Valve Cover

Valve Cover Gasket Overhaul Kit - E9X 328i, E60 528i, E83 X3 3.0i/si,...

T#:180875

Part#: TMS180875

In Stock

$ 142.24

This product was last offered at the strikethrough price on
05-07-2026

$ 107.33 USD

Add to Wish List

Qty

$ 107.33 USD

Add to Wish List

Not only will this kit stop most E90 oil leaks, it's the perfect addition for ignition coil or spark plug replacement! Oil leaks - and the damage they can cause - seem to be the worst annoyances on these cars. The biggest source of an oil leak is from the valve cover, followed by the oil filter housing, Valvetronic seal, camshaft seals, and the eccentric shaft sensor seal. Once the oil leaks, and if ignored for an extended time, the oil will contaminate vital electrical sensors. This is especially the case with ignition coils and also the eccentric shaft sensor on the Valvetronic shaft at the top of the cylinder head. During any ignition coil and spark plug replacement take a close look inside for any oil pooling at the bottom. We have been seeing valve cover oil leaks as soon as 40,000 miles. We look for oil leaks on every E90 that comes into our shop.

We have put together this package of valve cover gaskets and other related gaskets and seals for you to fully overhaul the N52 valve cover and put a stop to those pesky oil leaks. This package has the replacement parts for N52 engines built from the 2007 model year and includes:

11127582245 - N52 valve cover gasket set
11127552280 - N52 eccentric shaft sensor seal
11127559699 - N52 Valvetronic gasket

2007 and later N51/N52 engines do not need replacement valve cover bolts, unless the bolts are actually broken off or missing. Unlike the 2006 aluminum hardware, the later parts are steel and not 1-time use.

These are all OEM or OE parts. Replacement of these gaskets and seals is straight-forward but a long process. BMW dealers typically charge for over eight hours of labor. If you have replaced spark plugs before you should be capable of this repair. In addition, there are several other parts to replace while you're in the vicinity: camshaft sensor o-rings, oil filter housing profile gasket, VAN0S solenoids, and the eccentric shaft sensor. These other parts, except the eccentric shaft sensor (see below), are replaceable without removing the valve cover but are more easily accessed during the valve cover work.

Eccentric Shaft Sensor: This is the position sensor that relays the eccentric shaft's position back to the DME. It's located at the front of the engine and is only accessible with the valve cover off . The seal around the sensor can fail and allow oil to blow out from under the cam cover. Oil can then leak into the sensor itself and cause it to fail. Without a functioning sensor your E90 can experience poor running, hesitation, poor performance, jerky shifts, and sluggish response. It's easy to check and see if oil has accumulated inside the sensor: unbolt the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside or even around the sensor itself, plan on replacing this sensor during your next ignition coil, spark plug, and/or valve cover gasket work.

This valve cover kit fits the following BMWs:
2008-2012 E82 BMW 128i
2007-2011 E90 BMW 328i 328xi 328i xDrive - Sedan
2007-2012 E91 BMW 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2007-2010 E60 BMW 528i 528xi 528i xDrive
2011 F10 BMW 528i
2007-2010 E83 BMW X3 3.0i X3 3.0si
2007-2013 E70 BMW X5 3.0si
10/2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive30i

Show More Show Less

Rein Valve Cover Kit - N52

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:599640

Part#: 11127552281

In Stock

$ 355.99

This product was last offered at the strikethrough price on
06-19-2026

$ 312.99 USD

Add to Wish List

Qty

$ 312.99 USD

Add to Wish List

Enhance your BMW's performance with this comprehensive valve cover assembly, complete with a sealing gasket and engine cover mounts.

Key Benefits:
- Comprehensive valve cover assembly for BMW engines
- Includes sealing gasket for optimal performance
- Engine cover mounts ensure a secure fit
- Enhances overall engine efficiency and longevity

Show More Show Less

Rein Valve Cover - BMW N55

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:34114257

Part#: 11127570292

In Stock

$ 254.99 USD

Add to Wish List

Qty

$ 254.99 USD

Add to Wish List

Valve Cover by Rein is a crucial component designed to protect and seal the top of your BMW’s engine, ensuring optimal performance and preventing oil leaks. Engineered specifically for BMW engines, this high-quality valve cover provides a precise fit and exceptional durability. Available at Turner Motorsport, the Valve Cover by Rein offers long-lasting reliability, protecting critical engine components from damage while maintaining proper oil pressure.

