This product was last offered at the strikethrough price on
09-04-2026
Looking to stiffen up your rear shock mount without going for a solid rear mount? The Polyurethane Rear Performance Strut Mount from IRP will give you the stiffer reinforcement without giving you the typical noise, vibration, and harshness that come with traditional performance strut mounts. The polyurethane also helps with preventing rear shock blowouts, a common problem for stock BMW rear mounts that are paired with stiffer than stock suspension.
The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.
Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels
This product was last offered at the strikethrough price on
05-07-2026
This product was last offered at the strikethrough price on
09-04-2026
This product was last offered at the strikethrough price on
05-07-2026
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
Due to their soft rubber construction, OE strut mounts are known to wear at an accelerated rate. Many high-mileage vehicles fall victim to strut mount failure, which is commonly associated with annoying clunks, groans, or rattles from the front suspension.
With this issue in mind, ECS Tuning developed their heavy-duty front strut mount with upgraded, higher durometer rubber to resolve sloppy handling and increase longevity. Manufactured precisely within OEM tolerances, these mounts are a perfect fit for your BMW.
Features:
Reduces deflection: Increases vehicle handling and cornering dynamics by removing deflection within the strut mount. Increases longevity: Upgraded rubber construction makes for a stiffer mount, less prone to cracking and general degradation. Developed in-house: Designed and tested by ECS Tuning engineers, this mount is sure to outlast an OE replacement. Upgrade to a better strut mount without sacrificing ride comfort! Improve longevity and ride control all at once.
This product was last offered at the strikethrough price on
05-07-2026
This product was last offered at the strikethrough price on
05-02-2026
This product was last offered at the strikethrough price on
05-02-2026
This product was last offered at the strikethrough price on
05-07-2026
This product was last offered at the strikethrough price on
05-07-2026
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
Want a race-spec rear shock mount but with the comfort of a factory bushing? This ECS rear shock mount combines the precision and articulation of a spherical bearing with the isolation of urethane bushings. The stainless monoball bearing is lined with PTFE lubricant and suspended in 80A urethane and housed in a hard anodized 6061-T6 aluminum mount. The spherical bearing is a better design than most rear shock mounts because it allows the shock to move and tilt without side-loading the shock shaft (which leads to premature failure of the shock). Most Genuine BMW and aftermarket shock mounts are not designed for shock angles and the stress that track or performance driving will put on the shock shaft. The ECS shock mount is properly designed to handle these loads. The internal bearing is also replaceable - it will be years before you have to replace the entire mount. The ECS mount is fully encapsulated to prevent the common shock mount failure of the stock mount design.
ECS RSM features:
* - the RSM comes with the BMW standard 10mm shock shaft bushings. 12mm is used on some performance shocks and 14mm is used on some true motorsport rear shocks.
Want the best performance option in shock tower mounts? IRP has created their pillow-ball rear shock mounts for just this need. These rear shock mounts are designed for use on the track and racing. This set of mounts will help your rear shocks perform the best they can in all conditions. The advantage to using a mount with spherical bearing is that it allows the shock to freely move off axis without side loading the shock shaft like rubber or polyurethane mounts do. Side loading a shock increases stiction and wear which decreases its efficiency. Because these are mounts without an isolator (rubber or polyurethane) to dampen road noise and vibrations we do not recommend them for street cars.
The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.
Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels
This product was last offered at the strikethrough price on
05-29-2026
