Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints(M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability

Due to their soft rubber construction, OE strut mounts are known to wear at an accelerated rate. Many high-mileage vehicles fall victim to strut mount failure, which is commonly associated with annoying clunks, groans, or rattles from the front suspension.

With this issue in mind, ECS Tuning developed their heavy-duty front strut mount with upgraded, higher durometer rubber to resolve sloppy handling and increase longevity. Manufactured precisely within OEM tolerances, these mounts are a perfect fit for your MINI.

Features:

Reduces deflection: Increases vehicle handling and cornering dynamics by removing deflection within the strut mount. Increases longevity: Upgraded rubber construction makes for a stiffer mount, less prone to cracking and general degradation. Developed in-house: Designed and tested by ECS Tuning engineers, this mount is sure to outlast an OE replacement. Upgrade to a better strut mount without sacrificing ride comfort! Improve longevity and ride control all at once.

Fine-tuning your coilover damping shouldn’t mean stripping out your rear seats or interior panels. On many applications, rear shock adjusters are hidden behind carpet, trim, or seatbacks, making quick adjustments a hassle.

The ECS Rear Damping Extension Kit solves that problem with a clean and functional solution. These flexible extensions relocate the adjustment knobs to an easily accessible point above the rear shock towers, letting you dial in your suspension from inside the cabin, no disassembly required.

Installation is straightforward: simply drill a small access hole in your interior trim and route the extension cables through. The adjustment knobs can be removed to allow the line to pass through smaller openings, minimizing cutting. For proper installation, be sure to fully loosen the set screw, insert the cable, then securely tighten it using the provided Allen key.

Kit Includes:

(2) Rear damping adjuster extension cables

Installation hardware and Allen key

A smart upgrade for track cars, daily drivers, or anyone who values easy access to suspension tuning, without compromising interior fit and finish.

The ECS Strut Tower Bar Kit in striking wrinkle black finish goes beyond aesthetics - it offers essential functionality. This kit significantly reduces chassis flex, contributing to a stiffer suspension setup. Moreover, it plays a crucial role in triangulating the front end, resulting in more consistent suspension geometry that enhances your vehicle's performance.

It's essential to ensure that the strut tower plates sit flush against the strut towers. Any misalignment may indicate minor deformations in your strut towers. However, this can be easily addressed using a block of wood and a hammer to reinstate the ideal alignment.

Due to their soft rubber construction, OE strut mounts are known to wear at an accelerated rate. Many high-mileage vehicles fall victim to strut mount failure, which is commonly associated with annoying clunks, groans, or rattles from the front suspension.

With this issue in mind, ECS Tuning developed their heavy-duty front strut mount with upgraded, higher durometer rubber to resolve sloppy handling and increase longevity. Manufactured precisely within OEM tolerances, these mounts are a perfect fit for your BMW.

Features:

Reduces deflection: Increases vehicle handling and cornering dynamics by removing deflection within the strut mount. Increases longevity: Upgraded rubber construction makes for a stiffer mount, less prone to cracking and general degradation. Developed in-house: Designed and tested by ECS Tuning engineers, this mount is sure to outlast an OE replacement. Upgrade to a better strut mount without sacrificing ride comfort! Improve longevity and ride control all at once.

The ECS Tuning Billet Front Sway Bar Mounting Kit will provide your vehicle with a more rigid mounting solution from the sway bar to chassis than the OEM steel brackets. With an improved sway bar mounting bracket and the included polyurethane sway bar bushings you can expect to achieve an increase in rear sway bar effectiveness and less body roll as a result.

PART DESIGN

The front sway bar mounting brackets are made from a solid piece of 6061-T6 billet aluminum that are precision CNC-machined to bolt into the OEM mounting location while utilizing greaseable, polyurethane bushings. They are Type II black anodized for corrosion protection and include zinc flake coated Class 12.9 alloy steel bolts for premium performance.

The red polyurethane bushings feature a greaseable channel for extended service life and quieter operation than standard polyurethane bushings.

PERFORMANCE FEATURES

Billet & poly mounts replacing the OEM steel & rubber configuration you can expect faster reaction speed and greater effectiveness from your front sway bar due to less deflection. This translates to better handling with sharper, flatter cornering with reduced body roll.

PRODUCT DEVELOPMENT

ECS Billet Front Sway Bar Mounting Kit was designed, engineered, tested and quality inspected by the Research and Development team in our Wadsworth, Ohio facility to ensure the highest level of precision and quality is delivered throughout rigorous long term product testing and leading edge product development methods.

INSTALLATION AND SUPPORT

Installation is simple. Simply unbolt your front sway bar mounting brackets and slip over our poly bushings and billet mounting brackets with the included hardware. That's it! Enjoy better handling and a crisp front suspension.

SPECIAL NOTE: You can use any conventional automotive bearing grease for service.

Elevate your driving experience with enhanced performance and aesthetics. ECS lowering springs are crafted to optimize both handling and comfort, striking the perfect balance between performance and drivability. With an average lowering range of 1.6", enjoy the benefits of a lower center of gravity, resulting in superior cornering and enhanced steering feedback. Not only do these lowering springs improve handling, but they also deliver a remarkable aesthetic transformation by reducing the wheel gap, giving your car a more planted and fitted appearance.

