A performance clutch kit will allow you to drive harder under increased power levels while making sure there is nothing lost to the drivetrain. If you track your vehicle or have raised the maximum horsepower through tuning or modification, chances are you will see increased benefit by installing a high performance aftermarket clutch.
The ultimate in a racing flywheel and clutch! This was developed for use in our E36 and E46 World Challenge Touring Cars. The combined weight of the clutch and flywheel is only 11lbs!!!
This multi-disc (2 or 3 disc setups) offer a minimal flywheel mass (enough to include a factory ring gear for the starter) and a small 5.5" clutch assembly rated to 500hp. By saving as much weight as possible less energy is used in simply spinning the flywheel/clutch assembly and that means a lot more power and torque is available at the drive wheels. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines and this is among the most advanced and lightest racing clutch kits available for your BMW race car.
The JB Ultra-Light Performance racing clutch is available in 2-disc or 3-disc setups. We used the 5.5"/140mm size in our Touring Cars but larger sizes are available too. This is a turn-key racing clutch and flywheel kit that you don't have to engineer or spec yourself. This is the same clutch setup we used when winning the 2003 and 2004 Touring Car Championships - the quality and performance is unquestionable. That series also employed standing starts at each race and this clutch setup performed flawlessly with nearly a full season of racing on them before needing a change.
multi-disc racing clutch with Performance racing pressure plate
JB Racing throw-out bearing with custom bobbin This is a true racing clutch and will not function as a street-able clutch at all. It behaves as an on/off switch with no slippage allowed. Extreme care must be used when driving on to trailers and around the paddock. But when driven correctly the life span of this clutch is amazing - we could get a full season of racing a 300hp M54 from this clutch setup including standing starts at every race! Replacement clutch components and flywheel rebuilding are available.
A properly adjusted clutch stop is required for use with this clutch kit.
This item fits the following BMWs: 1992-1999 E36 BMW 325i 325is 328i 328is M3 1999-2006 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed) 1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 2003-2005 E85 BMW Z4 2.5i (5-speed)
Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.
Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.
In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.
The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.
Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).
The JB flywheel includes ignition trigger wheel.
This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325e up to 5/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.
Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.
Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.
In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.
The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.
Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).
The JB flywheel includes ignition trigger wheel.
This flywheel replaces the stock original dual-mass flywheel and should only be used with the corresponding 'dual-mass' clutch kit. According to BMW the dual mass flywheel was installed in all 325/325e from 5/86 on but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.
Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.
Show More Show Less
The ultimate in a racing flywheel and clutch! This was developed for use in our E36 and E46 World Challenge Touring Cars. The combined weight of the clutch and flywheel is only 11lbs!!!
This multi-disc (2 or 3 disc setups) offer a minimal flywheel mass (enough to include a factory ring gear for the starter) and a small 5.5" clutch assembly rated to 500ft-lbs. By saving as much weight as possible less energy is used in simply spinning the flywheel/clutch assembly and that means a lot more power and torque is available at the drive wheels. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines and this is among the most advanced and lightest racing clutch kits available for your BMW race car.
The JB Ultra-Light Performance racing clutch is available in 2-disc or 3-disc setups. A 3-disc setup is less susceptible to heat and will have a higher torque capacity. On our M54-powered 325i Touring Cars (approximately 300hp) we used the 5.5"/140mm 2-disc configuration. The 5.5" clutch was a perfect blend of performance and durability. It wasn't too small to suffer from high temperatures and wasn't too large that it couldn't be slipped (slipping prevents damage to other components). This is a turn-key racing clutch and flywheel kit that you don't have to engineer or spec yourself. This is the same clutch setup we used when winning the 2003 and 2004 Touring Car Championships - the quality and performance is unquestionable. That series also employed standing starts at each race and this clutch setup performed flawlessly with nearly a full season of racing on them before needing a change.
multi-disc Sachs or Powertrain Technology racing clutch with racing pressure plate
JB Racing throw-out bearing with custom bobbin This is a true racing clutch and will not function as a street-able clutch at all. It behaves as an on/off switch with no slippage allowed. Extreme care must be used when driving on to trailers and around the paddock. But when driven correctly the life span of this clutch is amazing - we could get a full season of racing a 300hp M54 from this clutch setup including standing starts at every race! Replacement clutch components and flywheel rebuilding are available.
A properly adjusted clutch stop is required for use with this clutch kit.
Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.
Show More Show Less
