BMW Suspension Parts

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints(M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability

Optimize rear suspension geometry with Whiteline suspension bushings. Often overlooked, Whiteline trailing arm bushings offer superior dynamic alignment precision by controlling excessive movement - providing driver reassurance for more predictable handling.

Features:

• Performance - Whiteline's engineered "Synthetic Elastomer" bushings feature the quality ride of rubber at lower speeds and at higher speeds react when under cornering, accelerating and braking loads, for CHASSIS CONTROL and improved handling.
• Durable - The advanced synthetic elastomer characteristics ensure superior elasticity, memory and outright durability for all forms of driving applications!
• Resistant - Whiteline's synthetic elastomer formulation boasts resistance to oil, grease, ozone and weathering
• Lubricant - Supplied with extreme pressure molybdenum disulphide (LM) based grease (where required) for extended life.
• Installer Friendly - Designed with the installer in mind by reducing the need of specialized skills, tools and equipment.
• Black - The neutral (black) appearance favored by restorers and racers.
• Lifetime Warranty - All Whiteline bushing kits are backed by a lifetime warranty

BMW E46 Z4 Rear Polyurethane Differential Bushing Performance is the ultimate upgrade for enhancing the connection between your BMW's chassis and differential. Designed by Turner Motorsport, this performance bushing replaces the soft factory rubber with durable polyurethane, offering superior control and response. By minimizing vibrations and reducing deflection, this bushing ensures a more direct and responsive driving experience, making it a must-have for any performance-oriented BMW E46 or Z4 owner.

• Enhanced Performance: Replaces the soft factory rubber with durable polyurethane for improved driveline response.
• Reduced Vibrations: Minimizes vibrations between the chassis and differential, providing a more connected driving experience.
• Increased Durability: Made from high-quality polyurethane, offering long-lasting performance under demanding conditions.
• Improved Control: Reduces deflection, ensuring a more precise and responsive handling experience.

Dramatically improve performance and aesthetics with an average lowering up to 1.4" front and rear.

Take your F3x to the next level with upgraded performance and aesthetic. ECS lowering springs are specifically designed with both handling and comfort in mind for the best mix or performance and drivability. With an average lowering range of 1.0"-1.4" you have the added benefit of lower center of gravity providing superior cornering and better steering feedback. Lowering springs not only increase handling performance they provide an astounding aesthetic upgrade by decreasing the wheel gap and giving your car a more planted/fitted appearance.

FEATURES AND DESIGN:

MADE IN THE USA
Average lowering of 1.0" to 1.4"
Front spring rate: 184 lbs/in
Rear spring rate: 462 lbs/in
Lowered center of gravity
Linear style springs
Black powder coating with red ECS logo
Designed specifically for your chassis these F3x lowering springs feature a linear style spring similar to a coilover. The issue with coilovers is the rough ride due to a drastic drop and much higher spring rates. When you have higher spring rate like coilovers it takes much more force to compress the spring which leads to a much more rigid ride. ECS lowering springs provide a happy medium between the factory suspension and coilover suspension. These springs are stiffer than factory but softer than a coilover spring to achieve the balance of increased performance and aesthetics while retaining a comfortable ride.

What is spring rate?
​You may ask yourself "what is the spring rate and how does it affect my ride?" Spring rate is the amount of force needed to compress a spring one inch. For example if you have a spring rate of 300lbs per inch it will take 300lbs of force to compress the spring one inch. An average coilover for your F3x has over 400 lbs/in for the front and over 500 lbs/in for the rear, this means that it will take over 400lbs of force to compress your front spring one inch and over 500lbs of force to compress the rear one inch. The higher the spring rate, the more rigid your ride is going to be. ECS lowering springs for your F3x have a spring rate of 184 lbs/in in the front and 462 lbs/in, an increase over factory but much less than a coilover. You can now both understand and explain the benefits of lowering springs to find the best solution for you.

Fine-tuning your coilover damping shouldn’t mean stripping out your rear seats or interior panels. On many applications, rear shock adjusters are hidden behind carpet, trim, or seatbacks, making quick adjustments a hassle.

