BMW Fuel System Parts

ARC Upgraded Fuel Pump Control Module - Dual Ball Bearing Fan - EKPM3...

T#:28304525

Part#: EKP-HW05-E-SF

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half bridge IC. When the half bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. I have an EKPM2, can I upgrade to this? Yes. You can upgrade to this. We recommend using the HW05 and below module. You will need to code it in order for it to function properly. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

Upgraded Fuel Pump Control Module - Dual Ball Bearing Fan - EKPM3 ...

T#:28304531

Part#: EKP-HW06-F-SF

In Stock

$ 209.99 USD

Add to Wish List

Qty

$ 209.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half-bridge IC. When the half-bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

BMW F Chassis Upgraded Fuel Pump Control Module - Noctua Fan - EKPM3 ...

This service will not work for M-Cars or any B-Series motors

T#:28304534

Part#: EKP-HW06-F-NF

In Stock

$ 239.99 USD

Add to Wish List

Qty

$ 239.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. Includes 40mm Noctua Silent Fan! How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half-bridge IC. When the half-bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

Port Injector Plugs

T#:27171925

Part#: UNI-BMS-PIPLUGS

In Stock

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

These dummy injectors fit in place of port injection fuel injectors to block the holes. Allows use to aluminum manifolds with port injection bungs without having to purchase fuel injectors. Plugs are EV14 injectors and measure 38mm or 1.5" from o-ring to o-ring.

Show More Show Less

Bav Auto Fuel Level Sensor & Fuel Pump Lock Ring Tool - BMW & MINI ...

T#:580400

Part#: B8800089

Ships on Sep 1, 2026

Sale - Save 10% $ 72.99

This product was last offered at the strikethrough price on
05-03-2026

$ 65.69 USD

Add to Wish List

Qty

Sale - Save 10%

$ 72.99

This product was last offered at the strikethrough price on
05-03-2026

$ 65.69 USD

Add to Wish List

Used to remove fuel level and fuel pump lock rings properly to avoid damage.

F3X/F2X - N20 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471604

Part#: AT226F22BLA501N2

Ships in 2 Business Days

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan or 60mm Noctua Fan (depending on choice) 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

F3X/F2X - N55 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471608

Part#: AT223F22BLA501N5

Ships in 2 Business Days

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

Upgraded EKPM3 Fuel Pump Control Module - Noctua Fan

T#:28304530

Part#: EKP-HW05-E-NF

Back Ordered

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. Includes 40mm Noctua Silent Fan! How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half bridge IC. When the half bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. I have an EKPM2, can I upgrade to this? Yes. You can upgrade to this. We recommend using the HW05 and below module. You will need to code it in order for it to function properly. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

E90 / E92 / E93 Silent Fan EKP PNP Cooler Kit - 40mm Noctua Fan ...

A Must For Cars With Upgraded LPFPs

T#:26404814

Part#: SILENT-E90-EKP

Ships in 2 Business Days

Starting at $ 59.99 USD

Add to Wish List

Starting at $ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E9X BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8 (2007+ E9X), which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put it into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable ASA, ABS, or PETG. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With a Genuine Noctua 60mm or 40mm Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a silent Noctua fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E90 / E92 / E93 EKP PNP Cooler Kit - (3 Series)

A Must For Cars With Upgraded LPFPs

T#:26271821

Part#: E9X-EKP-PNP

Ships in 1 Business Day

Starting at $ 44.99 USD

Add to Wish List

Starting at $ 44.99 USD

Add to Wish List

This fully plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E9X BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. If you have an M3, you must choose an EKPM2 style cooler since the EKP Module has the same physical dimensions as an EKPM2. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8 (2007+ E9X), which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature. Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse

Show More Show Less

F8X - S55 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471618

Part#: AT225F22BLA501S5

Ships in 2 Business Days

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F80, F82, F83, and F87 (Comp) BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

B58 Supra Fuel Pump Retrofit Extension Harness - F3X B58

T#:2810078

Part#: B58PUMPHARNESS

In Stock

$ 45.00 USD

Add to Wish List

Qty

$ 45.00 USD

Add to Wish List

Use this harness to run an improved "Supra" fuel pump in your B58 car. This harness allows you to run the G20 M340i/Supra Fuel pump (13518631642) on your F Chassis B58 car.

