Brand

Price

Shipping

Narrow Results