BMW Drivetrain Parts

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E36 E46 Z...

T#:4988548

Part#: BMW04A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier - Street Bushings - BMW...

T#:4744858

Part#: BMW01A0-S

In Stock

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

The stock center support bearing carrier is engineered to minimize noise, vibration, and harshness (NVH) in the cabin by loosely securing the center bearing with a soft rubber bushing. However, this design allows the driveshaft to move off-center during launches and shifts, reducing throttle response and causing drivetrain oscillations. Over time, the rubber bushing can sag or dry rot, leading to misalignment of the driveshaft.

Prevent or fix this common problem with JXB Performance's Driveshaft Center Support Bearing Upgrade! This upgrade features a simple yet highly effective 2-piece design that makes installation and bushing replacement effortless. The stock carrier is cut away, and the JXB bushings securely "clamp" the driveshaft bearing in place, ensuring constant driveshaft alignment.

The Street bushing option from JXB is the most popular choice, offering a significant improvement over the stock design while keeping NVH levels minimal.

Note: Some light NVH, such as a soft hum, may occur at certain speeds. However, with a modified exhaust or open windows, it’s unlikely to be noticeable.

Installation is straightforward and doesn’t require removing the driveshaft. The 2-piece design clamps directly onto the OEM bearing, though removing the old carrier will require a cutting tool.

Need replacement or additional bushings? See T#4799658 for replacement street bushings.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E70/71 F1...

T#:6076533

Part#: BMW12A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E81/82/88...

T#:4744864

Part#: BMW01A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - G20 3-Series,...

T#:6076534

Part#: BMW13A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

Driveshaft Carrier Spare Bushing Set - Track

Spare bushings only - does not include new carrier assembly

T#:4799659

Part#: BSH04A1

In Stock

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

Refresh all bushings in your driveshaft carrier kit. Please note that the bushings you receive will depend on your specific model of carrier and may not match the picture.

Driveshaft Carrier Spare Bushing Set - Street

Spare bushings only - does not include new carrier assembly

T#:4799658

Part#: BSH04A0

Ships in 5 Business Days

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

Refresh all bushings in your driveshaft carrier kit. Please note that the bushings you receive will depend on your specific model of carrier and may not match the picture.

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E39 540i ...

T#:6061694

Part#: BMW06A0

Ships in 1 Business Day

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

Clutch Alignment Tool - E46, E39, Z3

T#:5426

Part#: BMW02

Ships on Aug 31, 2026

$ 22.99 USD

Add to Wish List

Qty

$ 22.99 USD

Add to Wish List

This clutch alignment tool exactly replicates the shaft and splines of the vehicle's drive shaft. It is made of high quality polypropylene injected plastics and insures perfect alignment of the clutch. Extremely durable, the clutch tool can be used over and over again. A must for anybody replacing a clutch. Spline = 28.575MM

This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1997-2003 E39 BMW 525i 528i 530i M5
1999-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 3.0i

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E60/61 E6...

T#:22394036

Part#: 4744865TCKTS6J5G

In Stock

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

Short Shift Kit

T#:31423729

Part#: 1221982020

Ships in 6 Business Days

$ 175.00 USD

Add to Wish List

Qty

$ 175.00 USD

Add to Wish List

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E30 RWD (...

T#:6061687

Part#: BMW03A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E60/61 E6...

T#:4744865

Part#: BMW02A0

Ships in 1 Business Day

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW F01/02 7-...

T#:6076536

Part#: BMW14A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E85/E86 Z...

T#:18070238

Part#: 7687533TCKHMEMIR

In Stock at Vendor

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

JXB Driveshaft Center Support Bearing Carrier Upgrade

T#:25772541

Part#: 4507854PDKNGJY2Q

Ships in 5 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E85/E86 E...