F3X/F2X - N55 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471609

Part#: AT231F22BLA40MN5

Ships in 2 Business Days

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a single 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E82 Silent Fan EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471523

Part#: SILENT-E82-EKP

Ships in 1 Business Day

Starting at $ 59.99 USD

Add to Wish List

Starting at $ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E82 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8 (2007+ E82), which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With a Genuine 60mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a silent Noctua fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E60 / E61 EKPM2 EKPM3 PNP Cooler Kit - (5 Series)

A Must For Cars With Upgraded LPFPs

T#:26305056

Part#: E60-EKP-PNPC

Ships in 1 Business Day

Starting at $ 59.99 USD

Add to Wish List

Starting at $ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E60 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. There are two versions of the kit, one with a relay and one without a relay. The relay kit is for those who would prefer to not put an additional load on their 12v outlet circuit due to using that circuit for something with a high load already. The non-relay kit will work perfectly for any normal use of the 12v outlet circuit and only adds up to 0.30 amps onto that circuit, which is very minimal. For all M5s, you will need to use an EKPM2 kit as the EKP module is physically the same size as an EKPM2. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan and Fused Relay 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 2x 2 Amp Standard Blade Fuses Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E82 / E88 EKPM2 EKPM3 PNP Cooler Kit - (1 Series)

A Must For Cars With Upgraded LPFPs

T#:26404802

Part#: E82-EKP-PNPC

Ships in 1 Business Day

Starting at $ 44.99 USD

Add to Wish List

Starting at $ 44.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E82 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. 10% of all proceeds from pink housings sold will be donated towards Breast Cancer research. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8 (2007+ E82), which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. We also offer a DIY kit that includes everything you'll need to create your own active cooling solution here: https://arcterminator.com/products/ekp-active-cooling-diy-kit The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable ASA, ABS or PETG, depending on the color choice. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

F3X/F2X - B58 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471614

Part#: AT232F22BLA40MB5

Ships in 2 Business Days

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a single 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

F3X/F2X - N20 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471605

Part#: AT234F22BLA40MN2

Ships in 2 Business Days

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a single 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

MTX-D: Ethanol Content % And Fuel Temperature Gauge

T#:22558994

Part#: INN3904

In Stock at Vendor

14% off MSRP $ 313.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 269.00 USD

Add to Wish List

Qty

14% off MSRP

$ 313.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 269.00 USD

Add to Wish List

Introducing the Innovate Motorsports MTX Digital Series "Dual Function" Gauges – now available! These 2 1/16" (52mm) gauges come with interchangeable faceplates and bezels, locking connectors for simplified installation, and MTS serial connections for seamless integration with other Innovate devices for data logging.

DISPLAY RANGE

Ethanol Content %: 0-100%
Temperature: -40-257 °F (-40-125°C)

KEY FEATURES

Ethanol Content
Error reporting for ethanol content sensor (Digital Display)
Fuel Temperature
Customizable exterior LED display
Programmable exterior LED color options
Selectable unit of measure in °F or °C
Programmable fuel temperature warning (outer LED)
2-Configurable analog outputs
Ethanol Content: 0v = 0%, 5v = 100%
Fuel Temperature: 0v = -40 °F, 5v = 257 °F (-40-125°C)

MTX-D: Ethanol Content Percentage & Fuel Temp Gauge Kit includes Gauge (Black Faceplate, Black Bezel), Silver Bezel & White Faceplate, Harness, Program Cable (Serial), Ethanol Content Sensor, Quick Start Installation Guide.

Please note that this is a universal fitment gauge, and installation may vary depending on the vehicle.

Show More Show Less

G8X S58 Flex Fuel Kit

T#:8061332

Part#: S58FLEXFKIT

Ships on Aug 31, 2026

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

This complete flex fuel kit installs in under 30 minutes and reads your exact E85 mixture in the Fuel-It! smartphone app or JB4 app if equipped. Features CNC machined fittings for a quick plug and play installation with nylon sleeved stainless steel braided fuel lines for life long leak free operation. The complete kit includes the following: Genuine Continental ethanol sensor Fuel-It! Bluetooth Universal Analyzer Two stainless steel braided fuel lines with black nylon sheathing to protect your other engine bay components Proprietary custom billet fittings for plug and play OEM integration One wiring harness with Posi-tap connector Supports stand-alone Bluetooth operation with the Fuel-It! app **For the BMW G-series JB4 platform connect the white wire to position #4 on the JB4 25 pin harness. Select WMI page option 2/3/4 input to enable.

Show More Show Less

F3X/F2X - B58 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471615

Part#: AT224F22BLA501B5

Ships in 2 Business Days

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

Fuel-It! Low Pressure Fuel Pump Upgrade Stage 3 - N54/55 E-Series ...

