The factory BMW S55 dual-mass flywheel is engineered with comfort in mind, catering to the luxury-oriented expectations of the brand’s driving experience. Its design focuses on dampening drivetrain vibrations, smoothing out gear transitions, and minimizing harshness during operation. However, this refinement costs valuable performance. The dual-mass flywheel adds a substantial 26.5 lbs of rotational mass to the drivetrain, which significantly hinders throttle response and makes rev-matching feel sluggish and disconnected. Moreover, dual-mass flywheels are notorious for being a weak link in modified or high-performance builds and can prove costly to replace when they inevitably fail.

Our Single-Mass Lightweight Flywheel Conversion addresses all of these shortcomings with a purpose-built, lightweight, single-mass design that prioritizes performance. Weighing in at only 18.5 lbs., this design significantly reduces rotational mass, allowing your S55 to achieve its true motorsport potential!

Features & Benefits:

Precision machined from 4140 HT heat-treated chromoly steel for exceptional toughness, even wear properties, and increased durability.
Material quality promotes even wear across the entire friction surface, prolonging component lifespan.
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability.
Hardness improves component wear characteristics.
Black oxide coated for corrosion resistance on non-friction surfaces.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 certified to ensure safe operation under extreme operating conditions.
Specifically designed to work with S55 OE-architecture clutches.
Optimized step height maximizes clutch clamp load and offers a prolonged service life.
Performance:

10 lbs. lighter than the factory BMW flywheel!
OEM Dual-Mass: 26.5 lbs.
Turner Motorsport Single-Mass: 18.5 lbs.
Faster revs
Improved throttle response and acceleration
Allows for a more engaging driving experience and delivers a feeling of direct connection
Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

The factory BMW S65 dual-mass flywheel is engineered with comfort in mind, catering to the luxury-oriented expectations of the brand’s driving experience. Its design focuses on dampening drivetrain vibrations, smoothing out gear transitions, and minimizing harshness during operation. However, this refinement costs valuable performance. The dual-mass flywheel adds a substantial 27 lbs of rotational mass to the drivetrain, which significantly hinders throttle response and makes rev-matching feel sluggish and disconnected. Moreover, dual-mass flywheels are notorious for being a weak link in modified or high-performance builds and can prove costly to replace when they inevitably fail.

Our Single-Mass Lightweight Flywheel Conversion addresses all of these shortcomings with a purpose-built, lightweight, single-mass design that prioritizes performance. Weighing in at only 19 lbs., this design significantly reduces rotational mass, allowing your S65 to achieve its true motorsport potential!

Features & Benefits:

Precision machined from 4140 HT heat-treated chromoly steel for exceptional toughness, even wear properties, and increased durability.
Material quality promotes even wear across the entire friction surface, prolonging component lifespan.
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability.
Hardness improves component wear characteristics.
Black oxide coated for corrosion resistance on non-friction surfaces.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
Specifically designed to work with S65 OE-architecture clutches.
Optimized step height maximizes clutch clamp load and offers a prolonged service life.
Performance:

8 lbs. lighter than the factory BMW flywheel!
OEM Dual-Mass: 27 lbs.
Turner Motorsport Single-Mass: 19 lbs.
Faster revs
Improved throttle response and acceleration
Allows for a more engaging driving experience and delivers a feeling of direct connection
Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

Working in collaboration with Competition Clutch, the up and coming German automotive performance company DKM has released a new line of high quality clutches made to satisfy your stock and modified performance needs! If you're having problems keeping power to the wheels, DKM has the solution. Their design, using high-grade materials, gives you increased strength and heat tolerance preventing wear and fade, ensuring increased torque capacity, quicker shifts, and longer clutch life.

Tracking your vehicle is all fun and games until you start burning through clutches as fast as you can afford to replace them. To end this cycle, the MS Twin Disc Clutch Kit is designed to hold up to 100 to 200% more torque capacity and provide you with a much-improved clutch life span. The two organic disc setup provides additional contact surface areas to more evenly distribute pressure and heat for both a boost in performance and wear prevention.

Kit Contents:
Pressure Plate
Two Organic Discs
Steel Single Mass Flywheel
Pilot Bearing/Bushing and Throw-out Bearing (when applicable)
Alignment Tool

Working in collaboration with Competition Clutch, the up and coming German automotive performance company DKM has released a new line of high quality clutches made to satisfy your stock and modified performance needs! If you're having problems keeping power to the wheels, DKM has the solution. Their design, using high-grade materials, gives you increased strength and heat tolerance preventing wear and fade, ensuring increased torque capacity, quicker shifts, and a longer clutch life.

Tracking your vehicle is all fun and games until your start burning through clutches as fast as you can afford to replace them. To end this cycle, the MS Twin Disc Clutch Kit is designed to hold up to 100 to 200% more torque capacity and provide you with a much improved clutch life span. The two organic disc setup provides additional contact surface areas to more evenly distribute pressure and heat for both a boost in performance and wear prevention.

