This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
The E36/E46 rear trailing arm bushings (RTABs) wear out faster than any other bushing on the car. Worn RTAB will cause excessive toe alignment change and give a 'loose' or 'floaty' feeling in the rear handling. One of the reasons for this is that they over-extend during motion, stretching and twisting the rubber in all directions. These shims sit on either side of the bushing and limit the amount of extension from the bushing. Not only will you get more life from your RTAB but these will help stiffen the bushing during cornering. But during normal driving you will still have all of the comfort of the stock rubber bushings. These part about these bushings is how easy they are to install - simply slide them in place during your bushing install. They can be added to pre-installed bushings too by dropping the trailing arm and removing the cage around the bushing.
Works with stock rubber bushings only (not urethane or Delrin).
Optimize rear suspension geometry with Whiteline suspension bushings. Often overlooked, Whiteline trailing arm bushings offer superior dynamic alignment precision by controlling excessive movement - providing driver reassurance for more predictable handling.
Features:
These bushings replace the stock rubber bushings and offer a better driving feel, increased lifespan, and better wheel alignment.
Rubber bushing allow for a lot more movement and are more susceptible to wear and tear from spirited driving and harsh weather conditions. Polyurethane is much more resistant to wear and is stiffer, reducing the total amount of movement that would normally affect the alignment negatively.
Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.
Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3
Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36
Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty
These bushings replace the stock rubber bushings and offer a better driving feel, increased lifespan, and better wheel alignment.
Rubber bushing allow for a lot more movement and are more susceptible to wear and tear from spirited driving and harsh weather conditions. Polyurethane is much more resistant to wear and is stiffer, reducing the total amount of movement that would normally affect the alignment negatively.
These bushings replace the stock rubber bushings and offer a better driving feel, increased lifespan, and better wheel alignment.
Rubber bushing allow for a lot more movement and are more susceptible to wear and tear from spirited driving and harsh weather conditions. Polyurethane is much more resistant to wear and is stiffer, reducing the total amount of movement that would normally affect the alignment negatively.
Swapping in E46 control arms into your E30 or E36 will significantly increase negative camber by widening the track width and will also give you more clearance for more steering angle. Condor's conversion bushings are machined from UHMW due to its high rigidity and low coefficient of friction allowing for minimal suspension bushing deflection (geometry change). They've designed them offset to re-center the wheel and give your e30/e36 the correct caster. They will include a stainless-steel insert that tightly presses over the hex pattern on the E46 control arms. You do not need to grind down your control arms or make any other modifications to your chassis. Please note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36.
Fitment:
Fits the following Meyle and Lemforder arms with 21-22MM Hex.
LEMFORDER ZHP - 31122282121 & 31122282122
LEMFORDER - 31126777851 & 31126777852
MEYLE HD - 31126777851 & 31126777852
*Please note that Meyle makes a standard e46 control arm and a Heavy Duty control arm. SOME HD arms have a hex that is larger in size. These HD control arms may need to be shaved 1-2 mm for proper fitment.
This product was last offered at the strikethrough price on
08-13-2026
This product was last offered at the strikethrough price on
10-01-2026
These bushings replace the stock rubber bushings and offer a better driving feel, increased lifespan, and better wheel alignment.
Rubber bushing allow for a lot more movement and are more susceptible to wear and tear from spirited driving and harsh weather conditions. Polyurethane is much more resistant to wear and is stiffer, reducing the total amount of movement that would normally affect the alignment negatively.
This product was last offered at the strikethrough price on
10-01-2026
This product was last offered at the strikethrough price on
10-01-2026
This product was last offered at the strikethrough price on
10-01-2026
Experience effortless caster adjustment with KMAC's premium inner thrust arm bushings.
Key Features:
1. Patented Design: Enjoy precise adjustments with a single wrench, even under load directly on the alignment rack.
2. Simplified Adjustment: Say goodbye to inaccurate multi-bolt systems and time-consuming disassembly for readjustments.
3. Extensive Adjustment Range: Benefit from the largest and strongest adjustment range available.
4. Mono Ball/Dual-Axis Bushings
5. Enhance brake and steering response with these high-performance bushings.
6. Superior Design: Our unique design surpasses traditional steel spherical bearings, offering over 2 ½ times the load-bearing and impact area.
Upgrade your vehicle's handling and responsiveness with KMAC's innovative inner thrust arm bushings.