T#:403279

Part#: FILPFPK3

Back Ordered

Starting at $ 1,154.83 USD

Add to Wish List

Starting at $ 1,154.83 USD

Add to Wish List

This is a complete Low-Pressure Fuel Pump (LPFP) upgrade that replaces your stock LPFP assembly with a new E85 certified one. This solution provides up to 300% more flow than stock and this assembly can be purchased one of three ways to meet your needs. Trade-in: (Domestic and Canada) This option allows you to receive a rebuilt/upgraded stock bucket with two new Walbro 450 pumps, filters, and fittings to swap out your stock LPFP assembly and requires a $150 *core deposit. Trade-in: (Euro) This option allows you to receive a rebuilt/upgraded stock bucket with two new Walbro 450 pumps, filters, and fittings to swap out your stock LPFP assembly and requires a $300 *core deposit. New Build: This option includes a new VDO LPFP bucket that is upgraded with new Walbro 450 pumps, filters, and fittings. No core deposit required but is eligible for a core refund of $50 should you elect to return your *stock bucket. (US Spec only) All three options include the following: A complete plug and play solution by simply replacing your stock bucket. However, to utilize the secondary, an additional wiring harness must be installed. Two new E85 compatible Walbro 450 pumps Two new Walbro filters A custom fitting that is tuned to optimize the venturi and pump output Spare vent tube clip Wiring harness for the secondary Flow testing prior to shipping

Show More Show Less

Fuel-It! B58 BMW High Pressure Fuel Pump (HPFP) Upgrade - Stage 1 ...

T#:17106920

Part#: BMW-B58HPFP-A01

Ships on Aug 31, 2026

$ 1,499.00 USD

Add to Wish List

Qty

$ 1,499.00 USD

Add to Wish List

Introducing the new B58 BMW HPFP upgrade kit from Fuel-It! Replaces your factory high-pressure fuel pump with a higher capacity pump capable of supporting 30% more flow with Stage1 or 60% more flow with Stage2! Includes all required installation hardware for a clean plug and play install. Includes: Upgraded High-Pressure Fuel Pump (HPFP) Billet Adapter Plate Billet Center Alignment Tool Low-pressure Line (Triple lined crimped fittings PTFE/SS/Nylon Braided) Custom Harness and Hardware

Show More Show Less

F8X - S55 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471619

Part#: AT233F22BLA40MS5

Ships in 2 Business Days

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F80, F82, F83, and F87 (Comp) BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a Single Noctua 40mm Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

Fuel-It! F-Chassis B58 Stage 3 LPFP Upgrade

T#:17837993

Part#: B58STG3LPFP

Back Ordered

$ 829.99 USD

Add to Wish List

Qty

$ 829.99 USD

Add to Wish List

This is a complete Low Pressure Fuel Pump (LPFP) upgrade for those customers that need the additional capacity to meet their power goals on pump gas, race gas, or E85. It utilizes a stock pump for the primary pump so that your EKP operates as intended by the factory eliminating potential errors for current draw and the secondary pump then runs under high boost only. For power levels up to 700whp we'd recommend using the standard 450 pump and beyond 700whp we'd recommend upgrading to the 525 pump. F-Series B58 (Gen 1) Stage 3 assemblies include: New stock LPFP Secondary pump assembly Secondary wiring harness Walbro filter Walbro 450 pump (F90000274) Compatible with the following vehicle production dates: 1' F20 LCI (05/2014 — 06/2019) 1' F21 LCI (05/2014 — 06/2019) 2' F22 (06/2014 — 06/2017) 2' F22 LCI (09/2016 — 12/2019) 2' F23 (06/2014 — 06/2017) 2' F23 LCI (09/2016 — 12/2019) 3' F30 LCI (09/2014 — 10/2018) 3' F31 LCI (09/2014 — 06/2019) 3' F34 GT LCI (09/2015 — 12/2019) 4' F32 (04/2015 — 02/2017) 4' F32 LCI (05/2016 — 12/2019) 4' F33 (03/2015 — 02/2017) 4' F33 LCI (05/2016 — 12/2019) 4' F36 Gran Coupé (05/2014 — 03/2017) 4' F36 Gran Coupé LCI (05/2016 — 12/2019) *Note: Secondary pump can NOT run full time. We recommend using a Hobb's switch to trigger the secondary under high boost. See the installation process here: https://www.youtube.com/watch?v=YoPf0F7PBt8

Show More Show Less

Fuel-It! FLEX FUEL KIT For S58 BMW X3M & X4M - Complete Kit With Blue...

