BMW Internal Engine Parts

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Ferrea Performance Intake Valve - Stock Size

T#:583445

Part#: F1550P

Back Ordered

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Timing Chain - Upper

T#:17871154

Part#: 11311432177

In Stock

Sale - Save 20% $ 27.99

This product was last offered at the strikethrough price on
05-03-2026

$ 22.39 USD

Add to Wish List

Qty

Sale - Save 20%

$ 27.99

This product was last offered at the strikethrough price on
05-03-2026

$ 22.39 USD

Add to Wish List

Ferrea Performance Exhaust Valve - Stock Size

T#:583444

Part#: F1552P

Ships on Sep 2, 2026

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Replacement Piston Ring Set For Turner Motorsport/Wiseco E30 M3 2.5-l...

T#:26538305

Part#: 9400XX

In Stock

$ 31.99

This product was last offered at the strikethrough price on
05-03-2026

$ 30.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 31.99

This product was last offered at the strikethrough price on
05-03-2026

$ 30.99 USD

Limited Qty Sale

Add to Wish List

Crankshaft Position Sensor

T#:13793006

Part#: 13627809334

Ships in 4 Business Days

$ 81.99

This product was last offered at the strikethrough price on
05-07-2026

$ 79.99 USD

Add to Wish List

Qty

$ 79.99 USD

Add to Wish List

Timing Component

T#:17871158

Part#: 11367583208

In Stock

Sale - Save 20% $ 199.99

This product was last offered at the strikethrough price on
05-03-2026

$ 159.99 USD

Add to Wish List

Qty

Sale - Save 20%

$ 199.99

This product was last offered at the strikethrough price on
05-03-2026

$ 159.99 USD

Add to Wish List

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Forged Piston & Ring Set - 77mm - (Set of 4)

T#:22756709

Part#: K618M77

In Stock

$ 696.99 USD

Add to Wish List

Qty

$ 696.99 USD

Add to Wish List

When it comes to engine builds, whether you're planning a high-boost monster or a straightforward rebuild, the strength of your build is only as good as its weakest link. In this context, piston rings play a crucial role. They are not to be underestimated, as they can make or break your engine's performance and oil consumption.

Wiseco, a renowned and trusted name in the engine building world, has earned its reputation through consistent product performance. Their piston rings are no exception and are a valuable addition to your engine building puzzle.

Key Features:

Wiseco piston rings ensure optimal engine performance.
Trusted and respected brand in the engine building industry.
Compatible with a variety of engine builds.
8.5:1 compression ratio for enhanced power and efficiency.

Show More Show Less

MINI W11 1.6L Forged Piston & Ring Set (Set of 4) - 77.5mm

T#:31158729

Part#: 618M775

In Stock at Vendor

$ 696.99 USD

Add to Wish List

Qty

$ 696.99 USD

Add to Wish List

MINI W11 1.6L Forged Piston & Ring Set (Set of 4) - 77.5mm is perfect for those planning a high-performance build with significant boost or compression, as well as for simple engine rebuilds. These pistons and rings ensure your engine operates at full potential without oil consumption issues.

Ideal for high-performance builds and simple rebuilds
Enhances engine strength and durability
Trusted Wiseco brand ensures reliable performance
8.5:1 compression ratio for improved performance
Reduces the risk of oil consumption

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - N54

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Wiseco BMW Turbo 84.50MM Bore +0.50 Oversized 8.8:1 CR Pistons ...

T#:4319885

Part#: WISKE115M845

In Stock at Vendor

$ 1,157.99 USD

Add to Wish List

Qty

$ 1,157.99 USD

Add to Wish List

Includes piston rings and wrist pins.