T#:7687533

Part#: BMW15A0

In Stock at Vendor

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

Driveshaft Center Support Bearing Carrier - Track Bushings

T#:6151348

Part#: BMW13A0-T

Ships in 5 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

The stock center support bearing carrier utilizes an extremely thin layer of rubber to secure the driveshaft, allowing for minimal movement to effectively insulate the cabin from noise, vibration, and harshness (NVH). However, this design is less effective at maintaining proper bearing alignment under heavy loads. Over time, it allows the bearing to gradually sag, disrupting the driveshaft alignment and introducing play in the driveline during gear shifts and throttle application. The original equipment manufacturer (OEM) rubber bushing has a tendency to sag, become brittle, and eventually deteriorate, resulting in dry rot and cracking. Even in well-maintained vehicles, the stock bushing can develop cracks in as little as 5-10 years. When the bushing loses its integrity, it can lead to pronounced vibrations, clunking noises, and increased stress on the bearing. Adding to the challenge, the stock carrier is permanently molded onto the center support bearing, making replacement a difficult task that typically necessitates specialized tools.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E30 3-Ser...

T#:6061699

Part#: BMW09A0

In Stock

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

Clutch Alignment Tool - 10-SPline - 1.380" - .580" Pilot

T#:5425

Part#: BMW01

In Stock

$ 22.99 USD

Add to Wish List

Qty

$ 22.99 USD

Add to Wish List

This clutch alignment tool exactly replicates the shaft and splines of the vehicle's drive shaft. It is made of high quality polypropylene injected plastics and insures perfect alignment of the clutch. Extremely durable, the clutch tool can be used over and over again. A must for anybody replacing a clutch.
Spline = 34.925MM

This item fits the following BMWs:
1999-2003 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2001-2006 E46 BMW M3
1997-2003 E39 BMW 530i 540i M5
2000-2002 Z3 BMW Z3 3.0i

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade

T#:25540331

Part#: 4488208PDKVXXZYU

In Stock

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW F10 M5, F...

T#:6061697

Part#: BMW08A0

In Stock

Sale - Save 19% $ 299.99

This product was last offered at the strikethrough price on
05-15-2026

Starting at $ 242.84 USD

Add to Wish List

Sale - Save 19%

$ 299.99

This product was last offered at the strikethrough price on
05-15-2026

Starting at $ 242.84 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

Driveshaft Center Support Bearing Carrier - Street & Track Bushings ...

T#:6061648

Part#: BMW07A0-B

Ships in 5 Business Days

$ 329.99 USD

Add to Wish List

Qty

$ 329.99 USD

Add to Wish List

The original center support bearing carrier from the factory employs a thin layer of rubber to secure the driveshaft, minimizing movement to reduce noise and vibrations in the vehicle's cabin. However, this design struggles to maintain the bearing's alignment under load, leading to gradual sagging and misalignment of the driveshaft. This, in turn, results in play during gear shifts and throttle application. Even in well-maintained vehicles, the initial rubber bushing can deteriorate and turn brittle, often developing cracks within 5-10 years. When this deterioration occurs, it can lead to heightened vibrations, clunking noises, and increased stress on the bearing. Additionally, replacing the stock carrier is a challenging task because it is permanently connected to the center support bearing, necessitating specialized tools for replacement.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E3 E10 E1...

T#:6061700

Part#: BMW10A0

Ships in 4 Business Days

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E65 E66 7...

T#:6061690

Part#: BMW05A0

Ships in 4 Business Days

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E60 M5, E...

T#:6061696

Part#: BMW07A0

Ships in 4 Business Days

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less

Clutch Alignment Tool - E46 E60 E83 X3 E53 X5

T#:11930

Part#: BMW103

In Stock

Sale - Save 57% $ 22.99

This product was last offered at the strikethrough price on
05-14-2026

$ 9.80 USD

Add to Wish List

Qty

Sale - Save 57%

$ 22.99

This product was last offered at the strikethrough price on
05-14-2026

$ 9.80 USD

Add to Wish List

This clutch alignment tool exactly replicates the shaft and splines of the vehicle's drive shaft. It is made of high quality polypropylene injected plastics and insures perfect alignment of the clutch. Extremely durable, the clutch tool can be used over and over again. A must for anybody replacing a clutch.