T#:15976528

Part#: S58X3MFFK-BTECA

Ships in 3 Business Days

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

This is a complete plug-and-play kit to install a Bluetooth ethanol sensor in your X3M or X4M in about 30 minutes. The kit includes the following: New 5/16" E85 compatible fuel lines for your engine bay Genuine Continental ethanol sensor Fuel-It! Bluetooth Universal Analyzer (view E85 mix via Fuel-It! app) OR CANflex ECA (no Fuel-It! app support without the Bluetooth ECA), view E85 mix via JB4 or flash logging) Plug-and-play harness Includes both Bluetooth App & 5v analog output for JB4 or flash tunin This kit is compatible with the following 2020+ BMW X3M / X3M Competition 2020+ BMW X4M / X4M Competition *For the BMW S58 JB4 platform connect the white wire to position #4 on the JB4 25 pin harness. Select WMI page option 2/3 input to enable. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Stage 2 LPFP Upgrade & Lock-Ring Removal Tool - G-Chassis B58 B46 ...

T#:25075820

Part#: BX8LPFPS2LRRT

Ships in 8 Business Days

$ 619.00 USD

Add to Wish List

Qty

$ 619.00 USD

Add to Wish List

Finally, a quality low-pressure fuel system upgrade worthy of installing in your B58-equipped G-Chassis BMW! This drop-in bucket assembly replaces the factory fuel-sending unit, supports ethanol fuel and up to 700 wheel horsepower!

Show More Show Less

Fuel-It! 650HP S65 E9X BMW M3 LPFP Upgrade - w/ 4PSI Hobbs Switch ...

T#:18202901

Part#: FIS65M3LPFP

Back Ordered

$ 514.00 USD

Add to Wish List

Qty

$ 514.00 USD

Add to Wish List

As these cars get older we're seeing more issues with the stock components and more demand for cost-conscious fueling solutions. The new Fuel-It 650HP line of fuel system upgrades are designed with those needs in mind while maintaining a budget. They make the most of the stock components to maintain stock reliability and drive-ability but when the boost gets cranked up, the Fuel-it 650HP components kick in to support the additional fueling needs of your high horsepower car. With the Fuel-It 650HP lineup, you can upgrade your components all at one time or upgrade them as time and budget allows. If upgrading one component at a time, we'd recommend starting with the LPFP first as that is the heart of your fuel system, without a good Low Pressure Fuel pump (LPFP) you can't supply the fuel needed to any of your other components. Your secondary pump can NOT run full time, it must only be run under boost only. Running it full time will place additional strain on the stock system, will lead to high fuel temps, and pump or component failure. To turn the secondary pump on under boost we recommend running the included 4psi Hobb's switch. Included with all S65 LPFP upgrades: Walbro 450 pump (F90000274) Black Anodized Custom fitting Pump brackets 9/64" terminals and associated hardware Fuel line Replacement PITA clip Wiring harness

Show More Show Less

JB4PRO Flex Fuel Add On Harness - B58/S58

T#:49822568

Part#: JB4PB58FFAOH

In Stock

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

Take your B58 or S58 build further with the JB4PRO Flex Fuel Add-On Harness—a simple, plug-and-play way to add an ethanol sensor and optional fuel pressure sensor to your JB4PRO setup. Keep your install clean, your wiring organized, and your tune dialed to match every fuel blend in the tank. Why it matters: Plug & Play: Connects directly to your JB4PRO—no cutting or splicing required. Sensor Ready: Supports ethanol and fuel pressure sensors for precise, real-time fueling adjustments. Clean, Safe Installation: Includes a 12 V adapter and inline fuse for hassle-free integration. How it works: This harness links your JB4PRO tuner to your flex fuel hardware. It’s not a complete flex fuel kit—you still need a compatible ethanol sensor—but it gives your JB4PRO the accurate readings it needs to adjust timing, boost, and fueling for E30, E50, or E85 blends.