The ECS Rear Damping Extension Kit solves that problem with a clean and functional solution. These flexible extensions relocate the adjustment knobs to an easily accessible point above the rear shock towers, letting you dial in your suspension from inside the cabin, no disassembly required.

Installation is straightforward: simply drill a small access hole in your interior trim and route the extension cables through. The adjustment knobs can be removed to allow the line to pass through smaller openings, minimizing cutting. For proper installation, be sure to fully loosen the set screw, insert the cable, then securely tighten it using the provided Allen key.

Kit Includes:

(2) Rear damping adjuster extension cables

Installation hardware and Allen key

A smart upgrade for track cars, daily drivers, or anyone who values easy access to suspension tuning, without compromising interior fit and finish.

The polished aluminum ECS strut tower bar kit offers more than just good looks - it reduces chassis flex to stiffen the suspension, and helps to triangulate the front end, providing more consistent suspension geometry.

Strut tower plates should sit flush against the strut towers. If this is not the case, your strut towers are to some extent deformed. This can be easily remedied in minor cases with a block of wood and a hammer.

Due to their soft rubber construction, OE strut mounts are known to wear at an accelerated rate. Many high-mileage vehicles fall victim to strut mount failure, which is commonly associated with annoying clunks, groans, or rattles from the front suspension.

With this issue in mind, ECS Tuning developed their heavy-duty front strut mount with upgraded, higher durometer rubber to resolve sloppy handling and increase longevity. Manufactured precisely within OEM tolerances, these mounts are a perfect fit for your BMW.

Features:

Reduces deflection: Increases vehicle handling and cornering dynamics by removing deflection within the strut mount. Increases longevity: Upgraded rubber construction makes for a stiffer mount, less prone to cracking and general degradation. Developed in-house: Designed and tested by ECS Tuning engineers, this mount is sure to outlast an OE replacement. Upgrade to a better strut mount without sacrificing ride comfort! Improve longevity and ride control all at once.

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints: Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability

These bushings replace the stock rubber bushings and offer a better driving feel, increased lifespan, and better wheel alignment.

Rubber bushing allow for a lot more movement and are more susceptible to wear and tear from spirited driving and harsh weather conditions. Polyurethane is much more resistant to wear and is stiffer, reducing the total amount of movement that would normally affect the alignment negatively.

Elevate your driving experience with enhanced performance and aesthetics. ECS lowering springs are crafted to optimize both handling and comfort, striking the perfect balance between performance and drivability. With an average lowering range of 1.6", enjoy the benefits of a lower center of gravity, resulting in superior cornering and enhanced steering feedback. Not only do these lowering springs improve handling, but they also deliver a remarkable aesthetic transformation by reducing the wheel gap, giving your car a more planted and fitted appearance.

The example pictures shown are of both xDrive(Red F22) and Rwd(Blue F22)

Features and Design:

Average FRONT lowering of 1.0" - 1.4"
Average REAR lowering of 1.2" - 1.6"
Lowered center of gravity
Compatible with cars equipped with EDC
Linear style springs
Black powder coating with red ECS logo
MADE IN THE USA
Designed specifically for your chassis these ECS lowering springs feature a linear style spring similar to a coilover. The issue with coilovers is the rough ride due to a drastic drop and much higher spring rates. When you have a higher spring rate like coilovers, it takes much more force to compress the spring, leading to a much more rigid ride. ECS lowering springs provide a happy medium between the factory suspension and coilover suspension. Our springs are stiffer than factory but softer than a coilover spring to achieve the balance of increased performance and aesthetics while retaining a comfortable ride.

MINI F56 Front Sway Bar - 30mm Heavy Duty Fixed is engineered to enhance handling and performance by significantly reducing body roll. This sway bar improves cornering grip by evenly distributing lateral loads across the tires, resulting in better overall vehicle stability. Designed by Whiteline, this heavy-duty sway bar offers a cost-effective solution for upgrading your MINI’s handling without compromising ride quality or comfort.

• Reduces body roll for improved cornering stability
• Increases lateral grip by evenly distributing loads across tires
• Enhances overall handling and vehicle performance
• Improves safety and reduces tire wear
• Designed to maintain ride comfort and quality
• Heavy-duty 30mm fixed design for increased durability
• Engineered by Whiteline for high performance and reliability