Find Parts That Fit Your Vehicle

Engine Hardware

Most engine hardware including head studs, VANOS bolts, and exhaust studs can only be used once. While most of the accessory bolts and miscellaneous hardware can be re-used it is often handy to have a spare bolt or bracket just in case one breaks. Any aluminum bolt, such as those found in the N52 engine MUST be replaced no matter the age or visual condition.

Sort By:

BMW E9x M3 - BE Bearings Performance Rod Bearing Replacement Kit w/o ...

T#:13463763

Part#: 11247838088DBEKT

In Stock

$ 974.99 USD

Add to Wish List

Qty

$ 974.99 USD

Add to Wish List

Don't fall victim to the notorious rod bearing issues of the S65 engine in your BMW E90, E92, or E93 M3, especially if your engine has higher mileage. Protect your engine from catastrophic failure by proactively replacing your rod bearings. BE Bearings, in collaboration with Clevite, a leading OE bearing manufacturer, has revolutionized rod bearings for your peace of mind. Our redesigned bearings offer enhanced clearance and feature a shift from the original tin-aluminum composition to lead-copper. This upgrade incorporates the cutting-edge Clevite Tri-Metal design and boasts a Tri-Armor™ coating, ensuring superior lubrication for wear prevention. Moreover, these softer bearings are gentler on your engine and more tolerant of foreign particles suspended in your oil. Additionally, this upgrade enables precise wear assessment through oil testing. Our comprehensive kit includes: Upper and lower BE Bearings upgraded rod bearings Essential hardware Oil filter Oil pan gasket RedLine assembly lube Secure your BMW E90, E92, or E93 M3's engine with our rod bearing kit and enjoy peace of mind on the road.

Show More Show Less

Athena Cut Ring Head Gasket - 84.5mm - BMW M50 M52 (84mm Bore) ...

T#:26171655

Part#: ATH-HG-CR-M50-84

In Stock

$ 324.99 USD

Add to Wish List

Qty

$ 324.99 USD

Add to Wish List

Upgrade your BMW engine's performance with the Athena Cut Ring Head Gasket. This gasket replaces BMW part # 11121726619 and 11121726617 and is specifically designed for M50 & M52 iron block inline 6-cylinder engines found in E34/E36 chassis. Standard OEM & MLS gaskets can only handle a certain amount of cylinder pressure before they start to leak, making the Athena Cut Ring Head Gasket the recommended choice for applications making 16+ psi. A compression leak passing the head gasket can cause a range of issues, including engine overheating, loss of power, misfires, and in severe cases, catastrophic engine failure. Athena's gasket is crafted with premium quality reinforced M0115, an asbestos-free material that's original equipment approved and renowned for its superior quality. The AISI 304 stainless steel Cooper Rings bite into the aluminum head, providing maximum sealing capabilities around the cylinder bore and optimizing engine performance, even on engines with nitrous and/or turbo applications that exceed 2-bar boost. Before installation, it is crucial to have the mating surfaces of the cylinder head and block professionally cleaned and resurfaced to ensure they are completely flat. Please be aware that the gasket should have a size that is 0.5mm to 1mm larger than the piston. For example, if the piston measures 84mm, then the gasket should be the next size up, either 84.5mm or 85mm. Installation instructions: Make sure that the engine block and cylinder head surfaces are clean, flat, and free from any debris, oil, or coolant. Install the Cut Ring gasket on the engine block and ensure that it is properly aligned. Avoid twisting or bending the gasket during installation. Place the cylinder head on top of the gasket and install the head bolts or studs in their correct positions. Follow the manufacturer's recommended torque specifications and tighten the bolts or studs in the proper sequence to ensure even clamping force across the gasket. After the initial tightening, re-torque the head bolts or studs after the engine has been started and then allowed to cool to room temperature. This will ensure that the gasket is properly seated and compressed. It is recommended to not use any additional sealant on the MLS gasket, as it is already coated with a Viton rubber sealant. Using additional sealant can hinder the performance of the gasket.

Show More Show Less

BMW S58 3.0L ARP Head Stud Kit - CA625+

T#:22427036

Part#: ARP-HSK-S58-CA

Ships in 4 Business Days

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

BMW S58 3.0L ARP Head Stud Kit - CA625+ is the ultimate upgrade for the BMW S58 engine, specifically designed for high-performance models such as the F97 X3M, F98 X4M, G80 M3, G82 M4, G83 M4, and G87 M2. Manufactured by Turner Motorsport, this head stud kit ensures optimal engine reliability and performance.

Enhanced Strength: Featuring Custom Age 625+ material with a tensile strength of 260 ksi, this kit provides superior strength compared to factory bolts.
Prevents Head and Block Separation: Designed to handle increased boost levels and high-stress conditions, preventing potential head and block separation.
Precision Engineering: ARP’s advanced manufacturing process ensures that these head studs outperform standard factory bolts under extreme conditions.
Ideal for High-Performance Builds: Perfect for enthusiasts pushing the limits of their S58 engines, offering unparalleled durability and reliability.
Direct Fit: Specifically tailored for the turbocharged inline 6-cylinder BMW S58 engine, ensuring a seamless installation and optimal performance.

Show More Show Less

ARP Main Stud Kits - S58

T#:22427031

Part#: ARP-MSK-S58

Ships in 4 Business Days

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Elevate your BMW S58 engines with the ARP Main Stud Kit, replacing part numbers 11118604584. These studs prevent main cap walk, ensuring stability and protecting the engine from potential damage. They also safeguard the engine block threads, adding an extra layer of protection. Opting for main studs over factory bolts requires engine builders to mic the bores. Studs may require a line hone for proper fitment and alignment, ensuring round and concentric main bearing bores, preventing premature bearing wear, and ensuring optimal oil clearance.

Project Cars

SELECT YOUR BMW

Engine Hardware

BMW E9x M3 - BE Bearings Performance Rod Bearing Replacement Kit w/o ...

Athena Cut Ring Head Gasket - 84.5mm - BMW M50 M52 (84mm Bore) ...

BMW S58 3.0L ARP Head Stud Kit - CA625+

ARP Main Stud Kits - S58

Select Vehicle

Purpose

Category

Brand

Price

Shipping

Narrow Results