Flywheels

Engineered in-house, our torque plate is designed to provide a robust and uniform clamping surface between the flywheel and crankshaft across a range of BMW engine applications. Compatible with both factory and Turner performance flywheels, it helps prevent surface galling and ensures consistent torque distribution during installation.

Features:

Prevents galling and wear at the crankshaft-to-flywheel interface under high clamping loads
Promotes even load distribution for improved fastener integrity and long-term reliability
Compatible with a variety of BMW flywheel setups, including OEM and aftermarket configurations
Design:

Precision-machined from cold rolled steel for high strength and dimensional accuracy
Heat treated to 32 HRC for increased surface hardness and wear resistance
Clear zinc anodized for enhanced corrosion protection
Laser-etched Turner logo
Ideal for performance builds and drivetrain refreshes, this torque plate is a critical component for maintaining proper flywheel installation and maximizing long-term durability across multiple BMW platforms.

The factory BMW S55 dual-mass flywheel is engineered with comfort in mind, catering to the luxury-oriented expectations of the brand’s driving experience. Its design focuses on dampening drivetrain vibrations, smoothing out gear transitions, and minimizing harshness during operation. However, this refinement costs valuable performance. The dual-mass flywheel adds a substantial 26.5 lbs of rotational mass to the drivetrain, which significantly hinders throttle response and makes rev-matching feel sluggish and disconnected. Moreover, dual-mass flywheels are notorious for being a weak link in modified or high-performance builds and can prove costly to replace when they inevitably fail.

Our Single-Mass Lightweight Flywheel Conversion addresses all of these shortcomings with a purpose-built, lightweight, single-mass design that prioritizes performance. Weighing in at only 18.5 lbs., this design significantly reduces rotational mass, allowing your S55 to achieve its true motorsport potential!

Features & Benefits:

Precision machined from 4140 HT heat-treated chromoly steel for exceptional toughness, even wear properties, and increased durability.
Material quality promotes even wear across the entire friction surface, prolonging component lifespan.
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability.
Hardness improves component wear characteristics.
Black oxide coated for corrosion resistance on non-friction surfaces.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 certified to ensure safe operation under extreme operating conditions.
Specifically designed to work with S55 OE-architecture clutches.
Optimized step height maximizes clutch clamp load and offers a prolonged service life.
Performance:

10 lbs. lighter than the factory BMW flywheel!
OEM Dual-Mass: 26.5 lbs.
Turner Motorsport Single-Mass: 18.5 lbs.
Faster revs
Improved throttle response and acceleration
Allows for a more engaging driving experience and delivers a feeling of direct connection
Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

Lightweight flywheel for quicker, effortless revs that improve throttle response and free up lost horsepower. Tested and approved by our engineering team at Turner Motorsport. Tested in early, late, ETA and IS model E30s for confirmed fitment.

Introducing our Turner Flywheel: an ingenious blend of lightweight design, rich features, and remarkable strength! Crafted from 4140 HT Steel, this flywheel is precision-machined from a solid piece, ensuring unmatched durability. By strategically trimming excess weight from its original design, we've achieved a significant reduction in weight, giving new life to your M20 engine. With upgraded efficiency, your M20 can now swiftly spin to high RPMs, unleashing the full power and prowess of this formidable engine. Our flywheel features a ring gear profile compatible with all starters, alongside a reference tab tailored for early cars equipped with bellhousing-mounted sensor crank position detection.

Do you have an early model transmission with the crank sensors on the bellhousing? Maybe you have a late 325is with the crank sensor on the front of the engine, or maybe you have a 1988 super ETA. No matter which E30 model you have, our flywheel is the perfect choice for you.

During the engineering process we encountered the full spectrum of M20 and flywheel combinations. Early cars with bellhousing crank sensors, late cars with front mounting crank sensors and even a super ETA. On this adventure we found both early and late single mass flywheels and even the dual mass that we thought for sure was just a myth. At first we were hesitant that we could make one flywheel to fit them all but with the persistence of our engineering team(fleet of E30 enthusiasts) we can proudly say our M20 flywheel does in fact fit all engine and transmission applications you can think of.

