Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
This product was last offered at the strikethrough price on
06-10-2026
This product was last offered at the strikethrough price on
06-10-2026
Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.
This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 BMW M6
Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media blasting of the intake valves to strip away the oily buildup we have seen.
Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. The Burger Tuning oil catch can is the best we have seen so far. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine.
The BMS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The BMS OCC also has a factory-like appearance. Since BMS designed their catch can from scratch they can guarantee it fits and performs correctly for the N54/N55 engine, unlike other catch cans on the market that are poorly retrofitted from other applications and under-sized for the N54 engine.
Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles
BMS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ Double-baffled design allows excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Stealth mounting on cooler side of engine bay (promotes condensation of oil to vapor)
+ Anodized black lightweight aluminum
+ N54 version mounts out of sight under the cowl
+ Made in USA with a lifetime guarantee
This product was last offered at the strikethrough price on
08-13-2026
This product was last offered at the strikethrough price on
05-07-2026
This product was last offered at the strikethrough price on
05-03-2026
Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media blasting of the intake valves to strip away the oily buildup we have seen.
Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. The Burger Tuning oil catch can is the best we have seen so far. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine.
The BMS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The BMS OCC also has a factory-like appearance. Since BMS designed their catch can from scratch they can guarantee it fits and performs correctly for the N54/N55 engine, unlike other catch cans on the market that are poorly retrofitted from other applications and under-sized for the N54 engine.
Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles
BMS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ Double-baffled design allows excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Stealth mounting on cooler side of engine bay (promotes condensation of oil to vapor)
+ Anodized black lightweight aluminum
+ N54 version mounts out of sight under the cowl
+ Made in USA with a lifetime guarantee
Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media blasting of the intake valves to strip away the oily buildup we have seen.
Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. The Burger Tuning oil catch can is the best we have seen so far. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine.
The BMS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The BMS OCC also has a factory-like appearance. Since BMS designed their catch can from scratch they can guarantee it fits and performs correctly for the N54/N55 engine, unlike other catch cans on the market that are poorly retrofitted from other applications and under-sized for the N54 engine.
Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles
BMS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ Double-baffled design allows excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Stealth mounting on cooler side of engine bay (promotes condensation of oil to vapor)
+ Anodized black lightweight aluminum
+ N54 version mounts out of sight under the cowl
+ Made in USA with a lifetime guarantee
This item fits the following BMWs with the N54 twin-turbo engine:
2008-2010 E82 BMW 135i
2007-2010 E9X BMW 335i 335xi
2006-2010 E60 BMW 535i 535xiThis item fits the following BMWs with the N54 twin-turbo engine:
2008-2010 E82 BMW 135i
2007-2010 E9X BMW 335i 335xi
2006-2010 E60 BMW 535i 535xi
Ferrea valve springs are developed from high strength alloys, including premium grade chrome silicone steel These springs are manufactured with state-of-the-art equipment. Ferrea springs are heat-treated and stress-relieved, which dramatically increases the spring's life. Strict quality control procedures and cycle testing ensures consistency from batch to batch. Ferrea valve springs provide the stability needed for high lift, high rpm racing and street car engines. Kit includes a set of 24 springs. MUST be used with the Ferrea Spring Seat and Titanium Retainers. See links below.
https://www.turnermotorsport.com/e/p-163-e36-325-328-m3-ferrea-spring-seat-set/
https://www.turnermotorsport.com/e/p-31-e36-325-328-m3-ferrea-titanium-retainer-set/
This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i