Single Mass Flywheel

ARP Performance Flywheel 28mm Bolt Kit - M20 2.5L

T#:302365

Part#: 201-2802

In Stock

$ 65.99 USD

Add to Wish List

Qty

$ 65.99 USD

Add to Wish List

ARP Flywheel Bolts are a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated, ensuring complete heat penetration, to increase the clamping load up to 200,000 psi. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best bolts we've found and we highly recommend them in any and all applications.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMW Engines:
M20 2.5L

Show More Show Less

E36 M3, MZ3 JB Racing Lightweight Aluminum Flywheel

T#:3771

Part#: 520-010-240

Ships in 9 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.5lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1995-1999 E36 BMW M3
1998-2002 Z3 BMW Z3 M Roadster M Coupe

Show More Show Less

E30 318i/is, E36 318i, Z3 1.9 JB Racing Lightweight Aluminum Flywheel...

T#:3769

Part#: 520-040-215

Back Ordered

11% off MSRP $ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Qty

11% off MSRP

$ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 27.0lbs
JB Flywheel Weight = 9.0lbs

This item fits the following BMWs:
1989-1992 E30 BMW 318i 318is 318ic
1992-1997 E36 BMW 318i 318is 318ti 318ic
1996-1997 Z3 BMW Z3 1.9

Show More Show Less

E60, E82, E85, E9X, E89 (N52 Engine) JB Racing Lightweight Aluminum F...

T#:2801

Part#: 520-200-240

In Stock

$ 714.00 USD

Add to Wish List

Qty

$ 714.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This JB flywheel replaces the stock flywheel and can be used with either the stock 228mm or stock 240mm clutch discs. Depending on the model you may have either clutch size in your car but this flywheel is compatible with both. You can install a 240mm clutch as a mild upgrade.

Stock Flywheel Weight = 24-31.0lbs
JB Flywheel Weight = 12.0lbs

This item fits the following BMWs:
2006-2010 E60 BMW - 525i, 528i, 530i
2006-2013 E90, E91, E92, E93 BMW - 325i, 328i, 330i
2007-2013 E82 BMW - 125i, 128i
2006-2008 E85, E86 BMW - Z4 3.0i, Z4 3.0si
2009-later E89 BMW - Z4 3.0i

Show More Show Less

E46 M3 6MT JB Racing Lightweight Aluminum Flywheel

T#:302739

Part#: 520-180-240

Ships in 8 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
2001-2006 E46 BMW M3 (6-speed manual only, not for SMG)

Show More Show Less

E46 323/325/328/330 5-speed, Z3 2.3/2.8/3.0 JB Racing Lightweight Alu...

T#:4227

Part#: 520-140-240

In Stock

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (with 5-speed manual transmission)
2001-2005 E46 BMW 325xi 330xi
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i

Show More Show Less

JB Racing Single Mass Lightweight Aluminum Flywheel - 6-speed - E46 3...

T#:3474

Part#: 520-190-240

Ships in 4 Business Days

$ 672.00 USD

Add to Wish List

Qty

$ 672.00 USD

Add to Wish List

This is a performance replacement for BMW Part # 21207533868 Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB Flywheel includes the pilot bearing mounted in the flywheel hub, just like the factory configuration.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.5lbs

This item fits the following BMWs:
2002-2005 E46 BMW 325i 330i (with 6-speed manual transmission)

Show More Show Less

E30 325i, E34 525i (M20) JB Racing Lightweight Aluminum Flywheel (Rep...

T#:385699

Part#: 520-060-228

Ships on Sep 9, 2026

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325i up to 12/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 18.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1984-1991 E30 BMW 325i 325ic 325is (with single-mass flywheel)
1989-1990 E34 BMW 525i (with single-mass flywheel)

Show More Show Less

E34 M5 JB Racing Lightweight Aluminum Flywheel

T#:3772

Part#: 520-090-240

Ships in 4 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable.