Features and benefits:

Fits early and late models with M20
Fits shallow and deep bellhousing transmissions
Ring gear suited for both starters (P# 12411726504 + 12411361874)
Heavier than other lightweight flywheels, lighter than OEM, its like the Goldie Locks of flywheels - its just right
Reference pin for bellhousing crank sensor
Strong Single-Piece 4140 HT Steel construction
Designed to be used with factory and OE clutches
Weight Comparisons:

​Factory single mass flywheel EARLY (11221705046) - 23.69 lbs.
Factory single mass flywheel LATE (11221706573) - 18.74 lbs.
Dual mass flywheel (21211225979) - 27.56 lbs.
Turner flywheel - 14 lbs.
What you need:

Short bellhousing transmissions (I/IS) - Throw-out bearing P# 21517521471
Tall bellhousing transmission (ETA) - Throw-out bearing P# 21511204525

Adapt an N54 or N55 GS6-53BZ transmission to your M5x/S5x engine to unlock superior torque capacity and optimized gear ratios.

Engineered for the BMW enthusiast who demands more strength and better gear ratios, the Turner Motorsport Transmission Swap Flywheel Kit provides a direct solution for mating a modern N54 or N55 6-speed gearbox to your M20, M5X, or S5X engine. This kit bridges the gap between generations, allowing you to run a high-capacity GS6-53BZ transmission without the typical fabrication nightmares.

The technical core of this kit is our dual-geometry flywheel. By utilizing this specialized design, you can retain your engine-side stock starter while using the factory clutch and throw-out bearing from your donor transmission. This ensures a precise fit and a firm, factory-like shifting feel that can handle significantly more power than older 5-speed setups. To guarantee a fitment, we’ve included a precision drill guide for bellhousing alignment and a universal pilot bearing pin to simplify the installation process.

Features and benefits:

Compatible with the starter from your original motor.
Uses factory clutch and throwout bearing from the donor transmission (GS6-53BZ).
Comes with necessary tools and a provided drill guide to adapt the top transmission mounting holes.
Kit contents:

Swap Flywheel
Pilot bearing input adapter for late N54 and N55 GS6
Drill guide, bit, and hardware.
Flywheel bolts
Optional pilot bearing
Optional clutch
Swap notes:

Fits M20/M50/M52/S50/S52/S54 engines
Needs a custom driveshaft and rear transmission mount. (We used https://www.hdtautoparts.com/driveshafts)
For E46 only: Rear transmission mount can be used from E46 330 6 Speed. Part numbers (22316760531 & 22316760532)
Installation and Support:

Click HERE for installation instructions:

The ACT Streetlite flywheel offers the following benefits:

Noticeably improved engine response and acceleration: Experience a significant boost in engine performance and acceleration with this component. OE to mild gear rattle: Expect only minimal gear rattle, from Original Equipment (OE) standards to a mild level, ensuring a smoother drive. Heat-treated forging for strength and toughness: Crafted using heat-treated forging, this part guarantees enhanced strength and durability. Induction-hardened ring gears for maximum life: The ring gears undergo induction hardening, providing maximum lifespan and reliability. One-piece construction allows less opportunity for failure and provides uniform efficient heat transfer from the clutch disc: The one-piece design reduces potential failure points and ensures uniform and efficient heat transfer from the clutch disc, preventing issues like warped inserts or loose ring gears. Recommended for street and race use: This component is ideal for both everyday street driving and competitive racing environments.

Forged, CNC machined, and dynamically computer balanced for smooth high RPM reliability: Expertly forged, CNC machined, and dynamically balanced via computer to ensure smooth and reliable performance at high RPMs.

BMW E36 M3 Z3 XACT Flywheel Streetlite is a high-performance upgrade designed to enhance engine response and acceleration. This Streetlite flywheel is significantly lighter than the stock flywheel, offering superior durability and strength. Crafted from Chromoly Steel, it provides excellent heat tolerance and rigidity, making it ideal for both street and drag racing applications.

• Improved Performance: Noticeably enhances engine response and acceleration with minimal gear rattle.
• Durability: Heat-treated forging ensures strength and toughness, while induction-hardened ring gears extend lifespan.
• Quality Construction: One-piece design prevents failure, ensuring uniform heat transfer and preventing issues like warped inserts or loose ring gears.
• Recommended Use: Suitable for both street and race applications.
• ACT Advantage: Forged, CNC machined, and dynamically balanced for reliable high RPM performance.

Specifications:

• Product Weight: 15.2 lbs
• Material: Chromoly Steel
• Friction Surface Diameter: 9.4 inches (240 mm)
• Flywheel Type: Streetlite
• Tooth Quantity: 113
• Warranty: 12 Months
• SFI Rating: 1.1