Show More Show Less

Fuel-It! Flex Fuel Kit - N54/N55 E Chassis

T#:21242695

Part#: FFK-N5XA

In Stock

Starting at $ 485.99 USD

Add to Wish List

Starting at $ 485.99 USD

Add to Wish List

If you are running E85 or ethanol mixes in your BMW, you need this kit! This is a complete plug and play kit to install a Bluetooth ethanol sensor in your E-Chassis BMW. This kit replaces the stock fuel lines from the fuel tank to the engine bay with an upgraded -6an E85 compatible fuel line and adds an ethanol sensor and Bluetooth analyzer to monitor your ethanol content. Includes both Bluetooth App & 5v analog output for JB4 or flash tuning. For your fuel line upgrade, choose the option that supports your current configuration. HPFP to the fuel tank: (Stock) This upgrade replaces both stock fuel lines with one upgraded continuous fuel line from the fuel tank to the HPFP and adds the ethanol sensor. Port Injection to the fuel tank: If you are running our port injection kit, this upgrade replaces the stock fuel lines from the tank to the engine bay, integrates the ethanol sensor and then utilizes a Y adapter to supply the HPFP and PI with fuel. Our custom fittings remove those tee's and extra fittings for a cleaner high flow setup. Non-Fuel-It! port injection to fuel tank: Choose this option if you are running a port injection kit that we did not manufacture or sell. This kit includes a longer 18" feedline from the Y to the port injection rail. You then cut the feed line to the length you need and install the included -6an female fitting or -6an female elbow to make the connection to your port injection rail. All of these kits utilize the BMS custom billet aluminum fittings to integrate with the stock fittings so no modifications are needed. *For the BMW N54 E-series JB4 platform connect the white wire to position #15 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *For the BMW N55 E-series JB4 platform connect the white wire to position #16 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Fuel-It! Flex Fuel Kit - N54/N55 5 Series

T#:21242701

Part#: FFK-N5XB

In Stock

Sale - Save 4% $ 485.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 464.99 USD

Add to Wish List

Sale - Save 4%

$ 485.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 464.99 USD

Add to Wish List

This is a complete plug and play kit to install a Bluetooth ethanol sensor in your E-Series BMW. (Check compatibility for your platform below) This kit replaces the stock fuel lines from the fuel tank to the engine bay with an upgrade -6an E85 compatible fuel line and adds an ethanol sensor and Bluetooth analyzer to monitor your ethanol content. This kit features a 0-5 volt analog output that integrates with the JB4, analog gauge, or any other ECU or tuner that supports 0-5 volt input. All of these kits utilize a custom billet aluminum fittings to integrate with the stock fittings so no modifications are needed. For your fuel line upgrade, choose the option that supports your current configuration. HPFP to the fuel tank: (Stock) This upgrade replaces both stock fuel lines with one upgraded continuous fuel line from the fuel tank to the HPFP and adds the ethanol sensor. Port Injection to the fuel tank: If you are running our port injection kit, this upgrade replaces the stock fuel lines from the tank to the engine bay, integrates the ethanol sensor and then utilizes a Y adapter to supply the HPFP and PI with fuel. Our custom fittings remove those tee's and extra fittings for a cleaner high flow setup. Non-Fuel-It! port injection to fuel tank: Choose this option if you are running a port injection kit that we did not manufacture or sell. This kit includes a longer 18" feedline from the Y to the port injection rail. You then cut the feed line to the length you need and install the included -6an female fitting or -6an female elbow to make the connection to your port injection rail. *These kits are available for off-road use only *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated. *For the BMW N54 E-series JB4 platform connect the white wire to position #15 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *For the BMW N55 E-series JB4 platform connect the white wire to position #16 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Fuel-It! Flex Fuel Kit - N20/N26 F Chassis

T#:21275574

Part#: FFK-N20/6F-FK

In Stock

$ 369.99

This product was last offered at the strikethrough price on
07-27-2026

$ 353.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 369.99

This product was last offered at the strikethrough price on
07-27-2026

$ 353.99 USD

Limited Qty Sale

Add to Wish List

This is a complete plug and play kit to install a Bluetooth ethanol sensor in about 30 minutes! The kit includes the following: New 5/16" E85 compatible fuel lines for your engine bay Genuine Continental ethanol sensor Fuel-It! Bluetooth analyzer Plug and play harness Includes both Bluetooth App & 5v analog output for JB4 or flash tuning NOTICE: If you have an N26 motor type, you will need to retrofit the HPFP supply line to part number 13537585415 to be compatible with this kit. *For the BMW F-series JB4 platform connect the white wire to position #14 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 14/15/16 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Fuel-It! Elite Port Injection Kit With 950cc Injectors & Fuel Line ...

T#:26038542

Part#: BMW-EPI-950

Ships on Aug 31, 2026

$ 1,188.00 USD

Add to Wish List

Qty

$ 1,188.00 USD

Add to Wish List

This kit is designed to enhance performance by adding six supplemental low-pressure fuel injectors, capable of supporting 1000+ WHP on E85 and similar high-performance fuels.

Crafted with precision, the manifold spacers are CNC machined and anodized to ensure durability and prolonged service life. Each kit comes complete with all necessary installation hardware, a gasket set, and a plug-and-play fuel line adapter for seamless integration.

The Elite kit stands out with its sleek black anodized finish and includes an additional return port, an upgraded fuel line, and enhanced machining to accommodate a wider range of applications, including the BMW S55 engine.