This item fits the following BMWs:
2004-2005 E46 BMW 325i 325ci 325xi 330i 330ci 330xi - 6 speed
2004-2005 E60 BMW 525i 530i
2004-2006 E83 BMW X3 2.5i X3 3.0i
2004-2006 E53 BMW X5 3.0i

Show More Show Less

Clutch Alignment Tool - 10-Spline - 1 1/8" - .470" Pilot

T#:5423

Part#: TLS-33-28

In Stock

$ 18.99 USD

Add to Wish List

Qty

$ 18.99 USD

Add to Wish List

This clutch alignment tool exactly replicates the shaft and splines of the vehicle's drive shaft. It is made of high quality polypropylene injected plastics and insures perfect alignment of the clutch. Extremely durable, the clutch tool can be used over and over again. A must for anybody replacing a clutch.

This item fits the following BMWs:
1970-1976 2002 BMW 1600 2002 2002tii
1984-1985 E30 BMW 318i 318is 318ic
1984-1991 E30 BMW 325e 325es 325i 325ic 325is 325ix M3
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1982-1989 E24 BMW 633csi 635csi M6

Show More Show Less

Clutch Alignment Tool - 10-Spline - 1 1/8" - .590" Pilot

T#:5422

Part#: TLS-33-83

In Stock

$ 18.99 USD

Add to Wish List

Qty

$ 18.99 USD

Add to Wish List

This clutch alignment tool exactly replicates the shaft and splines of the vehicle's drive shaft. It is made of high quality polypropylene injected plastics and insures perfect alignment of the clutch. Extremely durable, the clutch tool can be used over and over again. A must for anybody replacing a clutch.

This item fits the following BMWs:
1990-1991 E30 BMW 318i 318is 318ic with M42 engine
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i 530i 540i
2001-2003 E39 BMW 525i

Show More Show Less

Clutch Alignment Tool - 10-Spline - 1 3/8" - .590" Pilot

T#:5424

Part#: TLS-33-25

In Stock

$ 7.99 USD

Add to Wish List

Qty

$ 7.99 USD

Add to Wish List

This clutch alignment tool exactly replicates the shaft and splines of the vehicle's drive shaft. It is made of high quality polypropylene injected plastics and insures perfect alignment of the clutch. Extremely durable, the clutch tool can be used over and over again. A must for anybody replacing a clutch.

This item fits the following BMWs:
onvertible
1993-1995 E34 BMW 540i

Show More Show Less

Driveshaft Center Support Bearing Carrier - Track Bushings

T#:6061652

Part#: BMW08A0-T

Ships in 5 Business Days

Sale - Save 15% $ 299.99

This product was last offered at the strikethrough price on
05-15-2026

$ 255.67 USD

Add to Wish List

Qty

Sale - Save 15%

$ 299.99

This product was last offered at the strikethrough price on
05-15-2026

$ 255.67 USD

Add to Wish List

The stock center support bearing carrier utilizes an extremely thin layer of rubber to secure the driveshaft, allowing for minimal movement to effectively insulate the cabin from noise, vibration, and harshness (NVH). However, this design is less effective at maintaining proper bearing alignment under heavy loads. Over time, it allows the bearing to gradually sag, disrupting the driveshaft alignment and introducing play in the driveline during gear shifts and throttle application. The original equipment manufacturer (OEM) rubber bushing has a tendency to sag, become brittle, and eventually deteriorate, resulting in dry rot and cracking. Even in well-maintained vehicles, the stock bushing can develop cracks in as little as 5-10 years. When the bushing loses its integrity, it can lead to pronounced vibrations, clunking noises, and increased stress on the bearing. Adding to the challenge, the stock carrier is permanently molded onto the center support bearing, making replacement a difficult task that typically necessitates specialized tools.

Show More Show Less

Race-Spec Dual-Clutch Transmission Oil Cooler - F8X M3 M4

T#:25971912

Part#: VF-DCTCOOLERF8X

Ships on Aug 31, 2026

$ 599.00 USD

Add to Wish List

Qty

$ 599.00 USD

Add to Wish List

This heat exchanger features a dual-pass high-performance core that offers 30% more efficiency than its factory counterpart. This kit will keep your transmission fluid cool no matter the outside temperature!