Designed specifically for BMW engines for perfect fit and function
Prevents oil leaks, maintaining proper engine lubrication
Made from high-quality, durable materials for long-lasting performance
Direct-fit replacement ensures hassle-free installation
Protects critical engine components and improves engine efficiency
Helps maintain proper oil pressure for optimal engine performance

The Valve Cover VCE0101 by Rein from Turner Motorsport is the ideal solution for BMW owners seeking to protect their engine, prevent oil leaks, and ensure reliable performance.

Show More Show Less

Valve Cover Kit - N55

T#:5376284

Part#: 11127570292TKT

In Stock

Sale - Save 5% $ 320.99

This product was last offered at the strikethrough price on
05-03-2026

$ 304.52 USD

Add to Wish List

Qty

Sale - Save 5%

$ 320.99

This product was last offered at the strikethrough price on
05-03-2026

$ 304.52 USD

Add to Wish List

If your valve cover has become cracked or warped, replace it with this Hamburg Tech cover from Turner Motorsport to prevent leaks and further valvetrain damage. Replace your leaking valve cover to keep your oil inside the engine, where it belongs. Includes everything needed to install a new valve cover: Valve cover Gasket flange Crank case vent hose Hardware

Show More Show Less

N54 Valve Cover upgrade kit

T#:6196925

Part#: 11127565284TKT

In Stock

Sale - Save 30% $ 423.99

This product was last offered at the strikethrough price on
05-03-2026

$ 296.23 USD

Add to Wish List

Qty

Sale - Save 30%

$ 423.99

This product was last offered at the strikethrough price on
05-03-2026

$ 296.23 USD

Add to Wish List

You want to keep your N54 running properly to enjoy the drive and justify the costs associated with owning an N54 car! This kit has a replacement valve cover for your current cover that is worn or damaged. Along with replacing the valve cover this kit includes an upgraded pcv valve. This upgraded PCV valve uses machined metal components in place of the stock plastic parts, resulting in a more durable part. While replacing your valve cover a common failure is one of the blow by pcv vent hose cracks and is also INCLUDED in the kit for a full proof valve cover upgrade service! Replace and upgrade your valve cover at the same time, with the VTT PCV valve for longer PCV life and better flow.

Show More Show Less

URO Valve Cover Kit - E82 128i, E9X 328i, E60 528i, E70 X5 3.0si, E83...

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat! For 2007+ models with plastic valve cover