Stock Flywheel Weight = 16.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1991-1995 E34 BMW M5

Show More Show Less

2002, E21 320i, E30 318i (M10) JB Racing Lightweight Aluminum Flywhee...

T#:3647

Part#: 520-110-215

Ships in 2 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can be rebuilt too with a new clutch contact surface.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 16.5lbs
JB Flywheel Weight = 8lbs

This item fits the following BMWs:
1974-1976 2002 BMW 2002
1977-1983 E21 BMW 320i
1984-1985 E30 BMW 318i

Show More Show Less

E30 M3 JB Racing Lightweight Aluminum Flywheel

T#:3768

Part#: 520-050-228

Ships in 4 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

Stock Flywheel Weight = 19.5lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1987-1991 E30 BMW M3

Show More Show Less

E39 540i 97-03 JB Racing Lightweight Aluminum Flywheel

T#:1339

Part#: 520-150-240

In Stock

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 33.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1997-2003 E39 BMW 540i

Show More Show Less

E24 633/635CSi/M6, E28 535i/M5 JB Racing Lightweight Aluminum Flywhee...

T#:3770

Part#: 520-080-240

Ships in 8 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 22.0lbs
JB Flywheel Weight = 8.5lbs

This flywheel includes the ignition trigger wheel.

This item fits the following BMWs:
1982-1987 E23 BMW 733i 735i
1982-1989 E24 BMW 633csi 635csi M6
1985-1988 E28 BMW 535i 535is M5

Show More Show Less

JB Racing Lightweight Aluminum Flywheel - E39 M5

T#:16606

Part#: 520-160-240

Ships in 8 Business Days

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 40.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1999-2003 E39 BMW M5

Show More Show Less

2002, 2002Tii JB Racing Lightweight Aluminum Flywheel 228mm

T#:3762

Part#: 520-100-228

In Stock

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can be rebuilt too with a new clutch contact surface.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 16.5
JB Flywheel Weight = 8lbs

This item fits the following BMWs:
1968-1973 2002 BMW 2002 2002tii

Show More Show Less

E30 325e JB Racing Lightweight Aluminum Flywheel (Replaces Single-Mas...

T#:3763

Part#: 520-070-228

Ships in 5 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325e up to 5/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 24.0lbs
JB Flywheel Weight = 8.5lbs

This item fits the following BMWs:
1984-1988 E30 BMW 325e 325es (with single mass flywheel)

Show More Show Less

ARP Performance Flywheel 22mm Bolt Kit - S14 2.3L

T#:302364

Part#: 201-2801

In Stock at Vendor

20% off MSRP $ 79.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 63.99 USD

Add to Wish List

Qty

20% off MSRP

$ 79.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 63.99 USD

Add to Wish List

ARP Flywheel Bolts are a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated, ensuring complete heat penetration, to increase the clamping load up to 200,000 psi. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best bolts we've found and we highly recommend them in any and all applications.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMW Engines:
S14 2.3L

Show More Show Less

E34 535i JB Racing Lightweight Aluminum Flywheel

T#:647

Part#: 520-170-240

Ships in 1 Business Day

$ 714.00 USD

Add to Wish List

Qty

$ 714.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Show More Show Less

Genuine BMW Flywheel - 2002tii

T#:22222

Part#: 11221252206

Special Order: No Guaranteed ETA

2% off MSRP $ 1,465.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,435.99 USD