Spline Lock Crank Hub Solution

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Hella Crankshaft Bearing Set - Standard Size - 55.0mm

T#:27638781

Part#: 11210666100

In Stock at Vendor

$ 143.99

This product was last offered at the strikethrough price on
05-07-2026

$ 141.99 USD

Add to Wish List

Qty

$ 141.99 USD

Add to Wish List

Often called main bearings, crankshaft bearing shells sit between the rotating assembly and the engine block. They allow the crankshaft to rotate freely, but are prone to wear from deterioration and lack of lubrication.

This complete set consists of nine bearings, enough to fill each journal.

If you're overhauling your M10, choose Hella crankshaft-bearing shells for a lasting solution.

Show More Show Less

Wiseco BMW Piston - set

T#:640415

Part#: KE119M845

In Stock at Vendor

$ 1,157.99 USD

Add to Wish List

Qty

$ 1,157.99 USD

Add to Wish List

Wiseco BMW M52B28 2.8L 24V Turbo 84.5mm Bore +.50 Oversized 8.0:1 CR Pistons For M52

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

T#:19395579

Part#: VTTCRANKHUBPKG

Ships in 10 Business Days

$ 934.99 USD

Add to Wish List

Qty

$ 934.99 USD

Add to Wish List

VTT is proud to offer the only complete N54 complete crank hub solution that does NOT require the crank to be drilled for pins. Our hub uses our proprietary “Spline Lock” technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). We spent many months testing, and retesting this design, utilizing well over 10 different samples to come to our final production version. During testing, our final hub managed to break our testing rig before slipping. These have been bench tested, and real-world tested on the VTT N54 race car spinning 8K RPM and making well over 900WHP. This technology means our hub installs the same as a stock hub, no drilling of the crank, which means MUCH less labor is involved and is reversible is ever wanting to be uninstalled leaving no holes in the crank. The “Spline Lock” is ONLY available with the VTT Crank bolt capture for the ULTIMATE Crank Hub solution for your BMW. These parts are designed to be used together, and the spline lock should not run without the CBC VTT “Spline Lock” Crank hubs are CNC manufactured from 440C tool Steel with a Rockwell rating of HRC60 for the ultimate in durability, and toughness. Hub Plus OEM bolt OEM Oil pump sprocket OEM oil sprocket retainer VTT Crank bolt capture

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 5 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

T#:439

Part#: S10049-24

Back Ordered

$ 817.20 USD

Add to Wish List

Qty

$ 817.20 USD

Add to Wish List

Ferrea valve springs are developed from high strength alloys, including premium grade chrome silicone steel These springs are manufactured with state-of-the-art equipment. Ferrea springs are heat-treated and stress-relieved, which dramatically increases the spring's life. Strict quality control procedures and cycle testing ensures consistency from batch to batch. Ferrea valve springs provide the stability needed for high lift, high rpm racing and street car engines. Kit includes a set of 24 springs. MUST be used with the Ferrea Spring Seat and Titanium Retainers. See links below.

https://www.turnermotorsport.com/e/p-163-e36-325-328-m3-ferrea-spring-seat-set/

https://www.turnermotorsport.com/e/p-31-e36-325-328-m3-ferrea-titanium-retainer-set/

This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i

Show More Show Less

BMW N52 N54 Collar Screw

T#:17871157

Part#: 11367524954

In Stock

Sale - Save 20% $ 5.99

This product was last offered at the strikethrough price on
05-03-2026

$ 4.79 USD

Add to Wish List

Qty

Sale - Save 20%

$ 5.99

This product was last offered at the strikethrough price on
05-03-2026

$ 4.79 USD

Add to Wish List

Holds the camshaft gear to the camshaft, measures M10X1X94.