T#:395230

Part#: 11127552281

Ships in 1 Business Day

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

All-in-one valve cover overhaul Preventative replacement saves time and trouble later on Includes new oil separator system Replace valve cover gaskets before a leak becomes worse Replace valve cover before it cracks For the 2007 model year BMW switched to a plastic valve cover on the N51 and N52 engines. As we have seen over time the plastic can crack which leads to oil leaks, vacuum leaks, poor running, and other issues. Unfortunately, it's not just the gasket that needs periodic replacement but the entire valve cover itself. This kit includes a new valve cover, gaskets, eccentric shaft seal, and hardware. The valve cover also incorporates the oil separator which is not a replaceable item on its own. So a complete valve cover replacement will tackle multiple problem areas at once. The valve cover is the same for N51 SULEV and N52 engines. Cracked Valve Cover. The plastic used for the N52 valve cover is thin and weak in certain spots. This makes it prone to hairline or larger cracks that will leak oil and cause vacuum leaks. You might also notice rough running, especially at idle. Often a technician will go looking for a failed ignition coil, spark plug, or failed vacuum hose on the engine. And without a fault code to assist in diagnosis this can often mean wasted time and money. A cracked valve cover is a new problem area that many techs don't think to check. Oil Separator/Crankcase Vent. BMW integrated the oil separator system into the valve cover on these later engines. An internal manifold creates a cyclone effect and centrifugal force separates vapor from the liquid oil. The liquid oil is supposed to drain through the valve cover and back to the oil pan while the remaining vapor is burned up during combustion. It's a very efficient and environmentally-friendly design with very few moving parts. Unfortunately it's not perfect and eventually the internal passageways will become clogged. This problem is made worse in cars that have short drive cycles, sit for long periods of time, do not have frequent oil changes, do not see regular runs to redline, and cars in freezing climates. If the engine never reaches optimal operating temp the oil remains in liquid form or becomes sludge. This is bad news for the entire engine, leading to fouled spark plugs, rough running and misfires and even premature failure of catalytic converters and oxygen sensors. Since the oil separator system in the valve cover is not available on its own, and cleaning it is nearly impossible, the complete replacement of the valve cover is the only option. Other oil vent tubes and vacuum hoses are also recommended to get replaced at the same time. Valve Cover Gaskets. As with any rubber part, failures occur when the rubber becomes dry and brittle. The pliable rubber no longer forms a seal between the cylinder head and valve cover where it will develop an oil leak. Valve cover gaskets that leak can allow oil to seep into the spark plug holes and contaminate ignition coil boots and plugs. That can lead to rough running and misfires. A new valve cover includes new gaskets. Eccentric Shaft Seal. The seal for the eccentric shaft sensor is a known spot for oil leaks. When the seal to the valve cover fails oil can end up in the sensor itself and ruin the sensor (an unecessary $300 expense). Usually a new seal (o-ring) will stop the leaks but sometimes the valve cover is at fault too. A new eccentric shaft seal is included. All new hardware is included to avoid re-using and over-tightening the original bolts (they have a very low torque rating). Replacement requires accessing the rear of the engine with a lot of the upper plastic shrouding removed. The vent hose on the valve cover should be replaced as it is almost always broken anyway (#11157559528). The metal fuel line must also be removed and disconnected from the fuel injectors. Professional installation is encouraged if you have never done this kind of work before. Serious DIY types should have a Bentley Service Manual to use which greatly explains the process. You may also want to combine this work with the oil filter housing gasket replacement. There is no maintenance or replacement interval for the N52 valve cover. However, we have seen cracks and other failures in the 50,000-90,000 mile range. Our best advice is to plan on a major top end overhaul around the 70-80,000 mile mark. There's no mechanical downside to replacing it as prevention and it will make the engine run better and last longer. This item fits the following BMWs: 2008-2012 E82 BMW 128i 2007-2011 E90 BMW 328i 328xi 328i xDrive - Sedan 2007-2012 E91 BMW 328i 328xi 328i xDrive - Wagon 2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe 2007-2013 E93 BMW 328i - Convertible 2008-2010 E60 BMW 528i 528xi 528i xDrive 2011 F10 BMW 528i 2007-2010 E83 BMW X3 3.0i X3 3.0si 2007-2008 E70 BMW X5 3.0si 2007-2008 E85 BMW Z4 3.0i Z4 3.0si 2009-2010 Z4 BMW Z4 sDrive30i

Show More Show Less

Valve Cover - Left

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:583194

Part#: 11127522159

Ships in 1 Business Day

$ 195.37 USD

Add to Wish List

Qty

$ 195.37 USD

Add to Wish List

Valve cover for N62 V8, left bank, Cylinders 5-8 Includes gaskets and bolts.

Valve Cover Gasket Set - E36 E39 Z3 with M52

T#:337951

Part#: 11120034108

In Stock

Starting at $ 70.25 USD

Add to Wish List

Starting at $ 70.25 USD

Add to Wish List

Original BMW replacement valve cover gaskets, including large cover gasket and spark plug cavity gaskets. Fits M52 engine with single VAN0S. This is the OE BMW gasket rather than an OEM or aftermarket brand - we have found the OE gaskets are a better seal than the others.

