Rear End Links

These adjustable rear links are only required when using sway bar / swaybars with a suspension with a very low ride height, where it may be necessary to adjust the length of the end links for proper sway bar clearance from the drive axles or other suspension components. These suspensions are usually found only on race cars but this may also apply to street cars with sport springs/sport coil overs that are lowered a lot. On most street cars lowered 1.5" or less, the stock links will be fine.

These end links feature a Heim joint, which allows enough lateral movement when disconnected to adjust the length of the link without removing the entire link from the car. This is particularly helpful when eliminating or adjusting preload while tuning the suspension. Similar links without this joint, can't be adjusted without totally removing the link from the car.

Built-in grease fittings allow for occasional lube, and a packet of grease is included. These links are sold as a set, and include two end links and hardware for H&R and TMS sway bars (other brands may not need the hardware). 

At their shortest setting they are 2.875" hole to hole and on their longest setting they are 3.5" hole to hole.

*Note: these links will not work with factory or non-adjustable Eibach sway bars.

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to address this common issue with Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. These end links feature a bolt-through bushing design, which is compatible with most adjustable aftermarket sway bars. Mounting hardware is included for easy installation.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits most aftermarket sway bars with bolt-through attachment Laser-etched markings for quick and easy adjustments

Direct replacement – can be used with either factory or Aftermarket rear anti-roll bar, and returned to standard at any time.

Designed with one aim in mind: to help achieve optimum suspension performance and geometric accuracy, and thus increase the effectiveness of your rear anti-roll bar.

Each heavy-duty, high-articulation rear end link attaches the rear anti-roll bar ends to the lower suspension arm. Replacing the failure-prone, weak plastic OEM links with our rigid billet aluminum links greatly reduces flex and allows a sharp, uncompromised transfer of suspension movement through to the sway bar.

As well as the link itself, extra stiffness and precision comes from replacing the flex-prone stock plastic ball joint with motorsport-spec ball joints. An especially valuable upgrade on older, higher mileage car.

Features:

Manufactured from Aircraft grade T6-6061 aluminum billet.

Complete OE replacements.

Our single-threaded ends make for easy length adjustment in-situ without having to detach and re-attach.

Each heavy-duty, high-articulation rear drop link.

Anodized in signature MMX Gloss black.

Heavy-duty ball joints to ensure a long life span.

Kit complete with everything you need.

Can be used with either factory or Aftermarket rear anti-roll bar, and returned to standard at any time.

Rubber boots for longevity and durability.