Show More Show Less

Driveshaft Center Support Bearing Carrier Upgrade - BMW E46 (AWD) 3 S...

T#:34382132

Part#: BMW17A0

Ships in 5 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

Driveshaft Center Support Bearing Carrier Upgrade - BMW E46 (AWD) 3 S...

T#:34382135

Part#: BMW17A0SH

Ships in 4 Business Days

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

Driveshaft Center Support Bearing Carrier Upgrade - BMW E46 (AWD) 3 S...

T#:34382133

Part#: BMW17A0-H

Ships in 5 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

Driveshaft Center Support Bearing Carrier - Track Bushings

T#:6151351

Part#: BMW12A0-T

Ships in 6 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

The stock center support bearing carrier utilizes an extremely thin layer of rubber to secure the driveshaft, allowing for minimal movement to effectively insulate the cabin from noise, vibration, and harshness (NVH). However, this design is less effective at maintaining proper bearing alignment under heavy loads. Over time, it allows the bearing to gradually sag, disrupting the driveshaft alignment and introducing play in the driveline during gear shifts and throttle application. The original equipment manufacturer (OEM) rubber bushing has a tendency to sag, become brittle, and eventually deteriorate, resulting in dry rot and cracking. Even in well-maintained vehicles, the stock bushing can develop cracks in as little as 5-10 years. When the bushing loses its integrity, it can lead to pronounced vibrations, clunking noises, and increased stress on the bearing. Adding to the challenge, the stock carrier is permanently molded onto the center support bearing, making replacement a difficult task that typically necessitates specialized tools.

Show More Show Less

Quick Shift Kit 122 19 56 030 for B46 B48 2.0L

T#:26238484

Part#: 1221956030

In Stock

$ 145.00 USD

Add to Wish List

Qty

$ 145.00 USD

Add to Wish List

Enhance the shifting experience of your Mini Cooper S Gen 3 with this quick shift kit. Crafted with precision CNC machining from billet aluminum, this kit reduces shift travel by approximately 40%, providing smoother and quicker gear changes. With its large adjustment range, drivers can customize the shift lever travel to suit their driving preferences. Adjustment can be easily done from inside the car using a 16 mm wrench. The kit includes a convenient removal tool to assist in removing the OEM shifter.

Precision CNC machined from billet aluminum
Reduces shift travel by approximately 40%
Large adjustment range for personalized shift lever travel
Easy adjustment from inside the car
Includes removal tool for OEM shifter

Show More Show Less

JXB Driveshaft Center Support Bearing Carrier Upgrade - BMW E53 X5 ...

T#:6076532

Part#: BMW11A0

Ships in 8 Business Days

Starting at $ 299.99 USD

Add to Wish List

Starting at $ 299.99 USD

Add to Wish List

The stock center support bearing carrier is designed to reduce NVH to the cabin by loosely holding the center bearing with a flimsy rubber bushing. During launches and shifts, the driveshaft is allowed to travel off-center, decreasing throttle response and causing oscillations through the drivetrain. As they age, the carrier rubber sags and dry rots, ruining the driveshaft alignment. Fix or prevent this common issue with JXB Performance's Driveshaft Center Support Bearing Upgrade! JXB utilizes a simple but extremely effective 2-piece design which allows you to install this upgrade and replace bushings with ease. The stock center support carrier is simply cut away, allowing the JXB bushings to "clamp" down on the driveshaft bearing and hold the driveshaft securely in place, maintaining driveshaft alignment at all times. Two bushing options are available for this kit, Street and Track, both of which are many times better than the stock bushings: The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. (With a modified exhaust or windows down, you’ll probably never hear it) The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? Try them both, they’re interchangeable! Installation does not require the removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Looking for replacement or additional bushings? See T#4799658 for replacement street bushings and T#4799659 for replacement track bushings.

Show More Show Less