The example pictures shown are of both xDrive(Red F22) and Rwd(Blue F22)

Features and Design:

Average FRONT lowering of 1.0" - 1.4"
Average REAR lowering of 1.2" - 1.6"
Lowered center of gravity
Compatible with cars equipped with EDC
Linear style springs
Black powder coating with red ECS logo
MADE IN THE USA
Designed specifically for your chassis these ECS lowering springs feature a linear style spring similar to a coilover. The issue with coilovers is the rough ride due to a drastic drop and much higher spring rates. When you have a higher spring rate like coilovers, it takes much more force to compress the spring, leading to a much more rigid ride. ECS lowering springs provide a happy medium between the factory suspension and coilover suspension. Our springs are stiffer than factory but softer than a coilover spring to achieve the balance of increased performance and aesthetics while retaining a comfortable ride.

Enhance your MINI's performance with the NM RSα progressive rate spring kits, delivering a more responsive ride, improved handling, and a lowered ride height. These springs are engineered with precise spring rates and manufacturing methods, offering an elevated motoring experience.

Key Benefits:

• Responsive ride quality
• Sharper handling characteristics
• Lowered ride height for improved aesthetics

The ECS Tuning Billet Front Sway Bar Mounting Kit will provide your vehicle with a more rigid mounting solution from the sway bar to chassis than the OEM steel brackets. With an improved sway bar mounting bracket and the included polyurethane sway bar bushings you can expect to achieve an increase in rear sway bar effectiveness and less body roll as a result.

PART DESIGN

The front sway bar mounting brackets are made from a solid piece of 6061-T6 billet aluminum that are precision CNC-machined to bolt into the OEM mounting location while utilizing greaseable, polyurethane bushings. They are Type II black anodized for corrosion protection and include zinc flake coated Class 12.9 alloy steel bolts for premium performance.

The red polyurethane bushings feature a greaseable channel for extended service life and quieter operation than standard polyurethane bushings.

PERFORMANCE FEATURES

Billet & poly mounts replacing the OEM steel & rubber configuration you can expect faster reaction speed and greater effectiveness from your front sway bar due to less deflection. This translates to better handling with sharper, flatter cornering with reduced body roll.

PRODUCT DEVELOPMENT

ECS Billet Front Sway Bar Mounting Kit was designed, engineered, tested and quality inspected by the Research and Development team in our Wadsworth, Ohio facility to ensure the highest level of precision and quality is delivered throughout rigorous long term product testing and leading edge product development methods.

INSTALLATION AND SUPPORT

Installation is simple. Simply unbolt your front sway bar mounting brackets and slip over our poly bushings and billet mounting brackets with the included hardware. That's it! Enjoy better handling and a crisp front suspension.

SPECIAL NOTE: You can use any conventional automotive bearing grease for service.

Improve your BMW's suspension and alignment precision with Godspeed Project's Rear Trailing Arms. Designed to combat poor road or track conditions, these trailing arms offer stability and reduced tire wear, enhancing vehicle handling.

Key Benefits:

• Precise alignment adjustment for stability at high speeds
• Solid spherical bushings resist wear, ensuring durability
• Heat-treated ball and hard chrome plated alloy steel construction for strength
• Stainless steel race with PTFE fabric lining provides self-lubrication, minimizing wear
• Affordable performance upgrade with increased adjustment ranges and versatility
• Solid design offers improved road feel and handling feedback

Ensure optimal performance and alignment with Godspeed Project's Rear Trailing Arms, ideal for track use to enhance suspension reinforcement.

Upgrade your BMW's suspension with BMW E8X E9X Replacement Bushings.

Engineered for durability and performance, these bushings provide improved handling and responsiveness. Specifically designed for BMW E8X and E9X models, they ensure a precise fit and reliable performance. Reduce vibrations and enhance driving comfort with these high-quality replacement bushings.

• Improved handling and responsiveness
• Specifically designed for BMW E8X and E9X models
• Precise fit for reliable performance
• Reduces vibrations for enhanced driving comfort
• High-quality construction for durability

When high torque loads and aggressive corner exits push your chassis to the limit, stock differential mounts quickly become the weak link. The ECS Tuning Rear Differential Front Mount Upgrade Kit is track-engineered to lock down your rear diff, control axle wrap, and ensure immediate power delivery to the pavement.

Built to withstand severe track abuse, this kit eliminates hardware failure by replacing the undersized factory M12 bolt with an ultra-high-tensile Grade 12.9 M14x1.5 bolt. Surrounding the upgraded hardware is a track-spec 95A durometer red polyurethane bushing and a rugged 6061-T6 aluminum sleeve finished in Type II black anodizing. Engineered for maximum drivetrain stiffness, this upgrade ensures your differential stays precisely aligned under the harshest motorsport conditions.

Note: Upgrading to M14x1.5 hardware requires drilling and tapping the original M12x1.5 differential mounting hole. See T#58563042 for a complete kit that includes the proper-sized drill and tap.