This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
Stock rear lower control arms offer very little adjustment for alignment, especially in lowered vehicles, due to their use of an eccentric bolt. These aftermarket performance control arms from ECS Tuning are designed for maximum adjustability, allowing you to maximize handling and minimize tire wear.
To ensure maximum reliability, ECS Tuning's control arms are constructed from strong, lightweight 6061-T6 aluminum and feature a 303 stainless steel center turnbuckle that offers over 8 degrees of fast and precise camber adjustment. The inner bushing is a stock style serviceable OEM bushing for long life and inexpensive maintenance.
Features:
Durable construction suitable for the daily driver and track car alike
8+ degrees adjustment range for dialing in any suspension and wheel/tire setup
Center located adjuster for maximum clearance during adjustment
OEM-style bushing for long life and inexpensive service
Black anodized 6061-T6 aluminum with 303 stainless steel turnbuckle
Includes new hardware
*With the exception of the stance community, most enthusiasts will need no more than a few degrees of adjustment range. Total adjustment often is dependent on wheel/tire clearances.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
The rear lower control arms on E82/E9X models are the weakest link in the rear suspension. The arm is made from folded sheetmetal and it bends and deforms easily. Not only will it deform from potholes and curbs, tow truck drivers love to hook onto them without realizing how weak they are. We have seen other race teams complete the box section to make them stronger. A bent arm will throw off the geometry in the suspension, potentially affecting handling and tire wear. These aluminum arms are both lighter and stronger than the factory sheetmetal arms and is the best solution for chronic bending of the stock arm. These are a direct replacement to your stock arms with no changes needed to your alignment. New high-grade hardware is included.
Note: the stock arm is designed from the factory to be intentionally weak. These arms will bend so that something else in the suspension does not break. Our race cars used the stock sheetmetal arm but we replaced them often. We found that it was better to finish a race with a bent arm than not finish due to a catastrophic failure. The ECS arms are still designed to be the weakest link but are far stronger than the factory arm and will not bend as easily.
This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi M3 - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
The E36/E46 rear trailing arm bushings (RTABs) wear out faster than any other bushing on the car. Worn RTAB will cause excessive toe alignment change and give a 'loose' or 'floaty' feeling in the rear handling. One of the reasons for this is that they over-extend during motion, stretching and twisting the rubber in all directions. These shims sit on either side of the bushing and limit the amount of extension from the bushing. Not only will you get more life from your RTAB but these will help stiffen the bushing during cornering. But during normal driving you will still have all of the comfort of the stock rubber bushings. These part about these bushings is how easy they are to install - simply slide them in place during your bushing install. They can be added to pre-installed bushings too by dropping the trailing arm and removing the cage around the bushing.
Works with stock rubber bushings only (not urethane or Delrin).
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
This product was last offered at the strikethrough price on
05-02-2026
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
This product was last offered at the strikethrough price on
05-02-2026
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
Control arms are some of the most crucial components on a BMW suspension. The control arms literally control the wheel and suspension as they go through their range of motions. A faulty or worn control arm or ball joint is a very dangerous and potentially life-threatening problem so make sure they are inspected and replaced at regular intervals. For a street-driven car we advise yearly inspection and a full replacement every 3-4 years. For track-driven cars these should be inspected before every event and replaced every two years.
OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.
As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!
This item fits the following BMW Chassis:
F25 X3,F26 X4
