Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

Key components to help get your install done easily and effectively. Get your car running right again!

Kit includes:​

• All required gaskets and o-rings
• All exhaust and downpipe gaskets
• T-bolt clamps
• 1gal of Coolant

JM Turbo Cooper - Extreme GTD47 K04 Turbocharger Upgrade

JM Turbo Cooper offers the Extreme GTD47 K04 turbocharger upgrade designed to deliver outstanding reliability and high-performance gains for the 2007+ MINI Cooper. This upgrade is a top choice for Mini and Peugeot owners, providing exceptional power output for applications exceeding 280hp.

Update: The improved gasket design on the back side now features a seamless gasket inset, and the package includes a new gasket for your convenience.

The JMTC Extreme GTD47 upgrade boasts a high-pressure, high-flow, dual-scrolling turbo that features a substantial 50mm compressor wheel. This design ensures maximum boost at the top end of the RPM range, making it ideal for track, off-road, and extreme street applications. The large GTX exhaust turbine complements the setup, delivering extra boost at high RPMs and preventing torque loss compared to the stock K03 turbine.

Whether you seek extreme track performance, drag strip dominance, or unrivaled street upgrades, this turbocharger is the perfect choice. It offers impressive torque and durability, outperforming many other options on the market. To fully unleash its potential, we recommend pairing it with one of our aftermarket exhaust systems.

It's important to note that to harness the additional power, a custom tune is required. Running without a tune will result in minimal to no HP gain.

Estimated Power Gains:

• Approximately 60hp with a tune, intercooler, downpipe, cold air intake, new plugs, basic maintenance, and carbon blasting/cleaning.
• 120hp or more with all the above modifications, plus a ported head, larger valves, ICE pipe, intercooler, and a 3"+ or larger exhaust system.

Extreme GTD Upgrade Features:

• Brand new turbo!
• 47mm billet compressor
• High-flow GTX exhaust turbine
• High-strength K04 internals
• Upgraded 360-degree bearing
• Designed for higher pressure
• High-temperature alloy turbine housing
• Dual-scrolling turbine housing
• Water-cooled bearing housing

For engine and turbocharger reliability, JMTC recommends a 3.0" or larger downpipe/exhaust size for the GTD turbochargers. Please avoid using the stock downpipe or stock-sized catalytic converter.

The OEM intake boot can be used with the removal of the inner sleeve for N14 engines. For N18 engines, the OEM boot at the turbo connection will need to be heated and expanded slightly, which can be done with a heat gun. This turbocharger also fits AEM intake, NM Eng intake, and Forge Intake (Boot). Please note that the hose might need to be warmed and stretched over with a hose expander.

Super SF56 Upgraded Turbocharger - New by JM Turbo Cooper is the ultimate performance upgrade for BMW enthusiasts. Engineered for both street and track use, this turbocharger features a massive 50mm compressor and upgraded 9-blade lightened high-flow turbine. It delivers quick full boost and significant power gains throughout the RPM range, maintaining quick response and enhancing torque and power over the original turbo.

• Massive 50mm billet compressor for increased airflow
• Upgraded 9-blade lightened turbine for improved performance
• High-strength internals and upgraded 360-degree bearing
• Designed for higher pressure and temperature alloy turbine housing
• Water-cooled bearing housing for durability
• Quick spooling dual scrolling housing for optimal response

Upgrade your BMW with the Super SF56 Upgraded Turbocharger for unparalleled performance and power gains.