BMW Suspension Parts

If you are looking for a wider range of camber adjustability in the rear of you car, the IRP Adjustable rear lower control arm is exactly what you need! Built to be much stronger than stock, these rear control arms feature inner monoball bushings and are built of steel, reducing the weight as well. These are perfect for a lowered car or for a track car that needs a greater level of rear adjustment.

Features:

• Strong Steel Construction
• Adjustable
• Painted Yellow For Corrosion Protection
• Weight Reduction
• Monoball Inner Mount

This item fits the following BMWs:
1992-1999 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

**For vehicles with coilover front suspension**

When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height. 

The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.

Features:

• Decreased understeer
• Decreases outside edge tire wear
• Aircraft Grade Aluminum Construction
• Steel Monoball and Mounting Sleeves

Fits the following BMWs:
1991-1999 E36 BMW

**For vehicles with coilover front suspension**

When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height. 

The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.

Features:

• Decreased understeer
• Decreases outside edge tire wear
• Aircraft Grade Aluminum Construction
• Steel Monoball and Mounting Sleeves

Fits the following BMWs:
1999-2006 E46 BMW

A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides. 

The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.

Easily installed with basic hand tools.

Fits the following BMW chassis:
E46 BMW All Submodels

Replacement REAR sway bar / swaybar link for all 1997-2003 5 series sedans and wagons. Made by Meyle, this is a very common wear item in the E39 suspension, especially when the car has been driven hard. While replacing this part, also check the sway bar bushing bracket for signs of stress or failure. It can be used on both the left and right side of the car. Two required per car, and are sold individually.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i M5

Strut mounts can begin to wear and fail over time, causing a knock in the suspension to occur. Replace yours with a high-quality Meyle replacement to ensure a tight, noise-free ride.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

The front control arm bushings is the Achilles heel on the E39 models. The original factory bushings are fluid filled and rely on the fluid to absorb vibration and resist deflection. When the fluid is gone the rubber left over cannot match the original bushing's strength. The left over rubber is not stiff enough to resist the movements from the suspension. The result is a lot of vibration and reduced feedback and response from the steering.

Meyle has addressed this issue with bushings that are not fluid-filled. The bushing is made of solid rubber that will last longer than the original bushing and is a bit stiffer than new originals for better response and feel. The lack of play from the solid rubber design will mean sharper steering, restoring much of the car's precision and 'connected' feel.

This is a package of Meyle HD control arms with the HD bushings already pressed in. This makes for an easy swap out-swap in install. These arms replace the existing stock upper control arms - otherwise known as a tension strut or strut support arm. It's the arm with the twist. The BMW part numbers for these arms are 31 12 1 141 717 and 31 12 1 141 718.

Meyle is a German brand in business since 1958 and all of their products are TUV approved and meet or exceed ISO standards. All Meyle HD parts come with a 4-year, unlimited mileage warranty.

Features:

• 4 Year Warranty

• All metal ball joints are more reliable and longer lasting than stock

• Bushings are solid rubber rather than fluid filled, providing longevity and handling feel improvements

This item fits the following BMWs:
1997-2003 E39 5 Series BMW 525i, 525iT, 528i, 528iT, 530i sedans and touring wagons
2000-2003 E52 Z8 Z8 - Z8 Alpina