Rear End Links

These adjustable rear links are only required when using sway bar / swaybars with a suspension with a very low ride height, where it may be necessary to adjust the length of the end links for proper sway bar clearance from the drive axles or other suspension components. These suspensions are usually found only on race cars but this may also apply to street cars with sport springs/sport coil overs that are lowered a lot. On most street cars lowered 1.5" or less, the stock links will be fine.

These end links feature a Heim joint, which allows enough lateral movement when disconnected to adjust the length of the link without removing the entire link from the car. This is particularly helpful when eliminating or adjusting preload while tuning the suspension. Similar links without this joint, can't be adjusted without totally removing the link from the car.

Built-in grease fittings allow for occasional lube, and a packet of grease is included. These links are sold as a set, and include two end links and hardware for H&R and TMS sway bars (other brands may not need the hardware). 

At their shortest setting they are 2.875" hole to hole and on their longest setting they are 3.5" hole to hole.

*Note: these links will not work with factory or non-adjustable Eibach sway bars.

Black anodized billet sway bar end links to replace your flimsy and corroded factory units. Removable hardware for a lifetime serviceable component!

Your factory end link brackets are a one piece design with an integrated stud made of flimsy metal with no coating to protect from the elements. Over the years the end link hardware rusts right to the integrated stud and when you go to remove the end links or brackets they are one strong turn and a snap away from needing to be replaced.

Not only did ECS come up with a stronger solution with a superior resistance to corrosion but went the extra mile to incorporate hardware that can be replaced time and time again so you will never need to replace the brackets themselves. The end link brackets feature chamfers and locator pins to fit perfectly in factory location and make for a straight forward install. The brackets featuring a slotted area for the bolt head to sit so you don't have the headache of having to get a wrench in the tight space behind the bracket while installing them.

Kit Contents:

A pair of rear end link brackets
Hardware needed for installation
Part Design:

Billet aluminum brackets
Zinc coated hardware
Superior corrosion resistance
Large upgrade from factory components

Sway bar end links connect the swaybar to the rest of the suspension, preventing body roll and keeping everything in line in tight turns. This exposes these links to a high amount of stress and pressure, often leading to split bushings and sloppy body control and knocking noises. OEM Lemförder sway bar links are the perfect option to restore body control and eliminate knocking noises.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E70 X5,E71 X6,F15,F16

Sway bar end links connect the swaybar to the rest of the suspension, preventing body roll and keeping everything in line in tight turns. This exposes these links to a high amount of stress and pressure, often leading to split bushings and sloppy body control and knocking noises. OEM Lemförder sway bar links are the perfect option to restore body control and eliminate knocking noises.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
F01,F02,F06,F10,F12,F13

This is the OEM Lemforder replacement rear sway stabilizer bar link for E60 5 series and E63 6 series without Dynamic Drive. Sold individually.

This item fits the following BMWs:
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
2004-2010 E63 BMW 645ci 650i M6

Sway bar end links connect the swaybar to the rest of the suspension, preventing body roll and keeping everything in line in tight turns. This exposes these links to a high amount of stress and pressure, often leading to split bushings and sloppy body control and knocking noises. OEM Lemförder sway bar links are the perfect option to restore body control and eliminate knocking noises.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
2007 - 2010 E60 528i 535i 550i
2003 - 2006 E60 Sedan 525i 530i 545i 550i 
2004 - 2010 E63 6 Series Coupe 645Ci 650i 
2004 - 2010 E64 Convertible 645Ci 650i 

Replacement REAR sway bar / swaybar link for all 1997-2003 5 series sedans and wagons. Made by Lemforder. this is a very common wear item in the E39 suspension, especially when the car has been driven hard. While replacing this part, also check the sway bar bushing bracket for signs of stress or failure. It can be used on both the left and right side of the car. Two required per car, and are sold individually.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i M5

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to remedy this common issue with a set of Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. A unique knurled bushing design also ensures compatibility with the OEM sway bar, offering a first-to-market solution for enthusiasts looking to retain factory components.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits factory rear sway bars on E23, E24, E28, E30, and E36 Laser-etched markings for quick and easy adjustments

Sway bar end links connect the swaybar to the rest of the suspension, preventing body roll and keeping everything in line in tight turns. This exposes these links to a high amount of stress and pressure, often leading to split bushings and sloppy body control and knocking noises. OEM Lemförder sway bar links are the perfect option to restore body control and eliminate knocking noises.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Sway bar end links connect the swaybar to the rest of the suspension, preventing body roll and keeping everything in line in tight turns. This exposes these links to a high amount of stress and pressure, often leading to split bushings and sloppy body control and knocking noises. OEM Lemförder sway bar links are the perfect option to restore body control and eliminate knocking noises.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Fits the following BMW Chassis:
E38 BMW All Submodels

Enhance your Mini's suspension performance with stabilizer links that ensure optimal control and responsiveness on the road. When play develops in the joints, it's time for a replacement to minimize noise and maintain stability. These links connect from the sway bar end to the front strut section, reducing play and clunking noise for a smoother ride.

• Improves suspension control and responsiveness
• Minimizes noise and play in the joints
• Connects sway bar end to front strut section
• Requires one link for each wheel
• OEM supplier for guaranteed quality

Sway bar end links connect the swaybar to the rest of the suspension, preventing body roll and keeping everything in line in tight turns. This exposes these links to a high amount of stress and pressure, often leading to split bushings and sloppy body control and knocking noises. OEM Lemförder sway bar links are the perfect option to restore body control and eliminate knocking noises.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
F07 BMW 535i/iX 550i/iX

Sway bar end links connect the swaybar to the rest of the suspension, preventing body roll and keeping everything in line in tight turns. This exposes these links to a high amount of stress and pressure, often leading to split bushings and sloppy body control and knocking noises. Meyle HD sway bar links are the perfect option to restore body control and eliminate knocking noises.

Meyle is a German brand in business since 1958 and all of their products are TUV approved and meet or exceed ISO standards. Heavy Duty components are designed to provide significantly long lifespans than other aftermarket and stock OE components. Each part includes a 4 year warranty.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Features:

• 4 Year Warranty

• All metal ball joints are more reliable and longer lasting than stock

• Bushings are solid rubber rather than fluid filled, providing longevity and handling feel improvements

This item fits the following BMWs:
BMW 7 Series - 740i, 740iL, 750iL