Kit Contents:
Pressure Plate
Two Organic Discs
Steel Single Mass Flywheel
Pilot Bearing/Bushing and Throw-out Bearing (when applicable)
Alignment Tool
Rated for upwards of 660 ft/lbs of torque

This kit from Valeo is a simple way to easily convert your stock dual mass flywheel clutch system to a single mass system.

Dual mass flywheels allow for fluid-feeling clutch engagements and offer a more luxurious feel than single-mass flywheels. However, with these benefits come significant drawbacks. Why convert from a dual-mass flywheel to a single-mass flywheel?

Cost: Dual-mass flywheels are expensive, with the cost of replacement often times being double or triple than that of converting to a single-mass flywheel.
Serviceability: Single-mass flywheels can be resurfaced, eliminating the need to replace with the next clutch service. - something that is not recommended with dual-mass flywheels, as they contain a rubber section that is more failure-prone in high mileage application.
Simplicity: Single-mass flywheels lack the complexity of dual-mass flywheels, making them inherently more reliable. Dual-mass flywheels contain a rubber damper or hub that will, like all rubber components, wear out with time.
Pedal Feel: Many enthusiasts prefer to eliminate BMW's "Self Adjusting Clutch", which has been known to provide an unpredictable, inconsistent engagement point.
Driveability: Valeo's conversion kit has been designed to maintain nearly identical clutch and flywheel weight, ideal for keeping the clutch quiet and easy to drive.
Kit contents:

Single-mass flywheel
Non-Self Adjusting Clutch and pressure plate
Throw out bearing
Pressure plate bolts
Flywheel bolts
Clutch alignment tool

Turner Motorsport presents the MS Twin Disc Clutch Kit (MS-006-005) by DKM®, an exceptional clutch solution designed for BMW applications. Engineered to handle 100 to 200% more torque capacity, this twin disc kit features sprung organic discs, providing increased contact surface for higher torque capacity and an extended lifecycle. The kit includes a pressure plate, organic discs, steel flywheel, pilot bearing/bushing, throw-out bearing, and alignment tool for a comprehensive clutch upgrade.

• High Torque Capacity: Holds 100 to 200% more torque to the wheels.
• Durable Construction: Sprung organic discs for longevity and increased contact surface.
• Complete Kit: Includes pressure plate, discs, steel flywheel, pilot bearing/bushing, throw-out bearing, and alignment tool.
• CNC Machined Components: Ensures precision and reliability.
• Powerful Performance: Rated for upwards of 650 ft/lbs of torque.
• Billet Steel Flywheels: Enhances strength and durability.
• Practicable Pedal Feel: Offers sport-inspired performance without sacrificing pedal feel.
• Factory-Like Engagement: Maintains a close-to-factory engagement.
• Street Capable: Ideal for high horsepower street applications.

Upgrade your BMW's clutch performance with the MS Twin Disc Clutch Kit from Turner Motorsport.

Restore your BMW MINI's performance with the complete Clutch Kit from MINI. If you're experiencing clutch slipping despite a seemingly intact slave cylinder and pedal, it's time to replace your clutch for seamless functionality.

Key Benefits:

• Complete Clutch Replacement: Includes clutch disc, pressure plate, and release bearing for a comprehensive clutch solution.
• Enhanced Performance: Restores proper clutch engagement and functionality, ensuring optimal performance for your MINI.
• Improved Driveability: Eliminates clutch slipping issues, enabling smoother gear shifts and responsive driving.
• Genuine MINI Parts: Guaranteed quality and compatibility with your MINI vehicle, ensuring reliable performance.

• Incorporates advanced "floating pressure system" for a smooth driving experience
• Retains technology from Racing Multi-plate Clutches
• Available in single and twin plate configurations
• Options for soft or hard clutch covers to suit engine output

Upgrade your Mini with the MINI F Chassis K-MAC Stage 3 Full Race - Front Adjustable Camber/Caster Plates.

These adjustable camber/caster plates offer precise control over camber and caster settings, allowing for optimized performance on the track. Crafted with high-quality materials, they ensure durability and reliability even under racing conditions. With easy adjustability and precise engineering, they provide enhanced handling and cornering capabilities, giving you a competitive edge on the race circuit.

Benefits:

• Precise control over camber and caster settings
• Optimized performance on the track
• High-quality materials for durability and reliability
• Easy adjustability
• Enhanced handling and cornering capabilities
• Competitive edge on the race circuit

Upgrade Your Clutch for Spirited Driving with STR Clutch

Elevate your driving experience with the STR Clutch, perfect for those who enjoy spirited driving and require a balance between street and occasional race performance. While it may differ from a Factory Dual Mass Clutch, the STR Clutch comes in single and twin plate configurations, paired with a unique clutch cover to maintain a factory clutch pedal feel. This ensures a race-ready clutch that's also easy to handle in everyday driving situations.

Key Features:

• Available in single and twin plate configurations
• Unique clutch cover for a factory-like pedal feel
• Suitable for spirited driving and occasional racing
• Dampened Single Plate with Soft Diaphragm
• Release Assembly included
• Maximum capacity: 285 FT/LBS TORQUE

Upgrade your clutch and enjoy the performance and versatility of the STR Clutch.