Steering Angle Kits

Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 65 degrees.

This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.

Kit features:

• CNC Laser Cut Components
• Plug & Play - includes all needed hardware
• Increase to 65 Degree (or more) steering angle
• Includes Camber Plates
• Stiffer offset control arm bushings
• Roll Center and Bump Steer Correction Plates
• High strength control arms with steel monoball ball joints
• Increased length steering tie rods with steel monoball ball joints
• DriftAllstar- & EEDC-Tested
• Total weight of all components included: 13.5 kg / 29.8 lbs

Fits the following BMWs:
1999-2006 E46 BMW M3

ECS Tuning Steering Rack Spacers – A Simple Upgrade for More Angle

Whether you're just beginning your drift journey or looking to refine your current angle kit, ECS Tuning's Steering Rack Spacers offer a simple yet effective solution. Installation is straightforward—just remove the inner tie rods and place the spacers with the chamfered side facing the tie rod for an instant angle boost.

During the development of their ECS E90 drift build, the team at ECS Tuning was eager to hit the track and start testing. On the first day of driving, it quickly became apparent that two essential upgrades were needed: a welded differential (which led to the creation of their custom-fit differential plates – (T#:35121162) and increased steering angle. However, rather than jumping straight into a full-angle kit, ECS focused on incremental improvements to fine-tune the car’s handling.

ECS engineers, including a beginner drifter, carefully measured and tested different spacer sizes to optimize angle while maintaining proper thread engagement on the inner tie rod. After extensive testing, they determined that 5mm was the sweet spot—providing the extra angle needed while ensuring a strong and secure connection.

For those looking to enhance their drift setup without committing to an expensive angle kit, ECS Steering Rack Spacers offer an affordable and effective solution.

Key Benefits:

Gain approximately 5° of extra steering angle on an otherwise stock setup
Budget-friendly alternative to expensive angle kits
Simple, bolt-on installation—no major modifications required
Works as a standalone mod or can be paired with angle kits for even greater gains
Design & Materials:

Material: Mild Steel
Finish: Zinc Coated for durability
Size: 5mm spacers
Take your drifting to the next level—one small upgrade at a time with ECS Tuning’s Steering Rack Spacers!

Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 65 degrees.

This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.

Kit features:

• CNC Laser Cut Components
• Plug & Play - includes all needed hardware
• Increase to 65 Degree (or more) steering angle
• Includes Camber Plates
• Stiffer offset control arm bushings
• Roll Center and Bump Steer Correction Plates
• High strength control arms with steel monoball ball joints
• Increased length steering tie rods with steel monoball ball joints
• DriftAllstar- & EEDC-Tested
• Total weight of all components included: 13.5 kg / 29.8 lbs

Fits the following BMWs:
1982-1991 E30 BMW All RWD Submodels

Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock, are a chromolon tubular system, and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 70 degrees.

This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.

*This Pro kit offers reduced weight control arms that help this kit shed 2.9 lbs from the standard kit while still remaining just as strong thanks to their chromolon tubular design.*

Kit features:

• CNC Laser Cut Components
• Plug & Play - includes all needed hardware
• Increase to 70 Degree (or more) steering angle (5 degrees more than standard version)
• Includes Camber Plates
• Stiffer offset control arm bushings
• Roll Center and Bump Steer Correction Plates
• High Strength chromolon tubular control arms with steel monoball ball joints (2cm wider than standard version)
• Increased length steering tie rods with steel monoball ball joints
• DriftAllstar- & EEDC-Tested
• Total weight of all components included: 12.2kg / 26.9lbs (1.3kg / 2.9lbs lighter that standard version)

Fits the following BMWs:
1999-2006 E46 BMW All RWD Submodels