Alternate BMW part numbers:
11129070532

This item fits the following BMWs:
1996-1999 E36 BMW 323is 323ic 328i 328is 328ic
1996-1999 E36 BMW M3
1997-1998 E39 BMW 528i
1997-1998 Z3 BMW Z3 2.8
1998-2000 Z3 BMW M Roadster M Coupe

Show More Show Less

Valve Cover Gasket Set - E39 M5, E52 Z8

T#:214354

Part#: TMS214354

Ships in 1-2 days

$ 265.32

This product was last offered at the strikethrough price on
03-02-2026

$ 264.92 USD

Add to Wish List

Qty

$ 264.92 USD

Add to Wish List

Replacement valve cover gaskets, including large cover gaskets and seals and grommets. Fits E39 M5 and E52 Z8 with S62 engine.

Kit includes:
11120001269 - Valve Cover Gasket Cyl 1-4
11120001278 - Valve Cover Gasket Cyl 5-8
11121721879 - Valve Cover Seals x 6
11121437395 - Valve Cover Seal Grommet x 20

This item fits the following BMWs:
2000-2003 E39 BMW M5
2000-2003 E52 BMW Z8 Roadster

Show More Show Less

MINI N18 Engine Valve Cover With PCV

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:599579

Part#: 11127646552

In Stock

$ 195.45 USD

Add to Wish List

Qty

$ 195.45 USD

Add to Wish List

MINI N18 Engine Valve Cover With PCV addresses two common issues: check engine light codes and oily leaks from the top of the valve cover. This replacement valve cover features a black exterior without a front cover or MINI wings logo, effectively replacing damaged or cracked covers. It ensures that engine oil remains contained and prevents dirt from entering.

Dual Functionality: Resolves check engine light issues and prevents oil leaks from the valve cover.
Integrated PCV Valve: Helps prevent excessive oil consumption, carbon build-ups, and recurring check engine light problems.
Complete Kit: Includes valve cover gasket, spark plug tube seals, installation bolts, and oil cap with seal.
High-Quality Construction: An OES supplier part designed for reliable performance and a perfect fit.

Show More Show Less

Valve Cover - Right

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:583193

Part#: 11127563474

In Stock

$ 202.28 USD

Add to Wish List

Qty

$ 202.28 USD

Add to Wish List

Valve cover for N62 V8, right bank, Cylinders 1-4 Includes gasket and bolts.

N54 Valve Cover

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:399428

Part#: 11127565284

In Stock

Sale - Save 20% $ 285.66

This product was last offered at the strikethrough price on
05-15-2026

$ 229.19 USD

Add to Wish List

Qty

Sale - Save 20%

$ 285.66

This product was last offered at the strikethrough price on
05-15-2026

$ 229.19 USD

Add to Wish List

With more than 4,000 European vehicle replacement parts, URO is no stranger to the market. Superior metal stock and extremely strict quality control are at the forefront of URO’s agenda and it shows as they become the OE supplier for more and more car companies every single day.

Show More Show Less

MINI R53 Valve Cover Without MINI Label

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:600487

Part#: 11128658461

In Stock

$ 178.42

This product was last offered at the strikethrough price on
03-17-2026

$ 153.98 USD

Add to Wish List

Qty

$ 153.98 USD

Add to Wish List

MINI R53 Valve Cover Without MINI Label is an excellent replacement for the factory valve cover on your MINI. Featuring a sleek black exterior, this cover does not include the MINI logo, which is sold separately. It is designed to replace damaged or cracked valve covers, effectively keeping engine oil contained and preventing dirt from entering the engine.

Compatible Fit: Designed for R50, R52, and R53 Gen 1 engines, both supercharged and non-supercharged.
Complete Kit: Includes valve cover gasket, spark plug tube seals, and preloaded with valve cover screws and bolts.
Additional Components: Comes with an oil cap and seal for easy installation.
PCV Valve Compatibility: Suitable for screw-in style PCV valves (ES#18656); verify existing PCV valve type before purchasing.

This valve cover ensures a reliable seal and protection for your engine, maintaining optimal performance.

