Turner Motorsport has everything you need to upgrade your BMW through our stages of performance or to keep your car in peak condition with our range of the latest in proven OEM cooling parts. Upgrade your cooling system and engine performance with the selections below to give your BMW a performance and reliability advantage.
Free additional power to your M3’s rear wheels without sacrificing or compromising your BMW’s reliability. Machined from 6061-T6 aerospace aluminum, Macht Schnell Performance Underdrive Pulleys are strong as well as lightweight to limit parasitic drag from the accessories within a moderate level for maximum performance on or off the track. After machining and engraving, pulleys are then T3 hard anodized for additional strength, anti-corrosion & wear resistance. Our DualDrive design replaces the Crank Accessory & Power Steering Pulleys, resulting in an additional 9-14 HP and 7-9ft. lbs TQ gain for the M3. Gains are due to a reduction in power required to turn accessories; an increase in accessories lifespan due to lower speed will also result. All factory harmonics/balancing are undisturbed. Macht Schnell Performance Underdrive Pulleys have no negative effect on accessory operation and comes fully equipped with new belts. Already have this kit and need new belts? See T#14491 and T#14489 Performance Underdrive Pulleys Features: DualDrive design allows maximum performance, with minor effect on accessory speed Proper cooling temperatures are retained at proper levels on or off the track Maintains proper alternator speed, allowing sustained levels to sensitive control modules Machined from 6061-T6 aerospace aluminum T3 Hard-Anodized for maximum strength and corrosion/wear resistance No affects to crankshaft dampening or harmonics Simple bolt-on installation
Show More Show Less
OMP Battery Cut Off Switch / Kill Switch, for use in racecars as an emergency "kill switch", to depower the electrical system in the event of a crash or other emergency. This cut off switch is FIA approved, has 6 poles and alternator protection, as well as a removable key.
Show More Show Less
Eliminate your squeaking accessory belt pulley and cracked drive belt with this upgraded accessory belt service kit! This kit includes the ECS Kevlar Reinforced Accessory Belt, tensioner assembly, and your idler pulley. ECS Tuning's Red Kevlar Accessory Belts are both an aesthetic improvement and a performance alternative to a traditional belt. Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Refreshing the rollers and/or tensioners simultaneously is a great way to ensure all vital components of your drive belt system are functioning optimally for years to come!
Show More Show Less
Modern engines are designed to consume no oil. Even with advanced technology, sometimes an old fashion solution is the best kind. Oil consumption is a leading cause of poor fuel economy, failed emissions, and exhaust smoke. This catch can kit comes complete and ready to separate air and oil so your engine can breathe properly again. Features: Increases Air Intake Efficiency Promotes Engine Longevity Non-Clogging Air/Oil Separation Double Baffle Free Flow Solid No Restriction Design Large Intake / Exhaust No Tapering Down Stealth Mounting on Cool Side of the Motor Anodized Black Lightweight Aluminum
Show More Show Less
If you are planning on running additional boost, keeping tabs on the level is going to be an important factor. For doing this you have many options...Apps, scanners, coding. But what about a good old mechanical gauge? Now you can add one the easy way with this sandwich plate adapter from FTP. Simply remove the factory boost sensor install the plate, re-bolt the boost sensor and you're done.
Show More Show Less
This plate is a simple way to add a bespoke look to your engine bay. If you have replaced your oil thermostat or deleted your cooler, now is the perfect time for this mod. Installs in minutes and ensures a positive seal for the oiling system.
Show More Show Less
The turbocharged E9X 335i is renowned for its excellent performance and the ability to custom tune for more horsepower. Unfortunately, it is also known for oil cooling deficiencies that can reduce horsepower output and potentially compromise engine longevity, especially when driven enthusiastically or when boost is increased. To help maximize the power of your BMW, this FTP Motorsport kit adds a second oil cooler behind the kidney grills in addition to the factory oil cooler. This not only increases the cooling capacity, but more than DOUBLES it! Our kit provides the factory oil cooler with much more airflow then what is available in the fender wells. Only for vehicles with factory oil cooler
Show More Show Less
The OEM plastic PCV valve does not hold pressure well even when brand new. What this means is that when the turbochargers are making boost, pressurized air can become forced backwards through the valve and back into the crankcase. Depending on the condition of your PCV valve this can range from irritating to dangerous as a pressurized case can cause all sorts of issues. Additionally, if your valve cover is cracked due to age or has a bad gasket you are more than likely experiencing a pressure leak either internally or externally. These two features can cause even a low-mileage N54 to run like a tired elephant, sometimes even unlocking a special bonus function known as "Limp Mode". The solution is to replace any failed components and upgrade the PCV valve to something more capable withstanding the abuse of a turbocharged environment. FTP Motorsport has you covered with this solid aluminum valve assembly. It is essentially the same thing that came in your car from the factory, made out of aluminum. The internal components have also been made to fit tighter and outlast the life of an off the shelf replacement. No, this won't be the very last PCV valve you buy, but it will most certainly alleviate a lot of headaches common to N54 owners. And if you're tuned, big twin or single swapped you need one of these yesterday.
Show More Show Less
2007-2010 E90/E92/E93 335i N54 Stage 1+ Performance Package Peak Power Gain*: up to 103hp / 108ft-lbs + aFe Pro5R Dual Cone Intake + Wagner Front Mount Intercooler + Cobb AccessPort programmer
More power = more heat. It's easy to make more power one time but to continue making that power consistently requires careful planning and design. With the additional boost the air entering the engine is also warmer, making the intercooler more important than ever. In testing, the stock BMW intercooler was quickly overwhelmed and cannot keep the intake air cool enough. The engine computer recognizes that and dials back the boost. A more efficient intercooler will keep boost levels up, delivering consistently higher boost levels. The Stage 1+ package includes a Wagner Evo I plug and play intercooler upgrade. We get great feedback from our customers and technicians about the Wagner FMIC - it's a direct bolt in part using all of the factory piping and it offers 85% more surface area than the factory intercooler.
The aFe Dual Cone intake and Cobb Accessport programmer complete the Stage 1+ package. The larger surface area of the aFe cone filters allows more air to enter the engine - creating more power and torque, a richer engine sound, and better throttle response. The kit is supplied complete with aFe Pro5R filters, mounting shield, intake tubes, sealing materials, hardware, and install instructions. The torque increase and sound from the open intake from low-mid RPM is sensational.
The Cobb software tool puts multiple tuning stages in the palm of your hand. Our Stage 1+ package lines up with the Cobb Stage 1 tuning maps for an intake and FMIC (91 or 93+ octane fuel). Simply download the Stage 1+ map from the Cobb website, plug it in, and install. Select different maps for other upgrades, throttle settings, octane ratings, valet mode, or revert back to stock! If you're moving up in Stages simply download a new file from the Cobb website and update your AccessPort programmer! The AccessPort triples as a diagnostic tester/reader and a data logger. It's the most feature-packed programmer on the market today.
We have taken the guesswork out of choosing the best upgrades for the N54 engine. If you follow the upgrade path we have laid out you will have very satisfying and reliable results. The addition of the larger intercooler makes Stage 1 more enjoyable and won't let you down at the track or dragstrip. * Note that peak power gains are quoted remain the same as Stage 1 but the cooler intake air means there is less of a chance the engine computer will cut power from heatsoak.
This item fits the following BMWs: 2007-2010 E90 BMW 335i 335xi 335i xDrive - Sedan 2007-2010 E92 BMW 335i 335is* 335xi 335i xDrive - Coupe 2007-2010 E93 BMW 335i - Convertible * 335is horsepower gains are lower due to the factory power boost in the "is" package Show More Show Less
