BMW Suspension Parts

**For vehicles with coilover front suspension**

When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height. 

The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.

Features:

• Decreased understeer
• Decreases outside edge tire wear
• Aircraft Grade Aluminum Construction
• Steel Monoball and Mounting Sleeves

Fits the following BMWs:
1991-1999 E36 BMW

This kit is contains all new strut and shock mounts and hardware needed when installing a new shocks and struts or aftermarket suspension on your vehicle. 

Fits the following BMW's

F22/23 228i 228i xDrive M235i M235i xDrive without EDC and production date up 03/2015 

F30 320i 320i xDrive 328d 328d xDrive 328i 328i xDrive 335i 335i xDrive without EDC and production date up 03/2015 

F32/33/36 428i 428i xDrive 435i 435i xDrive 

If E30 needs a little more pep in the corners, this is an excellent suspension package. H&R Sport springs and Bilstein Sport shocks for the E30 will lower the ride height for an aggressive stance and stiffer springs will improve handling and balance in the corners. This suspension is a favorite among our E30 fans because the car corners better without a punishing ride. Perfect for daily-driven E30s who want to carry more speed through the corners.

H&R Sport springs lower the ride height by 1.25" and stiffens the spring rate. Both combine to lower the car's center of gravity and reduce the amount of bodyroll in corners. The springs are progressive rate so their initial stiffness is actually very compliant and it becomes stiffer as the spring is compressed. This is great for street cars that see bumps and potholes where suspension compliance is key. Overall, they are about 40% stiffer than the stock original springs.

We use Bilstein Sport shocks as the dampers and they feature Bilstein's patented and innovative valving system. With this system, small bumps and impacts are absorbed as they should be. But the shocks stiffen for cornering and other suspension motions. It's the best of both worlds as the shock self-adjusts based on suspension motion. These fit with the stock strut and shock mounts, making for an easy and clean install.
 

Parts list:

• 1 set - H&R Sport Springs (50406)
• 1 pair - Bilstein Front Sport strut inserts (P36-0335 / 34-003350)
• 1 pair - Bilstein Rear Sport Shocks (B36-2027 / 24-020275)

Fitment note: Front strut inserts fit the larger 51mm strut housings. These were standard for all 6-cylinder E30s, all M3, and 1989-1992 318i/is. Other models used a smaller strut housing which requires a different Bilstein insert.

This item fits the following BMWs:
1984-1992 E30 BMW 325e 325es 325i 325ic 325is

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Front Control Arms
Front Control Arm Bushings

**For vehicles with coilover front suspension**

When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height. 

The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.

Features:

• Decreased understeer
• Decreases outside edge tire wear
• Aircraft Grade Aluminum Construction
• Steel Monoball and Mounting Sleeves

Fits the following BMWs:
1999-2006 E46 BMW

These M3 rear guide rod arms are an upgrade for the non-M cars. The stock non-M arms are made from sheetmetal spot welded together at the ends. The arm tends to flex and bend under even moderate cornering loads. Factor in gripper tires and more torque and this arm is inadequate for stability and consistent handling. The M3 arms are one piece of aluminum offering greater strength and with a sealed monoball inner bushing that allows the arm to rotate (instead of twisting).

This package includes:

• Left M3 Guide Rod - 33322283547
• Right M3 Guide Rod - 33322283548

Replacing your struts and shocks? Don't forget the bushings! The rubber mounts for the shocks will go bad over time, especially if you drive hard or the roads are particularly rough. The shock mounts locate the front struts and rear shocks to the car - providing a quiet and vibration-free buffer between the road and the cabin. Shock mounts and bushings can wear out just like any other rubber part on the car. This leads to more noise and harshness reaching the chassis and may complicate your new suspension install. When installing new shocks, that is the perfect time to also replace the mounts. There is no additional time to install them, no special tools required, and doesn't take any extra time! If you re-use the original mounts you have the risk of them failing before your next shock replacement, doubling your labor costs.

Fits the following BMWs:
2014-03/2015 F22 BMW 228i 228iX M235i M235iX - vehicles without EDC
2012-03/2015 F30 BMW 320i 320iX 328i 328iX 335i 335iX - Sedan - vehicles without EDC
2014-03/2015 F34 BMW 328i 328iX 335iX - Gran Turismo - vehicles without EDC
2014-03/2015 F32 BMW 428i 428iX 435i 435iX - Coupe - vehicles without EDC
2014-03/2015 F33 BMW 428i 428iX 435i 435iX - Convertible - vehicles without EDC
2014-03/2015 F36 BMW 428iX 435iX - Gran Coupe - vehicles without EDC

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Front Control Arms
Front Control Arm Bushings
Front Sway Bar End Links & Bushings
Front Ball Joints
New Hardware

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Rear Sway Bar End Links
Rear Trailing Arm Bushings
Rear Strut Mounts
New Hardware

A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides. 

The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.

Easily installed with basic hand tools.

Fits the following BMW chassis:
E30 BMW All Submodels