Show More Show Less

Valve Cover Screws Kit

T#:7844460

Part#: 11121487179KT11

In Stock

$ 157.61 USD

Add to Wish List

Qty

$ 157.61 USD

Add to Wish List

This collar screw is needed to attach the valve cover and seal it to the engine head. Finally be able to replace your hardware before its too late and the valve cover is stuck on and the hardware needs drilled out. Included in this kit to replace the ru

Show More Show Less

Valve Cover - With PCV Valve

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:594483

Part#: 11127588412

In Stock

Sale - Save 7% $ 326.99

This product was last offered at the strikethrough price on
07-15-2026

$ 304.41 USD

Add to Wish List

Qty

Sale - Save 7%

$ 326.99

This product was last offered at the strikethrough price on
07-15-2026

$ 304.41 USD

Add to Wish List

Valve Cover With PCV

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:559337

Part#: 11127646555

In Stock

$ 151.38 USD

Add to Wish List

Qty

$ 151.38 USD

Add to Wish List

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:599655

Part#: 11127512839

Ships in 3 Business Days

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

OEM Rein Valve Cover - F22/23 F3X N20 2.0L

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat! For vehicles with the N26 SULEV engine only

T#:639079

Part#: 11127633630

In Stock

$ 285.99 USD

Add to Wish List

Qty

$ 285.99 USD

Add to Wish List

Is your valve cover cracked, warped, or otherwise faulty? This valve cover from OEM Rein is a perfect replacement option to guarantee a factory-like fit and reliability!

OEM Rein Valve Cover Kit - BMW M52TU M54

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:599656

Part#: 11121432928

Back Ordered

$ 233.99 USD

Add to Wish List

Qty

$ 233.99 USD

Add to Wish List

Eliminate oil and vacuum leaks with a brand new valve cover. This OEM Rein valve cover comes complete with sealing gaskets and engine cover mounts.

Valve Cover

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:559290

Part#: 11127512839

Ships in 1 Business Day

$ 270.99

This product was last offered at the strikethrough price on
05-07-2026

$ 256.99 USD

Add to Wish List

Qty

$ 256.99 USD

Add to Wish List

This complete valve cover assembly includes a sealing gasket and engine cover mounts.

Valve Cover Gasket Set - E36 E34 with M50 VANOS

T#:337950

Part#: 11120034107

In Stock

Sale - Save 3% $ 98.99

This product was last offered at the strikethrough price on
07-06-2026

Starting at $ 96.34 USD

Add to Wish List

Sale - Save 3%

$ 98.99

This product was last offered at the strikethrough price on
07-06-2026

Starting at $ 96.34 USD

Add to Wish List

Original BMW replacement valve cover gaskets, including large cover gasket and spark plug cavity gaskets. Fits M50 (M50TU) engine with VAN0S. This is the OE BMW gasket rather than an OEM or aftermarket brand - we have found the OE gaskets are a better seal than the others.

Alternate BMW part numbers:
11129070531

This item fits the following BMWs:
1993-1995 E36 BMW 325i 325is 325ic
1995 E36 BMW M3
1993-1995 E34 BMW 525i

Show More Show Less

Valve Cover Replacement Kit - N54 3.0L

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:599653

Part#: 11127565284

In Stock

$ 361.99 USD

Add to Wish List

Qty

$ 361.99 USD

Add to Wish List

Enhance your BMW N54 3.0L engine with the Valve Cover Replacement Kit. This comprehensive kit includes a complete valve cover assembly with a gasket, bolts, and integral cyclone separator. Ensure optimal engine performance and prevent leaks with this high-quality replacement kit designed specifically for the N54 engine.

Valve Cover Replacement Kit for BMW N54 3.0L
Complete assembly with gasket, bolts, and integral cyclone separator
Ensures optimal engine performance
Prevents leaks for enhanced reliability
Quality components for long-lasting durability

Show More Show Less

Valve Cover - with PCV Valve

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:584545

Part#: 11127588412

Ships in 1 Business Day

$ 257.99 USD

Add to Wish List

Qty

$ 257.99 USD

Add to Wish List

Replacement Valve cover

URO Valve Cover - N47

2X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat!

T#:2438648

Part#: 11128589942

Ships in 1 Business Day

$ 383.99

This product was last offered at the strikethrough price on
05-07-2026

$ 355.99 USD

Add to Wish List

Qty

$ 355.99 USD

Add to Wish List

The positives crank ventilation valve (PCV) is integrated into the top of the valve cover and tends to stick, causing massive oil consumption, carbon build-ups, and check engine lights down the road.