A port injection controller is not included. This is required for a complete installation.

Show More Show Less

E89 Silent Fan EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471534

Part#: SILENT-E89-EKP

Ships in 1 Business Day

Starting at $ 59.99 USD

Add to Wish List

Starting at $ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E82 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8, which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put it into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket in order to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable ASA, ABS or PETG, depending on the color choice. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With a Genuine 60mm or 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a silent Noctua fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

BMW Port Injection Kit - B58 2015+

T#:38890887

Part#: BMS-PIK-B58

Ships on Aug 31, 2026

$ 699.00 USD

Add to Wish List

Qty

$ 699.00 USD

Add to Wish List

The Fuel-It! Port Injection Manifold Spacers are precisely CNC-machined for a seamless, factory-like fit and anodized black for enhanced durability and a sleek appearance. This port injection kit includes all necessary installation hardware, heavy-duty gaskets, and a plug-and-play BMS braided fuel line adapter. To complete the kit, you'll need the Fuel Line, Fuel Injectors, and a Port Injection Controller, which are available separately or can be added to your package. An aftermarket charge pipe is required to accommodate the additional height of the manifold. For Gen 1 B58, we recommend the BMS Elite Aluminum Replacement Charge Pipe Upgrade, while for Gen 2 B58, options include the BMS Elite BMW/Supra B58TU Gen2 Charge Pipe Blow-Off Valve (BOV) Kit or the BMS Elite BMW/Supra B58TU Gen2 Charge Pipe.

Show More Show Less

Fuel-It! Flex Fuel Kit - F-Chassis S55 - BMS/FI PI

T#:21275563

Part#: FFK-S55-FIP

Ships on Aug 31, 2026

$ 589.99 USD

Add to Wish List

Qty

$ 589.99 USD

Add to Wish List

If you are running E85 or ethanol mixes in your BMW, you need this kit! This is a complete plug and play kit to install a Bluetooth ethanol sensor in your S55 BMW. This kit replaces the stock fuel lines from the fuel tank to the engine bay with an upgraded -6an E85 compatible fuel line and adds an ethanol sensor and Bluetooth analyzer to monitor your ethanol content. Includes both Bluetooth App & 5v analog output for JB4 or flash tuning. For your fuel line upgrade, choose the option that supports your current configuration. HPFP to the fuel tank: (Stock) This upgrade replaces both stock fuel lines with one upgraded continuous fuel line from the fuel tank to the HPFP and adds the ethanol sensor. Port Injection to the fuel tank: If you are running our port injection kit, this upgrade replaces the stock fuel lines from the tank to the engine bay, integrates the ethanol sensor and then utilizes a Y adapter to supply the HPFP and PI with fuel. Our custom fittings remove those tee's and extra fittings for a cleaner high flow setup. Non-Fuel-It! port injection to fuel tank: Choose this option if you are running a port injection kit that we did not manufacture or sell. This kit includes a longer 18" feedline from the Y to the port injection rail. You then cut the feed line to the length you need and install the included -6an female fitting or -6an female elbow to make the connection to your port injection rail. All of these kits utilize the BMS custom billet aluminum fittings to integrate with the stock fittings so no modifications are needed. *For the BMW F-series JB4 platform connect the white wire to position #16 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *These kits are available for off-road use only *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

E-Chassis Stage 3 Bucketless LPFP Upgrade - N54/55

T#:38890918

Part#: BMSS3BLPFPN5455

Ships on Aug 31, 2026

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

If you're already using our Stage 2 Bucketless LPFP and want to upgrade to Stage 3, this kit is for you. If you don’t have the Stage 2 kit, you can purchase it here. Note: Stage 3 requires the Stage 2 bucketless kit. The Stage 3 upgrade kit includes: - Complete plug-and-play solution with the addition of the secondary module - Custom billet aluminum fitting to run both pumps in parallel - Wiring harness for the secondary pump - Spare vent tube clip - New Walbro filter - New E85-compatible Walbro 450 pump (F90000274) - Optional upgrade to Walbro 525 pump (F90000285) Recommended accessories: - Lock Ring Removal Tool - Hobb's switch