Add to Wish List

Qty

2% off MSRP

$ 1,465.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,435.99 USD

Add to Wish List

Genuine BMW Flywheel - D= 228mm,8 Loch

Fits BMW Engines including:
M10

E30 M3 Sport Evo BMW Motorsport Lightweight Flywheel

T#:337968

Part#: 11221312519

Ships on Feb 15, 2027

Sale - Save 17% $ 1,013.99

This product was last offered at the strikethrough price on
05-07-2026

Starting at $ 837.91 USD

Add to Wish List

Sale - Save 17%

$ 1,013.99

This product was last offered at the strikethrough price on
05-07-2026

Starting at $ 837.91 USD

Add to Wish List

This Genuine BMW Motorsport part (used on the Sport Evo M3s) is a precision machined and balanced lightweight steel flywheel. The stock flywheel weights 19.5 lbs, the Motorsport flywheel is under 12 lbs! This lightweight flywheel will allow the motor to "spool up" faster, improving acceleration. This is a perfect flywheel upgrade for someone who does not want a full aluminum lightweight flywheel and also wants factory Motorsport parts on the E30 M3. After the Turner performance chip this is the next biggest "bang for the buck" for your M3. Flywheel mounting bolts available separately.

This item fits the following BMWs:
1987-1991 E30 BMW M3

Show More Show Less

JB Racing Lightweight Steel Flywheel - Grand-Am Legal - E46, MZ3, Z4 ...

T#:40748575

Part#: 520010240SGA

Ships on Sep 15, 2026

$ 868.00 USD

Add to Wish List

Qty

$ 868.00 USD

Add to Wish List

This lightened steel flywheel is specifically designed (and approved) for use in Grand-Am road racing but can also be used as a mild street upgrade if a full aluminum lightweight flywheel is not called for. The Grand-Am flywheel is 20% lighter than stock to meet the rules for the GS and ST classes.Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. The engine revs much faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

Grand-Am approved this flywheel to be used with a factory E36 M3 clutch. This opens up a lot of clutch and pressure plate options but we typically used this with a stock Sachs OEM clutch kit. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches.

Lightweight flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

If being used on a 330i 6-speed or Z4 6-speed an additional pilot bearing hub is required. Select your appropriate model and transmission from the list below.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 20.0lbs

This item fits the following BMWs:
2001-2002 E46 BMW 330i 330ci 5-speed
2003-2006 E46 BMW 330i 330ci 6-speed
2001-2006 E46 BMW M3
1998-2002 Z3 BMW Z3 M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i

Show More Show Less

Project Cars

SELECT YOUR BMW

ARP Performance Flywheel 28mm Bolt Kit - M20 2.5L

E36 M3, MZ3 JB Racing Lightweight Aluminum Flywheel

E30 318i/is, E36 318i, Z3 1.9 JB Racing Lightweight Aluminum Flywheel...

E60, E82, E85, E9X, E89 (N52 Engine) JB Racing Lightweight Aluminum F...

E46 M3 6MT JB Racing Lightweight Aluminum Flywheel

E46 323/325/328/330 5-speed, Z3 2.3/2.8/3.0 JB Racing Lightweight Alu...

JB Racing Single Mass Lightweight Aluminum Flywheel - 6-speed - E46 3...

E30 325i, E34 525i (M20) JB Racing Lightweight Aluminum Flywheel (Rep...

E34 M5 JB Racing Lightweight Aluminum Flywheel

2002, E21 320i, E30 318i (M10) JB Racing Lightweight Aluminum Flywhee...

E30 M3 JB Racing Lightweight Aluminum Flywheel

E39 540i 97-03 JB Racing Lightweight Aluminum Flywheel

E24 633/635CSi/M6, E28 535i/M5 JB Racing Lightweight Aluminum Flywhee...

JB Racing Lightweight Aluminum Flywheel - E39 M5

2002, 2002Tii JB Racing Lightweight Aluminum Flywheel 228mm

E30 325e JB Racing Lightweight Aluminum Flywheel (Replaces Single-Mas...

ARP Performance Flywheel 22mm Bolt Kit - S14 2.3L

E34 535i JB Racing Lightweight Aluminum Flywheel

Genuine BMW Flywheel - 2002tii

E30 M3 Sport Evo BMW Motorsport Lightweight Flywheel

JB Racing Lightweight Steel Flywheel - Grand-Am Legal - E46, MZ3, Z4 ...

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results