BMW Engine Parts

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the current replacement for some BMW 6 and 8-cylinder engines built in the late 2000s and after. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. It's listed as a replacement coil for N20, N55, and S55 engines. In March 2015 BMW approved it for N51/N52 engines. This part number replaces the previous BMW part number 12137594937 for the cars listed below.

Sold per coil. Includes boot and connector.

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

Ferrea valve springs are developed from high strength alloys, including premium grade chrome silicone steel These springs are manufactured with state-of-the-art equipment. Ferrea springs are heat-treated and stress-relieved, which dramatically increases the spring's life. Strict quality control procedures and cycle testing ensures consistency from batch to batch. Ferrea valve springs provide the stability needed for high lift, high rpm racing and street car engines. Kit includes a set of 24 springs. MUST be used with the Ferrea Spring Seat and Titanium Retainers. See links below. 

https://www.turnermotorsport.com/e/p-163-e36-325-328-m3-ferrea-spring-seat-set/ 

https://www.turnermotorsport.com/e/p-31-e36-325-328-m3-ferrea-titanium-retainer-set/

This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i