Ferrea High Performance Valve Kit - B58

T#:29035336

Part#: FER-HPVK-B58-T28

Ships in 4 Business Days

$ 1,059.99 USD

Add to Wish List

Qty

$ 1,059.99 USD

Add to Wish List

The BMW B58 engine can significantly benefit from the high-performance Ferrea valve kit, featuring the renowned Ferrea Competition Plus Valves. Known as the industry’s most dependable extreme-duty valves, these valves are crafted using special aerospace-grade alloys, including the high tensile strength EV8-Z18. To ensure unparalleled quality, an exclusive two-step slow forging process is utilized, promoting optimal grain flow and minimizing material structure damage. Additionally, the valves undergo a rigorous 48-hour heat treatment and stress-relieving process, crucial for maintaining their molecular integrity. The final touch is the application of avionics-quality hard chrome and a specially hardened tip, ensuring exceptional durability and reliability.

Show More Show Less

Ferrea High Performance Valve Kit - B58

T#:29035337

Part#: FER-HPVK-B58-T29

Ships in 4 Business Days

$ 929.00 USD

Add to Wish List

Qty

$ 929.00 USD

Add to Wish List

The BMW B58 engine can significantly benefit from the high-performance Ferrea valve kit, featuring the renowned Ferrea Competition Plus Valves. Known as the industry’s most dependable extreme-duty valves, these valves are crafted using special aerospace-grade alloys, including the high tensile strength EV8-Z18. To ensure unparalleled quality, an exclusive two-step slow forging process is utilized, promoting optimal grain flow and minimizing material structure damage. Additionally, the valves undergo a rigorous 48-hour heat treatment and stress-relieving process, crucial for maintaining their molecular integrity. The final touch is the application of avionics-quality hard chrome and a specially hardened tip, ensuring exceptional durability and reliability.

Show More Show Less

M50B25 2.5L Engine 11:1 CR 84.5MM Bore Custom Pistons (Set Of 6) ...

T#:19858301

Part#: KE114M845AP

Special Order: No Guaranteed ETA

$ 1,000.99 USD

Add to Wish List

Qty

$ 1,000.99 USD

Add to Wish List

Wiseco Forged Piston & Ring - E30 M3 2.3 liter - 3.720 inch bore (94....

T#:2380

Part#: TEN300623S

Special Order: No Guaranteed ETA

$ 726.99 USD

Add to Wish List

Qty

$ 726.99 USD

Add to Wish List

Wiseco BMW E30 M3 Piston set - 3.720" bore. Wiseco leads the performance aftermarket by producing the highest quality forged pistons. Extreme racing conditions demand the strength and toughness that only forged pistons can offer. Compared to cast pistons, forgings are tougher and more durable and will stand up to the abuse that high-performance motorsport applications require. Each set comes with rings, wrist pins, and clips. Born over 80 years ago from the passion for racing, Wiseco is a world leader in manufacturing high-performance, forged pistons for the motorcycle, automotive, ATV, snowmobile, personal watercraft, and outboard marine markets. The Wiseco crew shares the same level of dedication to motorsports as their customers and are focused on continually refining the quality and practices it takes to exceed expectations. Engineered, forged, and machined on cutting-edge equipment in the U.S. at Wiseco’s Mentor, Ohio manufacturing facility, Wiseco pistons are the undisputed leader in quality and performance. Wiseco Performance Products, built for racers, by racers. Bore Diameter - 94.50 Compression Height - 32.00 Forging Type - Full Round Oil Ring Thickness2.8 Piston Material - 2618 Piston Pin Included - Yes Piston Pin Material - 9310 Piston Volume - -32.00 Product Series - European Product Types - Piston Kits Ringset Included - Yes Second Compression Ring Thickness - 1.2 Skirt Coating - Y Top Compression Ring Thickness - 1.0 Wrist Pin Diameter - 0.866 Wrist Pin Style - Floating This item fits the following BMWs: 1988-1991 E30 BMW M3 2.3 liter

Show More Show Less

Professional BMW M54B30 Piston Set Of 6 – 84.00 Mm Bore – 30.32 M...

T#:45210339

Part#: KE324M84

Back Ordered

$ 1,081.99 USD

Add to Wish List

Qty

$ 1,081.99 USD

Add to Wish List

Project Cars

SELECT YOUR BMW

Sub-Categories

Key Features:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results