Show More Show Less

Fuel-It! Flex Fuel Kit - B58 G05

T#:21275576

Part#: FFK-B58X-FK

Ships on Aug 31, 2026

$ 349.99 USD

Add to Wish List

Qty

$ 349.99 USD

Add to Wish List

Know your exact ethanol content in real-time via the Fuel-It! or JB4 mobile app on your smartphone or tablet. The complete kit includes the following: Genuine Continental ethanol sensor Fuel-It! Bluetooth Universal Analyzer One stainless steel braided fuel line with black nylon sheathing to protect your other engine bay components Proprietary custom billet fitting for plug and play OEM integration One custom wiring harness 1 tube of SuperLube® for hose adapter install Bluetooth Model Supports stand-alone Bluetooth operation with the Fuel-It! app *For the G-series JB4 platform connect the white wire to position #4 on the JB4 25 pin harness. Select WMI Ethanol Setup option 0 to enable pin location 2/3/4 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Fuel-It! Bluetooth Flex Fuel Kit - B46/B48/B58

T#:21209854

Part#: FFK-B464858

Ships on Aug 28, 2026

Starting at $ 479.99 USD

Add to Wish List

Starting at $ 479.99 USD

Add to Wish List

If you're running E85 or ethanol mixes in your BMW, you need this kit! As many of you know the BMW motors can be very picky about how much ethanol you run to achieve peak performance but not run lean. Consequently, BMS have put together a kit enabling you to easily install an ethanol sensor with no permanent modifications needed. You will simply remove your low pressure fuel line in the engine bay and plug in our kit. It's a complete plug and play solution that utilizes our Bluetooth app to monitor your ethanol content. When you are ready to return to stock, you will simply remove the kit and re-install the stock fuel line. The complete kit includes the following: Genuine Continental ethanol sensor Fuel-It! Bluetooth Universal Analyzer Two stainless steel braided fuel lines with black nylon sheathing to protect your other engine bay components Proprietary custom billet fittings for plug and play OEM integration One wiring harness with Posi-tap connector Bluetooth Model Supports stand-alone Bluetooth operation with the Fuel-It! app *For the JB4 platform connect the white wire to position #4 on the JB4 25 pin harness. Select WMI Ethanol Setup option 0 to enable pin location 2/3/4 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Port Injection Kit

T#:25839000

Part#: BMW-N54-PRM-750

Ships on Aug 31, 2026

$ 988.00 USD

Add to Wish List

Qty

$ 988.00 USD

Add to Wish List

A90 MKV B58 Supra Fuel-It! Flex Fuel Kit

T#:21275577

Part#: FFK-B58S-FK

Ships on Aug 31, 2026

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

A90 MKV B58 Supra Fuel-It! Flex Fuel Kit is the ultimate upgrade for monitoring and managing your Toyota Supra’s ethanol content in real-time. This complete kit, offered by Turner Motorsport, allows you to know your exact ethanol content through the Fuel-It! or JB4 mobile app on your smartphone or tablet. It’s perfect for those looking to maximize performance by running ethanol blends, providing you with precise data to make informed decisions.

This kit includes everything you need for installation, featuring a genuine Continental® ethanol sensor, stainless steel braided fuel lines with black nylon sheathing, a Fuel-It! Bluetooth analyzer, and a plug-and-play harness. It also supports both Bluetooth App and 5v analog output for JB4 or flash tuning.

Real-Time Monitoring: Instantly view ethanol content on your smartphone or tablet via the Fuel-It! or JB4 app.
Comprehensive Kit: Includes a genuine Continental® ethanol sensor, Fuel-It! Bluetooth analyzer, and more.
Durable Construction: Stainless steel braided fuel lines with black nylon sheathing protect engine bay components.
Plug-and-Play Installation: Simplified installation with a plug-and-play harness.
Bluetooth and Analog Output: Supports both Bluetooth connectivity and 5v analog output for JB4 or flash tuning.
Optimized Performance: Perfect for those looking to maximize power by running ethanol blends.

Show More Show Less

Fuel-It! Flex Fuel Kit - F-Chassis S55 - Non BMS/FI PI

T#:21275564

Part#: FFK-S55-NFI

Ships on Aug 31, 2026

$ 609.99 USD

Add to Wish List

Qty

$ 609.99 USD

Add to Wish List

If you are running E85 or ethanol mixes in your BMW, you need this kit! This is a complete plug and play kit to install a Bluetooth ethanol sensor in your S55 BMW. This kit replaces the stock fuel lines from the fuel tank to the engine bay with an upgraded -6an E85 compatible fuel line and adds an ethanol sensor and Bluetooth analyzer to monitor your ethanol content. Includes both Bluetooth App & 5v analog output for JB4 or flash tuning. For your fuel line upgrade, choose the option that supports your current configuration. HPFP to the fuel tank: (Stock) This upgrade replaces both stock fuel lines with one upgraded continuous fuel line from the fuel tank to the HPFP and adds the ethanol sensor. Port Injection to the fuel tank: If you are running our port injection kit, this upgrade replaces the stock fuel lines from the tank to the engine bay, integrates the ethanol sensor and then utilizes a Y adapter to supply the HPFP and PI with fuel. Our custom fittings remove those tee's and extra fittings for a cleaner high flow setup. Non-Fuel-It! port injection to fuel tank: Choose this option if you are running a port injection kit that we did not manufacture or sell. This kit includes a longer 18" feedline from the Y to the port injection rail. You then cut the feed line to the length you need and install the included -6an female fitting or -6an female elbow to make the connection to your port injection rail. All of these kits utilize the BMS custom billet aluminum fittings to integrate with the stock fittings so no modifications are needed. *For the BMW F-series JB4 platform connect the white wire to position #16 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *These kits are available for off-road use only *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Radium - Split-Flow Flex Fuel Sensor Adapter

T#:53290958

Part#: 20-0589

In Stock at Vendor

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

Fuel-It! Flex Fuel Kit - G2x/G3x/G4x B58

T#:21209864

Part#: GB58BFFK

Ships on Aug 31, 2026

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

The complete kit with Bluetooth ECA includes the following: Genuine Continental® ethanol sensor Two stainless steel braided fuel lines with black nylon sheathing to protect your other engine bay components Fuel-It! Bluetooth analyzer (iPhone or Android app must be downloaded to use this kit) Plug and play harness Includes both Bluetooth App & 5v analog output for JB4 or flash tuning *For the BMW G-series JB4 platform connect the white wire to position #4 on the JB4 25 pin harness. Select WMI Ethanol Setup option 0 to enable pin location 2/3/4 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Fuel-It! Bluetooth FLEX FUEL KIT For The S63TU 2012-2016 F10 BMW M5 &...

T#:16840517

Part#: FFKS63TUFXM

Ships on Aug 31, 2026

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

Know your exact ethanol content in real-time via the Fuel-it! or JB4 app on your smartphone or tablet. The kit includes the following: Genuine Continental® ethanol sensor Two stainless steel braided fuel lines with black nylon sheathing to protect your other engine bay components Proprietary custom billet fittings for plug and play OEM integration Fuel-It! Bluetooth analyzer (iPhone or Android app must be purchased to use this kit) Plug and play harness Includes both Bluetooth App & 5v analog output for JB4 or flash tuning Bluetooth (iPhone or Android app must be downloaded to use this feature) *For the BMW F-series JB4 platform connect the white wire to position #16 on the JB4 25 pin harness. Select WMI page bit 1 to enable. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

E89 EKP PNP Cooler Kit - (Z4)

A Must For Cars With Upgraded LPFPs

T#:26471566

Part#: E89-EKP-PNP

Ships in 1 Business Day

Starting at $ 44.99 USD

Add to Wish List

Starting at $ 44.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E89 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8, which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put it into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+ or PETG, depending on the color choice. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

Fuel-It! Flex Fuel Kit - B58 G29 Z4

T#:21275568

Part#: FFK-G29Z4-CK

Ships on Aug 31, 2026

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

If you are running E85 or ethanol mixes in your BMW, you need this kit! This is a complete plug and play kit to install a Bluetooth ethanol sensor in your B58 powered G29 Z4. This kit replaces the stock fuel lines from the fuel tank to the engine bay with an upgraded -6an E85 compatible fuel line and adds an ethanol sensor and Bluetooth analyzer to monitor your ethanol content. Includes both Bluetooth App & 5v analog output for JB4 or flash tuning. All of these kits utilize the BMS custom billet aluminum fittings to integrate with the stock fittings so no modifications are needed. For the G29 Z4 JB4 platform connect the white wire to position #4 on the JB4 25 pin harness. Select WMI Ethanol Setup option 0 to enable pin location 2/3/4 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Fuel-It! B58 BMW High Pressure Fuel Pump (HPFP) Upgrade - Stage 2 ...

T#:13003684

Part#: BMWB58HPFPSTG2

Ships on Aug 31, 2026

$ 1,499.00 USD

Add to Wish List

Qty

$ 1,499.00 USD

Add to Wish List

Introducing the new B58 BMW HPFP upgrade kit from Fuel-It! Replaces your factory high-pressure fuel pump with a higher capacity pump capable of supporting 30% more flow with Stage1 or 60% more flow with Stage2! Includes all required installation hardware for a clean plug and play install. Includes: Upgraded High-Pressure Fuel Pump (HPFP) Billet Adapter Plate Billet Center Alignment Tool Low-pressure Line (Triple lined crimped fittings PTFE/SS/Nylon Braided) Custom Harness and Hardware

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results